Page 1
6D114E-5 ENGINE This material is proprietary to Komatsu America Corp. and is not to be reproduced, used, or disclosed except in accordance with written authorization from Komatsu America Corp. It is our policy to improve our products whenever it is possible and practical to do so. We reserve the right to make changes or improvements at any time without incurring any obligation to install such changes on products sold previously.
Page 2
Find manuals at https://best-manuals.com...
Page 3
00 INDEX AND FOREWORD PC360LC-11,PC390LC-11 00-1 Find manuals at https://best-manuals.com...
Page 4
BATTERY DISCONNECT SWITCH ....................10-46 ENGINE SYSTEM ..........................10-47 LAYOUT DRAWING OF ENGINE SYSTEM ................... 10-47 ENGINE CONTROL SYSTEM ....................... 10-49 AUTO-DECELERATION SYSTEM ....................10-52 ENGINE AUTOMATIC WARM-UP SYSTEM .................. 10-54 OVERHEAT PREVENTION SYSTEM .................... 10-56 00-2 PC360LC-11,PC390LC-11 Find manuals at https://best-manuals.com...
Page 5
CONTENTS ............................20-2 ABBREVIATION LIST ..........................20-3 STANDARD VALUE TABLE FOR ENGINE ..................... 20-9 STANDARD VALUE TABLE FOR ENGINE: PC360LC-11, PC390LC-11 .......... 20-9 STANDARD VALUE TABLE FOR MACHINE..................20-14 STANDARD VALUE TABLE FOR MACHINE: PC360LC-11, PC390LC-11 ........20-14 MACHINE POSTURE AND PROCEDURE FOR MEASURING PERFORMANCE ......20-29 STANDARD VALUE TABLE FOR ELECTRICAL ...................
Page 6
PRECAUTIONS FOR CLEANING AND REPLACING KDPF (KCSF and KDOC)......40-141 PREPARATION OF SHORT CIRCUIT ELECTRICAL CONNECTOR (FOR FAILURE CODES [CA1883] AND [CA3135])..........................40-145 FAILURE CODES TABLE ......................40-147 TROUBLESHOOTING BY FAILURE CODE (DISPLAY OF CODE) .............40-164 FAILURE CODE [879AKA]......................40-164 00-4 PC360LC-11,PC390LC-11 Find manuals at https://best-manuals.com...
Page 13
E-17 FUEL GAUGE DISPLAY DOES NOT MOVE FROM MINIMUM OR MAXIMUM ....40-1000 E-18 DISPLAY OF FUEL GAUGE DIFFERS FROM ACTUAL FUEL LEVEL.......40-1002 E-19 ENGINE COOLANT TEMPERATURE GAUGE DISPLAY DOES NOT MOVE FROM MINIMUM OR MAXIMUM.........................40-1003 E-20 DISPLAY OF ENGINE COOLANT TEMPERATURE GAUGE DIFFERS FROM ACTUAL COOL- ANT TEMPERATURE......................40-1004 PC360LC-11,PC390LC-11 00-11...
Page 14
E-55 TRAVEL INDICATOR IS NOT DISPLAYED PROPERLY WITH MONITORING FUNCTION40-1052 E-56 SERVICE INDICATOR IS NOT DISPLAYED PROPERLY WITH MONITORING FUNCTION ................................40-1053 E-57 ATTACHMENT HYDRAULIC CIRCUIT CANNOT BE CHANGED........40-1055 E-58 KOMTRAX SYSTEM DOES NOT OPERATE NORMALLY ..........40-1056 E-59 MACHINE PUSH-UP FUNCTION CANNOT BE CANCELED ..........40-1057 00-12 PC360LC-11,PC390LC-11...
Page 15
S-1 ENGINE DOES NOT CRANK WHEN STARTING SWITCH IS TURNED TO START POSITION...............................40-1130 S-2 ENGINE CRANKS BUT NO EXHAUST GAS COMES OUT ..........40-1131 S-3 FUEL IS BEING INJECTED BUT ENGINE DOES NOT START (MISFIRING: ENGINE CRANKS BUT DOES NOT START) ......................40-1132 S-4 ENGINE STARTABILITY IS POOR..................40-1134 PC360LC-11,PC390LC-11 00-13...
