Advertisement
a POWER
•
Turn on/off the unit.
•
Switch to standby mode.
b DBB
•
Turns on or off dynamic bass boost.
c
•
Stop play or erase a program.
d
•
Start or pause play.
e
/
•
Skip to the previous/next track.
•
Search within a track or disc.
•
Tune to a radio station.
f VOL +/-
•
Adjust volume.
g PRESET +/-
•
Select a preset radio station.
h DISPLAY
•
Show current status.
i MUTE
•
Mute or restore volume.
j PROG
•
Program tracks.
•
Program radio stations.
k REPEAT
•
Play a track or all tracks repeatedly.
l SOURCE
•
Select a source: disc, FM, or AUX.
3 Connect
Connect speakers
Note
•
Insert the stripped portion of each speaker wire into the socket completely.
•
For optimal sound, use the supplied speakers only.
•
Connect only speakers with impedance that is the same or higher than the supplied
speakers. Refer to the Specifications section of this manual.
1
For one speaker, insert the red wire to the red (R+) socket on the back of the main unit, and the black
wire into the black (R-) socket.
2
For another speaker, repeat step 1 to insert the wires into the red (L+) and the black (L-) socket.
To insert each speaker wire:
1
Hold down the socket flap.
2
Insert the speaker wire fully.
3
Release the socket flap.
Connect power
Caution
•
Risk of product damage! Make sure that the power supply
voltage corresponds to the voltage printed on the back
or the underside of the Micro Hi-Fi system.
•
Before connecting the AC power cord, make sure that
you have completed all other connections.
Connect the AC power cable to the power outlet.
4 Get started
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number
and serial number are on the bottom of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
MC127_05_UM_V1.1.indd 2
Prepare the remote control
Caution
•
Risk of explosion! Keep batteries away from heat,
sunshine or fire. Never discard batteries in fire.
•
Risk of decreased battery life! Never mix different brands
or types of batteries.
•
Risk of product damage! When the remote control is not
used for long periods, remove the batteries.
•
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
For first-time use:
1
Remove the protective tab to activate the remote control battery.
To replace the remote control battery:
1
Open the battery compartment.
2
Insert one CR2025 battery with correct polarity (+/-) as indicated.
3
Close the battery compartment.
1
1
2
2
3
3
Turn on
Press POWER.
The unit switches to the last selected source.
»
Switch to standby
Press POWER again to switch the unit to standby mode.
»
The red standby indicator turns on.
»
The backlight on the display panel turns off.
5 Play disc
1
Press SOURCE repeatedly to select the disc source.
2
Open the disc compartment.
3
Insert a disc with the printed side facing up.
4
Close the disc compartment.
•
To pause/resume play, press
.
•
To stop play, press
.
Play options
Skip to a track
During play, press
/
to select another track.
Search within a track
1
During play, press and hold
/
.
2
Release to resume normal play.
Display play information
During play, press DISPLAY repeatedly to select different play information.
Program tracks
You can program a maximum of 20 tracks.
1
In disc mode, in the stop position, press PROG to activate the program mode.
» P-] (program) is displayed.
[
2
to select a track number, and then press PROG to confirm.
Press
/
3
Repeat steps 1 to 2 to select and store all tracks to program.
4
Press
to play the programmed tracks.
P-] is displayed.
»
During play, [
•
To erase the program, in the stop position, press
.
Repeat play
1
During play, press REPEAT repeatedly to select:
r1]: play the current track repeatedly.
•
[
rA]: play all tracks repeatedly.
•
[
2
To return to normal play, press REPEAT repeatedly until repeat mode is no longer displayed.
6 Adjust volume level and sound effect
Adjust volume level
During play, press VOL +/- to increase/decrease the volume level.
Enhance bass
During play, press DBB to turn on or off dynamic bass enhancement.
Mute sound
During play, press MUTE to mute or restore the volume.
7 Listen to radio
Tune to a radio station
1
Press SOURCE repeatedly to select FM source.
2
Press and hold
/
for more than 2 seconds.
»
The radio tunes to a station with strong reception automatically.
3
Repeat step 2 to tune to more stations.
•
To tune to a weak station, press
/
repeatedly until you find optimal reception.
