Page 1
Digital 4K Video Camera Recorder FDR-AX30 FDR-AX33 FDR-AXP33 FDR-AXP35 SERVICE MANUAL 1st Edition (Revised 1)
Page 2
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 3
Be sure to keep your PC used for service and checking of this 修理時に使用するパソコンは,ウィルス検出ソフトが常にアッ プデートを行っているパソコンを使用してください。もし,修 unit always updated with the latest version of your anti-virus software. In case a virus affected unit was found during service, 理を行うセット,もしくはパソコンがウィルスに感染している 事が判明した場合は,ソニーグループ内は社内技術相談窓口に, contact your Service Headquarters. 特約店様は特約店様専用電話窓口(修理窓口)にご相談くださ い。 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 4
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
Help Guide is an on-line manual. Refer to it for in-depth instructions on the many functions of the camcorder. • Adjust Manual (Available on request) The adjustment software is necessary for adjustment and various checking of this unit for the service. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Abnormality of the drive Turn power off and turn power on again. Continued Function of this code is not provided in this unit. Start the Adjust Manual in the Adjust Station and execute the “Destination data write” on the ADJUST tab. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 18
Replace the board that contains this peripheral circuit. Image vibration correction during The image vibration angular velocity sensor (ROLL SEN- steadyshot does not work. SOR) peripheral circuit may be faulty. Replace the board that contains this peripheral circuit. Continued FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 19
When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items. After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation. Function of this code is not provided in this unit. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Identify the cause of the problem (lens or LD-1017 board), and replace the faulty lens or the LD-1017 board. 1-2-4. E:62:20 Abnormality of Thermistor Check the connection between the lens block and LD-1017 board. Identify the cause of the problem (lens or LD-1017 board), and replace the faulty lens or the LD-1017 board. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
• The proper way to disconnect a connector is to grab the connector instead of the wires. If you pull on the wires, they might be broken. • The proper way to connect a connector is to grab the connector instead of the wires. If you push on the wires, they might be broken. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
• Fixed value (that shows irradiation performance of the projector) • Serial number of the projector unit Method of the data extracting: Start the Adjust Manual in the Adjust Station and execute the “Projector Data Reference” on the DATA tab. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Unless these script files are executed, the following symptoms may appear. Make sure execute the above script files. • The internal memory is not recognized as a media. • The management file saved in the internal memory cannot be repaired. • The internal memory cannot be formatted. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 25
(several seconds later) "SetOverallReadMINI OK" is displayed. Disconnect the USB cable, and turn off the power switch. During the power is turning-on, pull-out the AC-adaptor. Then connect the AC-adaptor Again. The process is executed automatically. (It's running with blue color monitor.) FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
0.05 0.15 Part No. of Shim 4-543-270-01 4-543-270-11 4-543-270-21 4-543-270-31 4-543-270-01 4-543-270-11 4-543-270-21 4-543-270-31 4-543-270-01 4-543-270-11 4-543-270-21 4-543-270-31 P2=0.05 P3=0.035 P1=0.05 (Shim of 0.05 mm is use.) (Shim of 0.035 mm is use.) (Shim of 0.05 mm is use.) FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Self- timer: ON Zoom: Wide end Set the resolving power check chart at shooting distance of 530±20 mm from the filter frame front of the unit. Focus to make the chart aligned equally in all directions at wide end. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 28
