Sony Xperia TX LT29i Working Instructions
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Cell Phone
  5. Xperia TX LT29i
  6. Working instructions

Sony Xperia TX LT29i Working Instructions

Hide thumbs Also See for Xperia TX LT29i:
Table of Contents

Advertisement

Quick Links

Download this manual
Working Instructions
- mechanical -
Xperia TX
LT29i
1266-4901 Rev 1
Sony Mobile Communications AB – Company Internal

Advertisement

Table of Contents
loading

Related Manuals for Sony Xperia TX LT29i

Summary of Contents for Sony Xperia TX LT29i

  • Page 1 Working Instructions - mechanical - Xperia TX LT29i 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal...

  • Page 2: Table Of Contents

    4.23 Cushion Key Flex ................59 4.24 Key Flex FPC ..................60 4.25 Sub Board Assy ................. 61 4.26 Cushion PBA Main ................63 4.27 Sheet PBA Main .................. 64 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 2(78)
  • Page 3 5.6 Battery ....................76 5.7 Cover Battery Assy ................76 Revision History ................78 For general information about mechanical repair related issues, refer to 1220-1333: Generic Repair Manual - mechanical 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 3(78)

  • Page 4: Exterior Views

    Working Instructions (mech) Exterior Views LT29i 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 4(78)

  • Page 5: Tools

    5. Flex Film Assembly Tool 6. Guitar Pick For part no’s on the tools above, refer to the ‘Tools Catalogue/Matrix’! STANDARD TOOLS 1. Dentist Hook 2. Nylon Pointer 3. Tweezers 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 5(78)

  • Page 6: Disassembly

    Gently pull upwards to unsnap the hooks of the Cover Battery Assy. Remove the Cover Battery Assy. Battery Gently pull upwards to release the Battery with a finger. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 6(78)

  • Page 7: Frame Rear Assy

    Remove the Screw 1.4X3.5 by using a screwdriver with Bits (JCIS No 0). Scrap! Not to be reused! Remove the three Screw M1.4X3.0 by using a screwdriver with Bits (JCIS No 0). Scrap! Not to be reused! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 7(78)
  • Page 8 Insert a Guitar Pick as shown in picture and gently slide along to release the hooks. Do the same to release the bottom side. Do the same to release the hooks on the opposite side. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 8(78)

  • Page 9: Key Flex Fpc

    Remove the Frame Rear Assy. Key Flex FPC Disconnect the BtB connector of the Key Flex FPC by using a Front Opening Tool. Disconnect the second BtB connector. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 9(78)

  • Page 10: Camera

    Remove the Key Flex FPC. Camera Disconnect the BtB connector of the Camera by using a Front Opening Tool. Remove the Camera. Be careful! Do not touch the camera lens! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 10(78)

  • Page 11: Rcv Flex Fpc Assy

    Do the same on the other side as shown in picture. Be careful! Do not damage the earspeaker mesh and the proximity sensor window of the Cover Front Assy! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 11(78)

  • Page 12: Main Pba & Cover Front Assy

    Disconnect the BtB connector by using a Front Opening Tool. Disconnect the second BtB connector. Disconnect this end of the RF Cable by using a Front Opening Tool. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 12(78)
  • Page 13 There are five hooks securing the Main PBA. Insert a Flex Film Assembly Tool as shown in picture and gently pull upwards to release the hooks. Do the same to release the Main PBA. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 13(78)
  • Page 14 Working Instructions (mech) Disassembly Remove the Main PBA. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 14(78)

  • Page 15: Replacement

    Scrap! Not to be reused! INSTALLATION Attach a new Label NFC on its proper position as indicated by the blue rectangle. Press to secure its position and attachment. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 15(78)

  • Page 16: Cover Battery Assy

    Working Instructions (mech) Replacement Cover Battery Assy Follow the 3.1 Disassembly instructions! Prepare a new Cover Battery Assy. Follow the 4.1 installation instructions! Follow the 5.7 Reassembly instructions! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 16(78)

  • Page 17: Label Core Unit

    Label using the ‘‘Label Print Solution’ software. Attach a new Label Core Unit on its proper position and press along to secure its attachment. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 17(78)

  • Page 18: Water Indicator

    Scrap! Not to be reused! INSTALLATION Place a new Water Indicator on the correct position as indicated by the guide line. Press to secure its position and attachment. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 18(78)

  • Page 19: Frame Rear Assy

    Prepare a new Frame Rear Assy. Follow the 4.6, 4.7, 4.8, 4.9, 4.10, 4.11, 4.12, 4.13, 4.14, 4.15 and 4.16 Installation instructions! Follow the 5.5 – 5.7 Reassembly instructions! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 19(78)

  • Page 20: Antenna Nfc

    Scrap! Not to be reused! INSTALLATION Place a new Antenna NFC on its proper position as indicated by the pegs and holes. Press along to secure its position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 20(78)

  • Page 21: Cushion

    Scrap! Not to be reused! INSTALLATION Place a new Cushion on its proper position as indicated by the guiding rectangle. Press along to secure its position and attachment. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 21(78)