Program radio stations automatically
Note
•
You can program a maximum of 20 preset FM radio stations.
In tuner mode, press and hold PROG for more than 2 seconds to activate automatic program mode.
» AUTO] is displayed.
[
»
All available stations are programmed in the order of waveband reception strength.
The first programmed radio station is broadcast automatically.
»
Program radio stations manually
Note
•
You can program a maximum of 20 preset radio stations.
1
Tune to a radio station.
2
Press PROG to activate program mode.
» P-] is displayed.
[
3
Press PRESET +/- to allocate a number to this radio station, and then press PROG to confirm.
»
The preset number and the frequency of the preset station are displayed.
4
Repeat the above steps to program other stations.
Tip
•
To overwrite a programmed station, store another station in its place.
Select a preset radio station
In tuner mode, press PRESET +/- to select a preset number.
Tip
•
Position the antenna as far as possible from TV, VCR or other radiation source.
•
For optimal reception, fully extend and adjust the position of the antenna.
8 Other features
Listen to an external device
You can listen to an external device through this micro Hi-Fi system.
1
Press SOURCE repeatedly to select AUX source.
2
Connect the supplied MP3 link cable to:
•
MP3 LINK jack (3.5 mm) on the unit
•
the headphone jack on an external device
3
Start to play the device (see the device user manual).
9 Product information
Note
•
Product information is subject to change without prior notice.
Specifications
Amplifier
Rated Output Power
2 x 2 W RMS
Frequency Response
60 - 16 kHz, ±3 dB
Signal to Noise Ratio
>50 dBA
Aux Input
0.5 V RMS 20 kohm
Disc
Laser Type
Semiconductor
Disc Diameter
12 cm/8 cm
Support Disc
CD-DA, CD-R, CD-RW
Audio DAC
24 Bits / 44.1 kHz
Total Harmonic Distortion
<1%
Frequency Response
60 Hz -16 kHz (44.1 kHz)
S/N Ratio
>50 dBA
Tuner
Tuning Range
FM: 87.5 - 108 MHz
Tuning grid
50KHz
Sensitivity
<22 dBf
- Mono, 26dB S/N Ratio
<43 dBf
- Stereo, 46dB S/N Ratio
Search Selectivity
>28 dBf
Total Harmonic Distortion
<3%
Signal to Noise Ratio
>55 dB
Speakers
Speaker Impedance
8 ohm
Speaker Driver
3.5" full range
Sensitivity
>82 dB/m/W
General information
AC power
220 - 240 V, 50 Hz
Operation Power
12 W
Consumption
Standby Power Consumption
<1 W
Dimensions
- Main Unit (W x H x D)
152 x 175 x 205 mm
- Speaker Box (W x H x D)
132 x 175 x 158 mm
Weight
- With Packing
3.82 kg
- Main Unit
1.1 kg
- Speaker Box
2 x 0.9 kg
10 Troubleshooting
Caution
•
Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, check the following points before requesting service.
If the problem remains unsolved, go to the Philips web site (www.philips.com/welcome). When you contact
Philips, ensure that the apparatus is nearby and the model number and serial number are available.
No power
•
Ensure that the AC power cord of the unit is connected properly.
•
Ensure that there is power at the AC outlet.
•
As a power-saving feature, the system switches off automatically 15 minutes after track play reaches the
end and no control is operated.
No response from the unit
•
Disconnect and reconnect the AC power plug, and then turn on the system again.
No sound or poor sound
•
Adjust the volume.
•
Check if the speakers are connected correctly.
•
Check if the stripped speaker wires are clamped.
Remote control does not work
•
Before you press any function button, first select the correct source with the remote control instead of
the main unit.
•
Reduce the distance between the remote control and the unit.
•
Insert the battery with its polarities (+/– signs) aligned as indicated.
•
Replace the battery.
•
Aim the remote control directly at the sensor on the front of the unit.
No disc detected
•
Insert a disc.
•
Check if the disc is inserted upside down.
•
Wait until the moisture condensation at the lens has cleared.
•
Replace or clean the disc.
•
Use a finalized CD or correct format disc.
Poor radio reception
•
Increase the distance between the unit and your TV or VCR.
•
Fully extend the antenna.
2011-6-14 13:55:20
Advertisement
