CCD COLOR CAMERA IK-6210A/IK-6410A Please read this manual thoroughly before use, and keep it handy for future reference. TABLE OF CONTENTS IMPORTANT SAFEGUARDS ... 2 1. FEATURES AND DESCRIPTION ... 4 2. COMPONENTS ... 4 3. PART NAMES AND FUNCTIONS ... 5 4.
IMPORTANT SAFEGUARDS 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions The safety instructions and instruction manual should be retained for future reference. 3. Warnings Comply with all warnings on the product and in the instruction manual.
Page 3
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”...
7. Easy back focus adjustment for an easy installation. 8. Built-in 1/3 inch high – resolution CCD. (IK-6410A) 9. Minimum illumination of 0.2 lux at F1.2. (IK-6210A) Minimum illumination of 0.2 lux at F1.0. (IK-6410A) 10. S/N ratio of 50dB.
4. CAMERA INSTALLATION Wall 9.5 (0.37) Installation Example 1/4"-20UNC 112 (4.41) 15 (0.59) The Installation example is for reference only. Mounting bracket is not included. Dimensions : mm (inch) - 6 - 01_p2-p32 06.8.7, 11:08 AM...
5. CONNECTIONS AND OPERATIONS • Power plugs of connected equipment must be disconnected before camera installation. • A 75-ohm coaxial cable with connector (3C-2V or 5C-2V) is required for standard connection. • For details of wiring and operation of equipment to be connected, refer to their operation manuals.
Page 8
5-2. Line-Lock Control • Matching the vertical synchronization with the power frequency is called the Line-Lock. • This function is activated when the LL switch is set to ON. • When two or more cameras are switched by the video switcher for viewing by a monitor TV, the vertical sync.
6. LENS Back-Focus Adjusment Back-Focus is adjusted at the factory to accommodate most standard lenses. Sometimes, slight adjustment to the camera back-focus is necessary. Loosen the Focus Lock Screw. Achieve a clear image by rotating the focus ring. Tighten the Focus Lock Screw. Auto-iris Lens This camera supports two types of auto-iris lens: Video and DC (direct drive) types.
7. LINE-LOCK PHASE If two or more cameras within a system have different AC line phases are switched by the video switcher, the picture on the monitor TV will fluctuate vertically. Connect 24V AC input lines of all cameras so that they all share the same phase.
8. AUTOMATIC ELECTRONIC SHUTTER (AES) Exposure time is controlled automatically within a range of 1/60 sec. to 1/100000 sec. to obtain an adequate signal when the IRIS switch is moved to AES. When the back panel switch is turned to VIDEO or DC, the exposure time is fixed 1/60 sec. 9.
10. NOTES ON USE AND INSTALLATION • Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off. • Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen.
Ambient humidity Weight External dimensions Automatic electronic shutter 01_p2-p32 IK-6210A 24V AC ~ ±10% 60Hz / 12V DC 3.5W with Al lens 1/3 inch CCD image sensor 0.194 inch (4.92 mm) horizontal x 0.145 inch (3.69 mm) vertical 510 horizontal x 492 vertical 2:1 interlace NTSC Standard TV system 15.75 KHz horizontal 60 Hz vertical...
Page 14
Power Power consumption Image sensor Image pickup area Effective picture element Scanning system Scanning frequency Synchronization Resolution Minimum illuminance of subject Video output Output impedance White balance Iris control Gain control Backlight compensation Lens mount Ambient temperature Ambient humidity Weight External dimensions Automatic electronic shutter 01_p2-p32...
Product, if it does not perform as warranted. In order to take advantage of this Limited Warranty. You must: (a) call (877) 855-1349 to receive a RMA number: and (b) pay all transportation and insurance charges for shipment of the Product to the ASP or Toshiba Exchange Center.