  • Page 22: Audio Jack & Adhesive Audio Jack

    Remove it. Detach to remove the Adhesive Audio Jack by using a Flex Film Assembly Tool. Scrap! Not to be reused! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 22(78)
  • Page 23 Place a new Adhesive Audio Jack in the cavity. Press to secure its attachment and position. Peel off the protective film. Place a new Audio Jack in the cavity. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 23(78)
  • Page 24 Working Instructions (mech) Replacement: Audio Jack & Adhesive Audio Jack Press to secure its attachment and position. Be careful! Do not touch the contact pins! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 24(78)

  • Page 25: Vibrator

    Lift up to remove the Vibrator from the cavity by using a Flex Film Assembly Tool. INSTALLATION Place a new Vibrator in the cavity. Press to secure its position. Be careful! Do not touch the contact pins! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 25(78)

  • Page 26: Loudspeaker & Adhesive Speaker

    Detach to remove the Loudspeaker from the cavity by using a pair of Tweezers. Detach to remove the Adhesive Speaker. Scrap! Not to be reused! INSTALLATION Place a new Adhesive Speaker in the cavity. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 26(78)
  • Page 27 Place it in the cavity. Note the orientation of the Loudspeaker to be installed! Press to secure its attachment and position. Be careful! Do not touch the contact pins! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 27(78)

  • Page 28: Cap Rf

    Be careful! Do not damage the RF connector under the Cap RF! INSTALLATION Place a new Cap RF in the hole as indicated by the pointer. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 28(78)
  • Page 29 Working Instructions (mech) Replacement: Cap RF Press along to secure its position. Do the same to the other if need! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 29(78)

  • Page 30: Main Antenna Assy

    Turn the Frame Rear Assy over and lift up to remove the Main Antenna Assy. Scrap! Not to be reused! INSTALLATION Place a new Main Antenna Assy on its proper position as shown. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 30(78)
  • Page 31 Working Instructions (mech) Replacement: Main Antenna Assy Press to secure its attachment and position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 31(78)

  • Page 32: Sub Antenna Assy

    Turn the Frame Rear Assy over and lift up to remove the Sub Antenna Assy. Scrap! Not to be reused! INSTALLATION Place a new Sub Antenna Assy on its proper position as shown. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 32(78)
  • Page 33 Working Instructions (mech) Replacement: Sub Antenna Assy Press to secure its attachment and position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 33(78)

  • Page 34: Key Camera

    Rear Assy as shown. Remove the Key Camera. INSTALLATION Place a new Key Camera into the slot as shown. Note the orientation of the Key Camera to be installed! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 34(78)
  • Page 35 Working Instructions (mech) Replacement: Key Camera Insert the rubber of the Key Camera into the hook of this side as shown. Do the same to the other side. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 35(78)

  • Page 36: Key On/Off

    Rear Assy as shown. Remove the Key On/Off. INSTALLATION Place a new Key On/Off into the slot as shown. Note the orientation of the Key On/Off to be installed! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 36(78)
  • Page 37 Working Instructions (mech) Replacement: Key On/Off Insert the rubber of the Key On/Off into the hook of this side as shown. Do the same to the other side. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 37(78)

  • Page 38: Key Volume

    Rear Assy as shown. Remove the Key Volume. INSTALLATION Place a new Key Volume into the slot as shown. Note the orientation of the Key Volume to be installed! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 38(78)
  • Page 39 Working Instructions (mech) Replacement: Key Volume Insert the rubber of the Key Volume into the hook of this side as shown. Do the same to the other side. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 39(78)

  • Page 40: Camera

    REMOVAL Disconnect the BtB connector of the Camera. Remove the Camera. Be careful! Do not touch the camera lens! INSTALLATION Place a new Camera in the socket. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 40(78)
  • Page 41 Working Instructions (mech) Replacement: Camera Snap the BtB connector. Press to secure its position. Be careful! Do not touch the camera lens! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 41(78)

  • Page 42: Rcv Flex Fpc

    Insert a Front Opening Tool as shown and gently pull upwards to release the RCV Flex FPC Assy from this side. Be careful! Do not damage the Cover Front Assy! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 42(78)
  • Page 43 Unsnap the hook of the RCV Flex FPC Assy. Insert a Front Opening Tool as shown and gently pull upwards to release the Ear Speaker. Scrap the RCV Flex FPC! Not to be reused! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 43(78)
  • Page 44 FPC to be pre-bent as shown in picture. Attach a new Adhesive Earspeaker in the cavity. Press to secure its position and attachment. Peel off the protective film. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 44(78)
  • Page 45 Press to secure its attachment and position. Be careful! Do not touch the contact pins! Turn it over. Press to snap the hook of the RCV Flex FPC Assy. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 45(78)
  • Page 46 Attach a new Cushion Audio Jack 2 on its proper position as shown. Press along to secure its attachment and position. Peel off the protective film. Attach a new Cushion Audio Jack on its proper postion as shown. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 46(78)
  • Page 47 Replacement: RCV Flex FPC Press to secure its attachment and position. Place the new RCV Flex FPC Assy into the cavity. Press to secure its position. Snap the BtB connector. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 47(78)
  • Page 48 Working Instructions (mech) Replacement: RCV Flex FPC Gently insert the key on/off switch into its cavity. Press to secure its position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 48(78)