Page 16
DISASSEMBLE AND ASSEMBLE OF KDPF ASSEMBLY ............50-218 REMOVE AND INSTALL SCR ASSEMBLY...................50-227 REMOVE AND INSTALL KDPF, SCR ASSEMBLY................50-233 REMOVE AND INSTALL KDPF, SCR ASSEMBLY BRACKET ............50-247 REMOVE AND INSTALL KCCV ASSEMBLY ................50-255 REMOVE AND INSTALL AdBlue/DEF MIXING TUBE ..............50-258 00-14 PC360LC-11,PC390LC-11...
Page 17
REMOVE AND INSTALL PUMP SWASH PLATE SENSOR ............50-540 REMOVE AND INSTALL MASS AIR FLOW AND TEMPERATURE SENSOR ......50-542 REMOVE AND INSTALL KCCV CRANKCASE PRESSURE SENSOR.........50-544 REMOVE AND INSTALL SCR TEMPERATURE SENSOR ............50-546 REMOVE AND INSTALL REARVIEW CAMERA ................50-549 REMOVE AND INSTALL KOMTRAX TERMINAL ASSEMBLY............50-552 PC360LC-11,PC390LC-11 00-15...
Page 18
COMPONENT PARTS OF AIR CONDITIONER UNIT..............80-21 AIR CONDITIONER CONTROLLER ....................80-25 COMPRESSOR ..........................80-26 CONDENSER ..........................80-27 RECEIVER DRIER......................... 80-28 SENSORS FOR AIR CONDITIONER SYSTEM................80-29 EXPLANATION OF PROCEDURE FOR TESTING AND TROUBLESHOOTING OF AIR CONDITIONER................................80-31 00-16 PC360LC-11,PC390LC-11...
(provides better Sensing System combined operation than OLSS). Engine controller electronically controls supply pump, common rail, and injector. This function Common Rail Injection Engine maintains optimum fuel injection amount and fuel injection timing. PC360LC-11,PC390LC-11 00-19...
Page 22
Technology tronic control and communication. This valve is installed at inlet port of pump, and it adjusts fuel intake amount in order to control fuel Inlet Metering Actuator Engine discharged volume of supply pump. (Same as IMV) 00-20 PC360LC-11,PC390LC-11...
Page 23
Inlet Metering Valve Engine discharged volume of supply pump. (Same as IMA) This mechanism separates oil in blowby gas and Komatsu Closed Crank- KCCV Engine returns it to the intake side to combust it there. It case Ventilation primarily consists of filters.
Page 24
Tip-Over Protectuive chine when it is overtuned.(Hydraulic excavator TOPS Cab and canopy Structure tip-over protective structure) Structure which is standardized as ISO 12117. Solenoid valve that switches over direction of 2-Way Valve Hydraulic system flow. 00-22 PC360LC-11,PC390LC-11...
Page 25
Auxiliary Battery Relay Clockwise Counter Clockwise Electronic Control Unit Electronic Control Module Engine EXGND External Ground F.G. Frame Ground Ground Inlet Metering Actuator No Connection Steering STRG Signal Solenoid Standard Option PRESS Pressure SPEC Specification Switch TEMP Temperature PC360LC-11,PC390LC-11 00-23...
Page 26
ABBREVIATION LIST 00 INDEX AND FOREWORD Abbreviation Actual word spelled out Torque Converter Transmission 00-24 PC360LC-11,PC390LC-11...
REMARK • Some of the attachments and options described in this shop manual may not be available in some areas. If they are required, consult your Komatsu distributor. • The materials and specifications are subject to change without notice. • Shop Manuals are available for "machine part" and "engine part". For the engine unit, see the shop manual for the machine which has the same engine model.
REMARK Remark This signal word contains useful information to know. Unit International System of Units (SI) is used in this manual. For reference, units that have been used in the past are given in { }. 00-26 PC360LC-11,PC390LC-11...
Appropriate servicing and repair are extremely important to ensure safe operation of the machine. The shop manuals describe the effective and safe servicing and repair methods recommended by Komatsu. Some of the servicing and repair methods require the use of special tools designed by Komatsu for special purpos- •...
Then, disconnect the quick release battery terminal (-). REMARK For the machine without the system operating lamp, turn the starting switch to OFF position, wait for two minutes or more before starting the work. Disconnect the quick release battery terminal (-). 00-28 PC360LC-11,PC390LC-11...