• Display the shot image using arbitrary viewer (Windows photo viewer etc.) at the same magnification. Check the image solution. * Check the five patterns in center and four corners at the same magnification. Near the limit NG or out of focus Fig. 2-4-5 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Turn on the power of the unit and enable the Wi-Fi function. (Upon completion of the preparation for Wi-Fi connection, the password for Wi-Fi connection is displayed.) Confirm on the PC or the smartphone that the unit is detected as a connectable wireless network. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj” on the ADJUST tab. Note The sensitivity of the angular velocity sensor is indicated only on the repairing board, but is not indicated on mass production boards. 2-10 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Replace both projector unit (light emitting block) and PJ board. (*1) Projector Data Input Fixed value input Enter the number on the label attached to the unit. Serial number input LD40Syywwnnnnn Enter the red part. Inspect projector LED. ( 1) 2-11 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 32
Replace both projector unit (light emitting block) and PJ board. (*1) Projector Data Input Fixed value input Enter the number on the label attached to the unit. Serial number input LD40Syywwnnnnn Enter the red part. Inspect projector LED. ( 1) Measure brightness. ( 2) 2-12 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
It is the software to adjust and check digital cameras and camcorders for service. The installer of the Adjust Manual and the installation manual are attached, be sure to confirm the contents of them. Note Be sure to install Adjust Station first. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Adjust Station から Adjust Manual を起動し, ADJUST タブにある“PRODUCT ID & USB SERIAL No. INPUT”を実施してください。 2-3-4. リストアデータ (Projector Model) 補修用基板に交換する場合は, 必ず事前に交換前の基板から下記のデータを抽出してください。 • Fixed value (プロジェクターの照射性能を示す値) • Serial number (プロジェクターユニットの製造シリアル番号) データの抽出方法: Adjust Station から Adjust Manual を起動し,DATA タブにある“Projector Data Reference”を実施してく ださい。 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 54
View Position Top View Back View Left View Right View Front View Bottom View The shape may be different from the illustration depending on models. 機種によって形状がイラストと異なる場合があります。 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
The shape may be different from the illustration depending on models. 機種によって形状がイラストと異なる場合があります。 4-2-1. Overall Section-1 • Refer to “Overall Section-1” on exploded view for Ref. No. Non EVF Model EVF Model Claws {5}-2 {5}-2 Claws {5}-3 {6}-1 Overall Section-2 {5}-1 {6}-2 (Note) (Note) (Note) AX30/AXP33/AXP35 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 56
Note When the MM-102 board or FP-2060 flexible board of HDR-AXP33 is troubled, remove the following three parts and abandon them. ・ MM-102 board ・ FP-2060 flexible board ・ Screw Even if without using the three parts, the operation of the set does not have the influence. If these parts are removed, you can not use the demonstration movie. HDR-AXP33のMM-102基板またはFP-2060フレキシブル基板の どちらかが故障した場合は, 下記の3部品を全てセッ トから取り 外して破棄してください。 ・ MM-102基板 ・ FP-2060フレキシブル基板 ・ ネジ 上記3部品は無い場合でも, セッ トの動作に影響はありません。 部品を取り外すとデモ画面は使用できなくなります。 Disassembly Places [1] #2 X 6 Bottom View FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 57
[2] Remove the Belt {1} → #3 X 1 → #2 X 1 Bottom View Left View Claws [3] #3 X 1 Bottom View FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 58
View Finder {5}-3 Bottom View Right View Top View {5}-2 {5}-1 Left View {5}-3 Boss [6] Tilt the View Finder {6}-1, #3 X 1 → Open the Lid {6}-2 , #3 X 1 Back View Bottom View {6}-1 {6}-2 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Be careful not to brake the PHOTO Button. Claw EVF Block Section Non EVF Model EVF Model Claws Unlock the connector, and disconnect the EVF flexible board. ANT901 (Note) #124 Overall Section-3 Note Be careful not to break the NFC Block Assy. NFC部組を折らないよう注意してください。 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 60