  • Page 49: Ear Speaker & Adhesive Earspeaker

    REMOVAL Insert a Front Opening Tool as shown and gently pull upwards to release the hook. Detach to remove the Ear Speaker. Detach to remove the Adhesive Earspeaker. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 49(78)
  • Page 50 Attach a new Adhesive Earspeaker in the cavity. Press to secure its position and attachment. Peel off the protective film. Place a new Ear Speaker in the cavity. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 50(78)
  • Page 51 Replacement: Earspeaker & Adhesive Earspeaker Press to secure its attachment and position. Be careful! Do not touch the contact pins! Press to snap the hook of the RCV Flex FPC Assy. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 51(78)

  • Page 52: Cushion Audio Jack

    Scrap! Not to be reused! INSTALLATION Place a new Cushion Audio Jack on the proper position as indicated by the pointer. Press to secure its attachment and position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 52(78)

  • Page 53: Cushion Audio Jack 2

    Scrap! Not to be reused! INSTALLATION Place a new Cushion Audio Jack 2 on the proper position as indicated by the pointer. Press to secure its attachment and position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 53(78)
  • Page 54 Working Instructions (mech) Replacement: Cushion Audio Jack 2 Peel off the protective film. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 54(78)

  • Page 55: Rf Cable

    Gently pull outwards to release the RF Cable from the hook of the Main PBA. Do the same to release it from the hook of the Sub Board Assy. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 55(78)
  • Page 56 Do the same to release it from the second hook. Disconnect this end of the RF Cable and remove it. INSTALLATION Prepare a new RF Cable and the front unit. Snap this end of the RF Cable. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 56(78)
  • Page 57 Push it into the hook of the Sub Board Assy. Do the same to the second hook. Connect this end of the RF Cable. Push it into the hook of Main PBA. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 57(78)
  • Page 58 Replacement: RF Cable Press along to insert the RF Cable into the socket by using a Front Opening Tool. Push the RF Cable as shown to secure its position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 58(78)

  • Page 59: Cushion Key Flex

    Detach to remove the Cushion Key Flex. Scrap! Not to be reused! INSTALLATION Attach a new Cushion Key Flex on its proper position as shown. Press to secure its attachment and position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 59(78)

  • Page 60: Key Flex Fpc

    4.24 Key Flex FPC Follow the 3.1 – 3.4 Disassembly instructions! Prepare a new Key Flex FPC. Follow the 4.23 Installation instructions! Follow the 5.4 – 5.7 Reassembly instructions! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 60(78)

  • Page 61: Sub Board Assy

    Be careful! Do not damage the Sub Board Assy! Do the same on the other side. Be careful! Do not damage the Sub Board Assy! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 61(78)
  • Page 62 Replacement: Sub Board Assy Remove it. INSTALLATION Place a new Sub Board Assy in the cavity. Press to snap the hooks. Be careful! Do not touch the contact pins! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 62(78)

  • Page 63: Cushion Pba Main

    Scrap! Not to be reused! INSTALLATION Place a new Cushion PBA Main on the PBA as indicated by the pointer and the guiding line. Press to secure its attachment and position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 63(78)

  • Page 64: Sheet Pba Main

    Scrap! Not to be reused! INSTALLATION Place a new Sheet PBA Main on the PBA as indicated by the pointer and the guiding line. Press along to secure its attachment and position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 64(78)
  • Page 65 Working Instructions (mech) Replacement: Sub Board Assy Do the same on the opposite side. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 65(78)

  • Page 66: Cover Front Assy

    Follow the 4.25 and 4.22 Installation instructions! Follow the 5.1 – 5.7 Reassembly instructions! Proxy sensor calibration has to be performed for all replaced units; 1262-6643 Trouble Shooting Application – mechanical. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 66(78)

  • Page 67: Board Swap - Replacement

    Build swap for change of label. 4.31 Board Swap – Customize of Software CUSTOMIZE OF SOFTWARE Follow the instructions in the Generic Repair Manual – Build swap for customization of the software. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 67(78)

  • Page 68: Reassembly

    Prepare the Cover Front Assy and the Main PBA. Place the Main PBA on the Cover Front Assembly. Press to snap the hooks. Be careful! Do not touch the pins on the Main PBA! 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 68(78)
  • Page 69 Main PBA. Connect this end of the RF Cable. Press along to insert the RF Cable into the socket. Push the RF Cable as shown to secure its position. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 69(78)

  • Page 70: Rcv Flex Fpc Assy

    Follow the 4.18 Removal and Installation instructions to replace a new RCV Flex FPC Assy! Place the new RCV Flex FPC Assy in the cavity as shown. Press to snap the hooks. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 70(78)

  • Page 71: Camera

    Working Instructions (mech) Reassembly Snap the BtB connector. Gently insert the key on/off switch into its cavity. Press to secure its position. Camera Place the Camera into the socket. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 71(78)

  • Page 72: Key Flex Fpc

    Press to secure its position. Be careful! Do not touch the camera lens! Key Flex FPC Prepare the Key Flex FPC. Securely place it into the socket as shown. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 72(78)
  • Page 73 Working Instructions (mech) Reassembly Snap the BtB connector. Gently insert the key camera switch into its cavity. Press to secure its position. Snap the BtB connector as shown. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 73(78)

  • Page 74: Frame Rear Assy

    Place the Frame Rear Assy on the unit. Press to snap the hooks. Press to snap the hooks of this side. Make sure the hooks securely snapped! Do the same to the opposite side. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 74(78)
  • Page 75 Apply 14 ± 1 Ncm torque when tightening the three screws with Bits (JCIS No 0). Apply 14 ± 1 Ncm torque when tightening the screw with Bits (JCIS No 0). 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 75(78)

  • Page 76: Battery

    Insert the Battery into its socket. Press the bottom of the Battery to secure its position. Cover Battery Assy Place the Cover Battery Assy on the front unit. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 76(78)
  • Page 77 Working Instructions (mech) Reassembly Press to snap the hooks. 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 77(78)

  • Page 78: Revision History

    Working Instructions (mech) Revision History Rev. Date Changes / Comments 2012-Aug-31 Initial release 1266-4901 Rev 1  Sony Mobile Communications AB – Company Internal 78(78)
  • Page 79 Repair Movies - mechanical - Xperia TX LT29i 1266-4996 Rev 1  Sony Mobile Communications AB – Company Internal...
  • Page 80 In that case, right-click with the mouse on the document name and select Save Target As to download the repair movie document for off-line viewing. For general information about repair movies, refer to 1220-1333: Generic Repair Manual - mechanical 1266-4996 Rev 1  Sony Mobile Communications AB – Company Internal 2(4)
  • Page 81 - Cover Front Assy (a) & Main PBA (b) - RCV Flex FPC Assy - Camera - Key Flex FPC - Frame Rear Assy - Battery - Cover Battery Assy 1266-4996 Rev 1  Sony Mobile Communications AB – Company Internal 3(4)
  • Page 82 Repair Movies (mech) Revision History Rev. Date Changes / Comments 2012-Aug-31 Initial release 1266-4996 Rev 1  Sony Mobile Communications AB – Company Internal 4(4)
  • Page 83 Troubleshooting Guide - mechanical - Xperia TX LT29i 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal...
  • Page 84 1.15.1 Compass fails .................... 31 1.16 Accelerometer ..................32 1.16.1 Accelerometer test fails ................32 1.17 Gyroscope ..................33 1.17.1 Gyroscope test fails .................. 33 1.18 Ambient Light Sensor ................ 34 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 2(57)
  • Page 85 1.35 HandsFree by Wire ................54 1.35.1 Connection to Portable HandsFree fails ..........54 1.36 Data Communication ................. 56 1.36.1 Data transfer via System Connector fails ..........56 Revision History ................57 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 3(57)

  • Page 86: Problem Areas

    3. If damaged – replace board. Check: Inspect the Key On/Off (a) and the key on/off switch (b). Action: 1. If dirty – clean them. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 4(57)
  • Page 87 3. If the key on/off switch, the BtB connector or the FPC of the RCV Flex FPC is damaged – replace the RCV Flex FPC. 4. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 5(57)

  • Page 88: Keys

    Inspect the Key Camera (a) and the key camera switch (b). Action: 1. If dirty – clean them. 2. If the Key Camera is damaged – replace it. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 6(57)

  • Page 89: Volume Key

    Inspect the external area of the Key Volume. Action: If dirty – clean it. Check: Inspect the Key Volume (a) and the key volume switch (b). Action: 1. If dirty – clean them. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 7(57)

  • Page 90: On/Off Key

    Inspect the BtB connector of the RCV Flex FPC to the PBA. Action: 1. If not properly connected – disconnect and reconnect. 2. If dirty or oxidized – clean it. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 8(57)
  • Page 91 3. If the key on/off switch, the BtB connector or the FPC of the RCV Flex FPC is damaged – replace the RCV Flex FPC. 4. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 9(57)

  • Page 92: Touch Screen

    2. If dirty or oxidized – clean it. 3. If the touch screen or the FPC of the Cover Front Assy is damaged – replace the Cover Front Assy. 4. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 10(57)

  • Page 93: Display

    2. If dirty or oxidized – clean it. 3. If the display or the FPC of the Cover Front Assy is damaged – replace the Cover Front Assy. 4. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 11(57)

  • Page 94: Led/Illumination

    2. If the external window area is damaged – replace the Cover Front Assy. Check: Inspect the RGB LED on the PBA. Action: 1. If dirty or clogged – clean it. 2. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 12(57)

  • Page 95: Xperia Logo Illumination

    2. If dirty or oxidized – clean the both sides of the BtB connector. 3. If the two BtB connectors or the FPC of Key Flex FPC is damaged – replace the Key Flex FPC. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 13(57)
  • Page 96 1. If dirty – clean it. 2. If the two LEDs or the BtB connector of the Sub Board Assy is damaged – replace the Sub Board Assy. 3. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 14(57)