Disassembly Places [1] #3 X 2 Top View [2] #2 X 1 Back View [3] #2 X 1, #3 X 3 Top View Top View Case of EVF Model Case of Non EVF Model [5] #2 X 1 Left View FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 61
Arranging the NFC harness NFC harness Fold Insert the creased part of harness into the gap of the Inner Mold (4974) . 15 mm (± 5) NFC harness Inner Mold (4974) Make a habit in a fold on the NFC harness. FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Overall Section-3 • Refer to “Overall Section-3” on exploded view for Ref. No. Claws Claws Claws Claw Claws MIC901 Non Projector Model Overall Section-4 Claw Do not hold lens unit. Claw {2}-1 Projector Model Cabinet (F) Block Section 4-10 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 63
Must not put the lens device (LSV-1550B) turning lens downward. Cabinet (F) Block Downward Disassembly Places [1] #2 X 1 Left View [2] Open the LCD Panel {2}-1, #2 X 2 → Rotate the LCD Panel {2}-2 Back View {2}-1 {2}-2 4-11 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 64
[4] #2 X 2 → #2 X 1 Bottom View Right View Bosses 4-12 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
4-2-4. Overall Section-4 • Refer to “Overall Section-4” on exploded view for Ref. No. (Note 2) (Size: 28 x 9 mm) J901 Overall Section-5 Projector Model LCD Block Section #288 (Note 1) Non Projector Model LCD Block Section 4-13 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 66
[1] Open the LCD Panel {1}, #3 X 1 → #2 X 1, #3 X 1 Front View Right View Notes on Assembling the Overall Section-4 Arranging the USB Conductive Sheet and Tape AS Harness (Red) USB Conductive Sheet Tape AS 3 mm to 5 mm 0 mm to 1 mm 4-14 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
4-2-5. Overall Section-5 • Refer to “Overall Section-5” on exploded view for Ref. No. Overall Section-6 Claws (Note) (Size: 12.5 x 12.5 mm) Note Use this to cut or splice so that it becomes the designated size. 指定のサイズになるように形状を加工して使用してください。 4-15 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 68
[1] #3 X 2 → #12 X 2 Front View Bottom View [2] Remove the two Tapes (AS 1/2) (C) {2}→ #12 X 2 Back View Back View [3] #3 X 3 Bottom View [8] #12 X 1 Back View 4-16 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 69
[9] #3 X 1 Bottom View 4-17 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
4-2-6. Overall Section-6 • Refer to “Overall Section-6” on exploded view for Ref. No. #124 #124 [10] Lens Block ASSY Section Note Notes on Disassembling the Lens Ornament. 4-18 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 71
Push Lock Lens Ornament Disassembly Places [1] #2 X 2 Back View [3] #3 X 1 Bottom View 4-19 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 72
[4] #3 X 2 Top View [5] #3 X 1 Top View [8] #3 X 1 Back View [9] #3 X 3 → #3 X 1 Back View Left View 4-20 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
(Note 3) Note 1 Machining for preventing screws from loosening is applied to this screw. If this screw is turned a few times or more, do not reuse it and use a new one. このねじは緩み防止加工が施されています。 2 〜 3回以上外した場合は, 再利用せず新品のねじを使用して ください。 4-21 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 74
・ フレキシブル基板にしわや折れがある。 Note 7 The Shim (1390) differ in thickness. Make sure to return the removed IM adjust washers to original places. When replacing IM adjust washers, refer to "SELECTION PARTS". Shim (1390) は, それぞれ厚さが異なります。 取り外したIM調整ワッシャは, 必ず元の位置に戻してください。 また, IM調整ワッシャを交換する際は, “SELECTION PARTS”を 参照してください。 4-22 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
(BT4601) on the NK-1001 board. (The battery holder removed once cannot be used again.) When mounting these parts, mount new battery holder first and attach new lithium storage battery next. NK-1001基板のリチウム蓄電池 (BT4601) を交換する場合は バッテリホルダ (BH4601) も同時に新品に交換してください。 (一度使用したバッテリホルダは再使用できません。 ) 部品取り付 けの際は, 先にバッテリホルダを取り付けてから リチウム蓄電池を装着してください。 4-23 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 76
Note 2 This screw can not be reused. Discard the screw removed once in servicing. Instead, use a new screw. このねじは再利用することができません。 サービス対応時に一度でも外した場合は新品のねじと交換 してください。 4-24 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