  • Page 97: Speaker

    Inspect the mesh of the Loudspeaker on the Frame Rear Assy. Action: 1. If dirty – clean it. 2. If the mesh is damaged – replace the Frame Rear Assy. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 15(57)
  • Page 98 2. If dirty or oxidized – clean the both sides of the BtB connector. 3. If the pads or the BtB connector of the Sub Board Assy is damaged – replace the Sub Board Assy. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 16(57)
  • Page 99 2. If dirty or oxidized – clean the both sides of the BtB connector. 3. If the two BtB connectors or the FPC of the Key Flex FPC is damaged – replace the Key Flex FPC. 4. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 17(57)

  • Page 100: Earphone

    Inspect the Ear Speaker’s pins and the pads on the RCV Flex FPC. Action: 1. If dirty – clean them. 2. If the pins are damaged – replace the Ear Speaker. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 18(57)
  • Page 101 2. If dirty or oxidized – clean it. 3. If the pads, the BtB connector or the FPC of the RCV Flex FPC is damaged – replace the RCV Flex FPC. 4. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 19(57)

  • Page 102: Microphone

    Inspect the BtB connector of Key Flex FPC to the Sub Board Assy. Action: 1. If not properly connected – disconnect and reconnect. 2. If dirty or oxidized – clean the both sides of the BtB connector. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 20(57)
  • Page 103 1. If dirty – clean it. 2. If the microphone or the BtB connector of the Sub Board Assy is damaged – replace the Sub Board Assy. 3. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 21(57)

  • Page 104: Secondary Microphone

    Inspect the mesh of the secondary microphone on the Frame Rear Assy. Action: 1. If dirty – clean it. 2. If the mesh is damaged – replace the Frame Rear Assy. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 22(57)
  • Page 105 Troubleshooting Guide (mech) Problem Areas: Microphone Check: Inspect the secondary microphone on the PBA. Action: 1. If dirty – clean it. 2. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 23(57)

  • Page 106: Vibrator

    1. If not properly connected – disconnect and reconnect. 2. If dirty or oxidized – clean it. 3. If the pads or the BtB connector is damaged – replace the RCV Flex FPC. 4. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 24(57)

  • Page 107: Camera

    2. If dirty or oxidized – clean both sides of the BtB connector. Check: Inspect the Camera. Action: 1. If the Camera is damaged – replace it. 2. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 25(57)

  • Page 108: Video Call Camera Defects

    2. If scratched or damaged – replace the Cover Front Assy. Check: Inspect the video camera on the PBA. Action: 1. If dirty or clogged – clean it. 2. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 26(57)

  • Page 109: Flash Led

    2. If the flash LED window scratched or damaged – replace the Frame Rear Assy. Check: Inspect the flash LED on the PBA. Action: 1. If dirty – clean it. 2. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 27(57)

  • Page 110: Bluetooth And Wlan

    Sub Antenna Assy and the contact pins on the PBA. Action: 1. If dirty or oxidized – clean the pads and pins. 2. If the pads are damaged – replace the Sub Antenna Assy. 3. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 28(57)

  • Page 111: Nfc

    1. If dirty or oxidized – clean the pads and pins. 2. If the Antenna FPC or its pads are damaged – replace the Antenna NFC. 3. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 29(57)

  • Page 112: Gps

    Assy and the contact pins on the PBA. Action: 1. If dirty or oxidized – clean the pads and pins. 2. If the pads are damaged – replace the Sub Antenna Assy. 3. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 30(57)

  • Page 113: Compass

    Troubleshooting Guide (mech) Problem Areas 1.15 Compass 1.15.1 Compass fails Action: Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 31(57)

  • Page 114: Accelerometer

    Troubleshooting Guide (mech) Problem Areas 1.16 Accelerometer 1.16.1 Accelerometer test fails Action: Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 32(57)

  • Page 115: Gyroscope

    Troubleshooting Guide (mech) Problem Areas 1.17 Gyroscope 1.17.1 Gyroscope test fails Action: Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 33(57)

  • Page 116: Ambient Light Sensor

    1. If dirty – clean it. 2. If the light sensor or the BtB connector of the RCV Flex FPC is damaged – replace the RCV Flex FPC. 3. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 34(57)

  • Page 117: Proximity Switch

    2. If the BtB connector, the proximity switch or the proximity sensor of the RCV Flex FPC is damaged – replace the RCV Flex FPC. 3. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 35(57)

  • Page 118: Pressure Sensor

    Troubleshooting Guide (mech) Problem Areas 1.20 Pressure Sensor 1.20.1 Pressure Sensor test fails Action: Not applicable. This test is not applicable for this product. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 36(57)

  • Page 119: Water Proof

    Troubleshooting Guide (mech) Problem Areas 1.21 Water Proof 1.21.1 Water Proof fails Action: Not applicable. No water proof functions in the phone. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 37(57)

  • Page 120: Real Time Clock

    Troubleshooting Guide (mech) Problem Areas 1.22 Real Time Clock 1.22.1 Real Time Clock test fails Action: Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 38(57)

  • Page 121: Total Call Time

    Troubleshooting Guide (mech) Problem Areas 1.23 Total call time 1.23.1 Total call time fails Action: Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 39(57)

  • Page 122: External Memory

    If dirty or clogged – clean the external port. Check: Inspect the memory card holder on the PBA. Action: 1. If dirty or clogged – clean the holder. 2. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 40(57)

  • Page 123: Security

    Troubleshooting Guide (mech) Problem Areas 1.25 Security 1.25.1 Security fails Action: Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 41(57)

  • Page 124: Fm Radio

    Inspect the BtB connector of the RCV Flex FPC to the PBA. Action: 1. If not properly connected – disconnect and reconnect. 2. If dirty or oxidized – clean it. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 42(57)
  • Page 125 Problem Areas: FM Radio 3. If the pads or the BtB connector of the RCV Flex FPC is damaged – replace the RCV Flex FPC. 4. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 43(57)

  • Page 126: Flip Slider Counter

    Troubleshooting Guide (mech) Problem Areas 1.27 Flip slider counter 1.27.1 Flip slider counter fails Action: Not applicable. No slider phone. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 44(57)

  • Page 127: Verify Certificates

    Troubleshooting Guide (mech) Problem Areas 1.28 Verify Certificates 1.28.1 Verify certificates fails Action: Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 45(57)

  • Page 128: Irda Test

    Troubleshooting Guide (mech) Problem Areas 1.29 IrDA Test 1.29.1 IrDA test fails Action: . No IrDA in the phone. Not applicable 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 46(57)

  • Page 129: Tv-Out Test

    Troubleshooting Guide (mech) Problem Areas 1.30 TV-Out Test 1.30.1 TV-Out test fails Check: Inspect the USB connector. Action: 1. If dirty or oxidized – clean the connector. 2. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 47(57)

  • Page 130: Connector Ground Test

    Troubleshooting Guide (mech) Problem Areas 1.31 Connector Ground Test 1.31.1 Connector ground test fails Action: Not applicable. This test is not applicable for this product. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 48(57)

  • Page 131: Network & Signal

    Assy and the contact pin on the PBA. Action: 1. If dirty or oxidized – clean the pad and the pin. 2. If the pad is damaged – replace the Sub Antenna Assy. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 49(57)
  • Page 132 Assy and contact pads on the Main Antenna Assy. Action: 1. If dirty or oxidized – clean the pads and pins. 2. If the pads are damaged – replace Main Antenna Assy. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 50(57)
  • Page 133 Inspect the connector of RF Cable to the PBA. Action: 1. If not properly connected – disconnect and reconnect it. 2. If the RF Cable is damaged – replace it. 3. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 51(57)

  • Page 134: Sim

    Check whether the phone is locked to a particular operator and whether the correct operator SIM is being used. Action: 1. Use a proper operator SIM or test SIM. 2. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 52(57)

  • Page 135: Charging

    2. If adhesive is detected on the contact pins – use an eraser to gently rub off the adhesive. Check: Inspect the USB connector. Action: 1. If dirty or oxidized – clean the connector. 2. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 53(57)

  • Page 136: Handsfree By Wire

    Inspect the BtB connector of the RCV Flex FPC to the PBA. Action: 1. If not properly connected – disconnect and reconnect. 2. If dirty or oxidized – clean it. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 54(57)
  • Page 137 Problem Areas: HandsFree by Wire 3. If the pads or the BtB connector of the RCV Flex FPC is damaged – replace the RCV Flex FPC. 4. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 55(57)

  • Page 138: Data Communication

    1.36 Data Communication 1.36.1 Data transfer via System Connector fails Check: Inspect the USB connector. Action: 1. If dirty or oxidized – clean the connector. 2. Replace board. 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 56(57)

  • Page 139: Revision History

    Troubleshooting Guide (mech) Revision History Rev. Date Changes / Comments 2012-Aug-31 Initial release 1266-5087 Rev 1  Sony Mobile Communications AB – Company Internal 57(57)
  • Page 140 Test Instructions - mechanical - Xperia TX LT29i 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal...
  • Page 141 2.2.34 TV-Out Test ....................19 2.3 Manual Tests ..................21 2.3.1 SIM ......................21 2.3.2 On/Off key test ................... 21 2.3.3 Home key test .................... 21 2.3.4 Multitask key test ..................22 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 2(25)
  • Page 142 2.5.2 On-the-air call to mobile (UMTS network available) ....... 24 Revision History ................25 For general information about test procedures, refer to 1220-1333: Generic Repair Manual - mechanical 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 3(25)

  • Page 143: Pre-Test Preparations

    Cover Battery Assy is removed. If affected (red color) - handle the phone according to the local directives. If not affected by liquid, proceed to the „Pre-Test Preparation‟ below. 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 4(25)

  • Page 144: Software

    (see “Service Types” and “Aspects of large files”) In Swap flow, when change a phone from Customer A to Customer B, always use the service Customization script. 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 5(25)

  • Page 145: Tests

    For more information, refer to 1220-1333: Generic Repair Manual - mechanical XPERIA The following pictures will show a simplified basic phone for a general visualization of the service tests! 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 6(25)

  • Page 146: Service Tests

    Make sure that there are no missing segments and that the colors and contrast are OK. XPERIA Press the Back key to return to the Service Test Menu. 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 7(25)

  • Page 147: Led/Illumination

    Sony Ericsson SONY Stereo speaker 2.2.6 Stereo speaker Not applicable, do not use. Left channel is speaking Press the Back key to return to the Service Test Menu. XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 8(25)