“EVF Block ASSY Section (EVF Model)” on exploded view for Ref. No. LCD902 Notes on Assembling the EVF Block ASSY Section Attaching the Magnet Install the magnet with the marking oriented as shown in the figure below. Marking 4-25 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
• Refer to “LCD Section (Projector Model)” on exploded view for Ref. No. #288 (Note) LCD901 SP901 Note This screw can not be reused. Discard the screw removed once in servicing. Instead, use a new screw. このねじは再利用することができません。 サービス対応時に一度でも外した場合は新品のねじと交換 してください。 4-26 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 79
Notes on Assembling the LCD Section (Projector Model) Attaching the Magnet Install the magnet with the marking oriented as shown in the figure below. Marking 4-27 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 80
Roll the FP-2296 Flexible Board in the Hinge the Hinge Assy as shown in the Figure below. Cover (M (4974)) as shown in the Figure below. Install the Hinge Cover (C (4974)). Hinge Cover (M (4974)) Hinge ASSY Hinge Cover (C (4974)) FP-2296 Flexible Board 4-28 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Ref. No. #288 (Note 1) LCD901 (Note 2) (Size: 22 x 8 mm) SP901 Note 1 This screw can not be reused. Discard the screw removed once in servicing. Instead, use a new screw. このねじは再利用することができません。 サービス対応時に一度でも外した場合は新品のねじと交換 してください。 4-29 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 82
Use this to cut or splice so that it becomes the designated size. 指定のサイズになるように形状を加工して使用してください。 Notes on Assembling the LCD Section (Non Projector Model) Attaching the Magnet Install the magnet with the marking oriented as shown in the figure below. Marking 4-30 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 83
Roll the FP-2296 Flexible Board in the Hinge the Hinge ASSY as shown in the Figure below. Cover (M (4970)) as shown in the Figure below. Install the Hinge Cover (C (4970)). Hinge ASSY Hinge Cover (M (4970)) Hinge Cover (C (4970)) FP-2296 Flexible Board 4-31 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Removal of Front Ornament Disconnect the two connectors and peel off the Adhesive Parts of the Flexible Board of the Motor A and LF-148 Flexible Board. LF-148 Flexible Board Adhesive Part Connectors Flexible Board of the Motor A Adhesive Parts 4-32 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 85
Remove the six screws and remove the Sheet Metal (C), Mechanical Edge Rubber while detaching the four bosses. Bosses Screw Screw Screw Bosses Sheet Metal (C), Screw Edge of Mechanical Rubber Screw Screw Peel off the Adhesive Parts of the LF-2117 Flexible Board. Adhesive Part LF-2117 Flexible Board 4-33 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 86
Remove the two screws and remove the Frame (F-Sub-A), Frame (F-Sub-B), and Ball Bearing while detaching the two bosses and the shaft. Screw Screw Bosses Frame (F-Sub-A), Frame (F-Sub-B), Ball Bearing Shaft 4-34 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 87
Screw Motor B Remove the four screws and remove the Frame (E-Sub-A), Frame (E-Sub-B), and Ball Bearing while detaching the four bosses and the shaft. Screw Screw Shaft Frame (E-Sub-A), Frame (E-Sub-B), Ball Bearing Bosses Screw Screw Bosses 4-35 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 88
Peel off the Adhesive Part of the Flexible Board of Motor A. Flexible Board of the Motor A Adhesive Part Remove the three screws to detach the Sheet Metal (B), Mechanical Edge Rubber. Sheet Metal (B), Mechanical Edge Rubber Screw Screw Screw 4-36 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 89
Screw Screw Plate of the Motor A Motor A Screw Screw 10. Peel off the Adhesive Part of the LF-2117 Flexible Board and disconnect the connector to remove the LF-2117 Flexible Board. LF-2117 Flexible Board Adhesive Part Connector 4-37 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 90
Polyimide Sheet Screw 13. Remove the screw and remove the five bosses and disconnect the connector to detach the Sheet Metal (D-Sub) and the LF-148 Flexible Board. Boss Screw Boss LF-148 Flexible Board, Sheet Metal (D-Sub) Bosses Boss Connector 4-38 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 91