  • Page 148: Earphone

    Step 2: Check the quality by listening to the recording from the Speaker during the „Playing recorded sound‟ phase at maximum volume. XPERIA Press the Back key to return to the Service Test Menu. 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 9(25)

  • Page 149: Vibrator

    Aim the camera (located in front of the phone) at an object and check the quality of the image shown in the display. Press the Back key to return to the Service Test Menu. 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 10(25)

  • Page 150: Flash Led

    Device also, when successful, it shows „Test Enable Bluetooth OK Searching Complete‟. Devices found Test Complete Press the Back key to return to the Service Test Menu. XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 11(25)

  • Page 151: Wlan

    Enter into the GPS Location Test and wait for the GPS location data. Press the Back key to return to the Service Test Menu. For GPS testing, refer to 1220-1333: Generic Repair Manual – mechanical XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 12(25)

  • Page 152: Compass

    Front picture. LEFT SIDE Front VIEW BOTTOM VIEW Press the Back key to return to the Service Test Menu. 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 13(25)

  • Page 153: Gyroscope

    Value:45 when the window gets less light. Press the Back key to return to the Service Test Menu. XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 14(25)

  • Page 154: Proximity Switch

    Proximity switch This device does not support the This device does not support the This test is not available for this product! Pressure Sensor function function Water Proof XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 15(25)

  • Page 155: Real Time Clock

    Attach USB Adaptor between phone and an USB disk as shown in picture.  The USB Host Mass Storage status is shown on the screen. XPERIA Press the Back key to return to the Service Test Menu. 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 16(25)

  • Page 156: Security

    2.2.30 Battery Health test Not applicable, do not use. This test is not available for this product! Press the Back key to return to the Service Test Menu. XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 17(25)

  • Page 157: Flip Slider Counter

    Not applicable, do not use. Verify certificates This test is not available for this product! IrDA Test IrDA Test app doesn’t exist IrDA Test app doesn’t exist TV-Out Test XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 18(25)

  • Page 158: Tv-Out Test

    Note: If the TV-Out Monitor doesn‟t automatically indentify the picture, the Monitor may require to set the TV-Out port chosen as source manually in the Monitors menus. Micro USB Cable (Charger/PC) XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 19(25)
  • Page 159 TDMS Status: TDMS Status: On HDCP Status: HDCP Status: On CEC Status: Idle CEC Status: Idle Press the Back key to return to the Service Test Menu. XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 20(25)

  • Page 160: Manual Tests

    2.3.3 Home key test 15:35 Whatever the phone shows now during operation, press the 2010-03-15 Home key for the phone go directly back to the Stand by screen. XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 21(25)

  • Page 161: Multitask Key Test

    - Red: Battery level is between 1% and 10%; - Orange: Battery level is between 11% and 89%; - Green: Battery is between 90% and 100%. XPERIA 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 22(25)

  • Page 162: Battery Test

    After the test the SOMC Battery test.apk shall be removed by tap “Uninstall” “OK” in the application. Error messages are described in the user guide for the SOMC Battery test. 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 23(25)

  • Page 163: Network Test

    Ensure that the UMTS/3G icon now is visible at the top of the display. To verify the radio functions (UMTS) of the phone, follow the „2.4.1.1 Procedure‟ above. 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 24(25)

  • Page 164: Revision History

    Test Instructions (mech) Revision History Rev. Date Changes / Comments 2012-Aug-31 Initial release 2012-Sep-14 Add 2.4 battery test application 1266-5128 Rev 2  Sony Mobile Communications AB – Company Internal 25(25)
  • Page 165 Part List - mechanical - Xperia TX LT29i 1266-5132 Rev 1  Sony Mobile Communications AB – Company Internal...
  • Page 166 Part List (mech) CONTENTS Part List ................... 3 Revision History ................8 1266-5132 Rev 1  Sony Mobile Communications AB – Company Internal 2(8)
  • Page 167 Part No. Part Location Adhesive Audio Jack 1257-4105 Adhesive Earspeaker 1257-6217 Adhesive Speaker 1257-4292 Antenna NFC 1257-0864 Audio Jack 1257-5965 Camera Camera 13M AF 1256-0647 Cap RF 1263-4763 1266-5132 Rev 1  Sony Mobile Communications AB – Company Internal 3(8)
  • Page 168 1264-5360 Cover Front Assy White 1264-5359 Cushion 1263-3122 Cushion Audio Jack 1257-6447 Cushion Audio Jack 2 1262-1946 Cushion Key Flex 1264-5252 Cushion PBA Main 1263-4759 Ear Speaker 1226-7255 1266-5132 Rev 1  Sony Mobile Communications AB – Company Internal 4(8)
  • Page 169 Key Volume Black 1257-4366 Key Volume Pink 1257-7341 Key Volume White 1257-7340 Label Core Unit 1257-6453 Label NFC Label NFC Black 1263-1518 Label NFC White 1264-6322 Loudspeaker Loudspeaker 11x15 1001-0324 1266-5132 Rev 1  Sony Mobile Communications AB – Company Internal 5(8)
  • Page 170 Main Antenna Assy 1257-3743 RCV Flex FPC 1255-3601 RF Cable 1257-7339 Screw 1.4X3.5 1262-1965 Screw M1.4X3.0 1262-3150 Screw Other Len:4.0 Diam:1.4 1227-2716 Sheet PBA Main 1261-4181 Sub Antenna Assy 1257-3759 1266-5132 Rev 1  Sony Mobile Communications AB – Company Internal 6(8)
  • Page 171 Part List (mech) Designation Part No. Part Location Sub Board Assy 1264-5365 Vibrator 1245-2711 Water Indicator 1257-4189 1266-5132 Rev 1  Sony Mobile Communications AB – Company Internal 7(8)
  • Page 172 Part List (mech) Revision History Rev. Date Changes / Comments 2012-Aug-31 Initial release 1266-5132 Rev 1  Sony Mobile Communications AB – Company Internal 8(8)
  • Page 173 Go/No Go Test - electrical - LT29i 1266-5133 Rev 1  Sony Mobile Communications AB – Company Internal...
  • Page 174 Loss Values – Antenna Coupler ..............6 1.3.1 Loss Values – Direct Line ................7 1.3.2 Revision History ................8 This product is ONLY implemented in SERP II 1266-5133 Rev 1  Sony Mobile Communications AB – Company Internal 2(8)

  • Page 175: Go/No Go Testing

    Put the grid positioning holder with its reference point in position G12 and place the phone as shown in the adjacent picture. G H I O P Q R 1266-5133 Rev 1  Sony Mobile Communications AB – Company Internal 3(8)

  • Page 176: Direct Line

    Connect the RF Probe as shown in the adjacent picture. To get access to the RF connector on the PBA, refer to 1266-4901: LT29i Mechanical Working Instructions, Chapter 3.1 and 4.11! 1266-5133 Rev 1  Sony Mobile Communications AB – Company Internal 4(8)
  • Page 177 Follow the directions stated in ‘Go/NoGo Test Script Parameters’ to be found in 1220-1336: Generic Repair Manual – electrical, together with the ‘Attenuation Factors’ below! This phone is available in one version, LT29i, including the following bands: LT29i: GSM-850/900/1800/1900 WCDMA-850/900/1700/1900/2100 1266-5133 Rev 1  Sony Mobile Communications AB – Company Internal 5(8)

  • Page 178: Attenuation Factors

    8.14 High 7.31 6.19 WCDMA 900 High 4.88 12.5 11.77 WCDMA 1700 12.14 High 9.88 14.5 13.4 WCDMA 1900 16.44 High 19.33 16.41 WCDMA 2100 18.01 High 18.11 1266-5133 Rev 1  Sony Mobile Communications AB – Company Internal 6(8)

  • Page 179: Loss Values - Direct Line

    Go/NoGo Testing: Attenuation Factors 1.3.2 Loss Values – Direct Line Attenuation Band Channel GSM 850 GSM 900 GSM 1800 GSM 1900 WCDMA 850 WCDMA 900 WCDMA 1700 WCDMA 1900 WCDMA 2100 1266-5133 Rev 1  Sony Mobile Communications AB – Company Internal 7(8)

  • Page 180: Revision History

    Test and Calibration Repair Instruction Electrical/ Revision History Rev. Date Changes / Comments 2012-Aug-28 Initial release 1266-5133 Rev 1  Sony Mobile Communications AB – Company Internal 8(8)
  • Page 181 Customization - build swap - XperiaTX LT29i 1266-5131 Rev 1 © Sony Mobile Communications AB – Company Internal...
  • Page 182 Customize to Ship ..................6 2.2.2 Build Swap ....................6 Revision History ................7 For general information about Customization and Swap, refer to 1221-5655: Generic Repair Manual – build swap 1266-5131 Rev 1 © Sony Mobile Communications AB – Company Internal 2(7)

  • Page 183: Emma Login & Script Execution

    Activation Script’ you will be prompted for the PIN of your USB Activation Dongle you will be prompted for the PIN of your USB Activation Dongle. 1266-5131 Rev 1 © Sony Mobile Communications AB Sony Mobile Communications AB – Company Internal 3(7)

  • Page 184: Customization Workflow

    Customization Repair Instruction Build Swap Customization Workflow 1266-5131 Rev 1 © Sony Mobile Communications AB – Company Internal 4(7)

  • Page 185: Customize Unit

    User Guide info. http://emma.extranet.sonyericsson.com/documents/emma_user_guide.pdf (see “Service Types” and “Aspects of large files”) In Swap flow, when change a phone from Customer A to Customer B, always use the service Customization script. 1266-5131 Rev 1 © Sony Mobile Communications AB – Company Internal 5(7)

  • Page 186: Customize To Ship Or Build Swap

    Refer to the Cross Reference List for the appropriate variant, which should be based on the non- customizable mechanics of the unit. 2.2.2.2 De-Customize Unit Remove any co-branding as described in 1266-4901: Working Instructions – mechanical 1266-5131 Rev 1 © Sony Mobile Communications AB – Company Internal 6(7)

  • Page 187: Revision History

    Customization Repair Instruction Build Swap Revision History Date Changes / Comments 2012-Aug-31 Initial release 1266-5131 Rev 1 © Sony Mobile Communications AB – Company Internal 7(7)

Table of Contents