14. Remove the bond. Bond 15. Remove the screw to detach the Sheet Metal (A). Sheet Metal (A) Screw 16. Remove the boss and the claw to detach the Front Ornament. Boss Claw Front Ornament 4-39 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Install the Sheet Metal (A) and tighten a screw. Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm) Sheet Metal (A) Screw Cut the Polyimide Sheet to the specified length and stick it. 5.0mm 7.0mm Polyimide Sheet 4-40 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 93
Screw (A ): Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm) Screw (B) : Tightening torque = 0.18 ± 0.01N · m (1.8 ± 0.1kg f · cm) Stick the two Polyimide Sheets. Screw (B) Screw (B) Polyimide Sheet Screw (A) Polyimide Sheet Screw (A) 4-41 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 94
LF-148 Flexible Board Adhesive Parts CM Radiation Sheet Shape and sticking position LF-148 Flexible Board sticking direction and of Adhesive Sheet boss positions Bosses Bosses Adhesive Sheets LF-148 Flexible Board 4-42 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 95
Adhesive Sheet as shown in the figure in the frame and then stick it. LF-2117 Flexible Board Adhesive Part Connector Boss positions Shape and sticking position of Adhesive Sheet Bosses Adhesive Sheets 4-43 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 96
Screw (B) : Tightening torque = 0.18 ± 0.01N · m (1.8 ± 0.1kg f · cm) Bosses Cutout Cutout Motor A Motor A Screw (A) Screw (B) Screw Screw Plate of the Motor A Screw Screw (B) 4-44 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 97
If the adhesive force is lowered, cut the Adhesive Sheet as shown in the figure in the frame and then stick it. Shape and sticking position of Adhesive Sheet Adhesive Sheet Flexible Board of the Motor A Bosses Adhesive Part Sheet Metal (B) Flexible Board of the Motor A 4-45 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 98
Plate of the Motor B. Tightening torque = 0.18 ± 0.01N · m (1.8 ± 0.1kg f · cm) Motor B Cutout Motor B Cutout Bosses Screw Screw Screw Screws Plate of the Motor B 4-46 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 99
Ball Bearing Shaft 15. While positioning it with the two bosses, stick the Adhesive Part of the LF-2117 Flexible Board. Adhesive Part LF-2117 Flexible Board Shape and sticking position of Adhesive Sheet Bosses LF-2117 Flexible Board Adhesive Sheet 4-47 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 100
16. While attaching the four bosses, install the Sheet Metal (C) , Mechanical Edge Rubber and then tighten six screws in the order shown in the figure below. Tightening torque = 0.18 ± 0.01N · m (1.8 ± 0.1kg f · cm) Bosses Screw Screw Screw Bosses Sheet Metal (C), Screw Mechanical Edge Rubber Screw Screw 4-48 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 101
LF-148 Flexible Board inside the Sheet Metal (C). LF-148 Flexible Board Adhesive Part Sheet Metal (C) Handling redundant part of Shape and sticking position LF-148 Flexible Board of Adhesive Sheet Sheet Metal (C) LF-148 Flexible Board Adhesive Sheets Redundant part of LF-148 Flexible Board 4-49 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 102
Flexible Board of the Motor A from the center of the Flexible Board to its both ends. Connectors Sheet Metal (C) Flexible Board of the Motor A Adhesive Parts Shape and sticking position of Flexible Board sticking direction Adhesive Sheet Flexible Board of the Motor A Adhesive Sheets Flexible Board of the Motor A 4-50 FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
(SIDE A) (SIDE B) (Page 6-1) (NC) CN2501 LCD901 PROJECTOR (LCD MODULE) UNIT TOUCH CN4505 PANEL PD-1027 BOARD FP-2178 FLEXIBLE BOARD CN4501 BACKLIGHT 3.0 INCH CN4503 WIDE COLOR SP901 VC-1038 (SPEAKER) BOARD (SIDE B) (Page 6-1) FP-2296 FLEXIBLE BOARD FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...
Page 127
Revision History Ver. Date History Contents S.M. Rev. issued 2015.2 Official Release ― ― 2015.3 Revised-1 ・Addition of CEN Model (FDR-AX33). (A1 14-263) FDR-AX30/FDR-AX33/FDR-AXP33/FDR-AXP35...