Page 31
• Do not use gasoline to wash parts as a general rule. Do not use gasoline to clean electrical parts, in partic- ular. PC360LC-11,PC390LC-11 00-29...
Page 32
• Hanging angle must be 60 ° or smaller as a rule. • When slinging a heavy load (25 kg or heavier), the hanging angle of the rope must be narrower than that of the hook. 00-30 PC360LC-11,PC390LC-11...
Page 33
Precautions for using mobile crane REMARK Read Operation and Maintenance Manual of the crane carefully in advance and operate the crane safely. Precautions for using overhead traveling crane When raising a heavy component (heavier than 25 kg), use a hoist or crane. PC360LC-11,PC390LC-11 00-31...
Page 35
When tightening nuts of the air conditioner hoses and tubes, be sure to use 2 wrenches. Use one wrench to fix and tighten the nut with the other wrench to the specified torque (Use a torque wrench for tightening). PC360LC-11,PC390LC-11 00-33...
Page 36
• The figure shows an example of fitting of O-ring. • An O-ring is fitted to every joint of the air conditioner piping. For tightening torques, see THE OTHER INFORMATION, "Pre- cautions for disconnection and connection of air conditioner piping". 00-34 PC360LC-11,PC390LC-11...
Page 37
Fire around the machine due to highly heated exhaust gas Some models and specifications may be equipped with KDPF (Komatsu Diesel Particulate Filter). KDPF is a system for purifying exhaust gas by removing soot in exhaust gas. In the process of purification (re- generation), the temperature of discharged exhaust gas may be higher than that of conventional models.
Page 38
• When checking fuel, oil, battery electrolyte, or coolant, always use lighting equipment with anti-explosion specifications. • When taking the electrical power for the lighting equipment from the machine, follow the instructions in the Operation and Maintenance Manual. 00-36 PC360LC-11,PC390LC-11...
Page 39
Be sure to wear rubber gloves when handling the materials left after the fire. The material of the gloves, which is recommended is polychloroprene (Neoprene) or polyvinyl chloride (in the lower temperature environment). When wearing cotton work gloves, wear rubber gloves under them. PC360LC-11,PC390LC-11 00-37...
Page 40
Avoid exposure to burning rubber or plastics which produce a toxic gas that is harmful to people. • When disposing of parts made of rubber or plastics (hoses, cables, and harnesses), always comply with the local regulations for disposing industrial waste products. 00-38 PC360LC-11,PC390LC-11...
Page 41
This machine is equipped with the following two exhaust gas treatment systems: • Komatsu Diesel Particulate Filter (hereafter KDPF): A device which captures soot in the exhaust gas to pu- rify exhaust gas. This process performs the combustion of soot referred to as "regeneration".
Page 42
If it gets on your skin, thoroughly wash it off with water. Never relocate or modify the exhaust gas after-treatment device. The harmful gas may be exhausted and it can cause serious damage to the environment as well as violation of laws. 00-40 PC360LC-11,PC390LC-11...
Page 43
If AdBlue/DEF or the machine installed with AdBlue/DEF cannot be stored in the indoors where the temper- ature is at –11 °C or higher (if they are left outdoors in cold weather), AdBlue/DEF in the tank may freeze. Drain AdBlue/DEF to prevent it from freezing. PC360LC-11,PC390LC-11 00-41...
Page 44
Do not discard the oil inconsiderately. Ask the customer for disposal or bring it back to dispose it ap- propriately. REMARK Cover the places tightly with caps, tapes, or plastic bags if it is hard to provide the plugs. 00-42 PC360LC-11,PC390LC-11...
Page 45
Cleaning operation Perform oil cleaning to remove the contaminants and sludges in the hydraulic circuit after repair of the hydraulic device (pump, or control valve) or during operation of the machine. PC360LC-11,PC390LC-11 00-43...
Page 46
PRECAUTIONS FOR HANDLING HYDRAULIC EQUIPMENT 00 INDEX AND FOREWORD REMARK The oil cleaning equipment can remove the ultra fine (approxi- mately 3 μm) particles that the filter built in the hydraulic equip- ment cannot remove. So, it is very effective device. 00-44 PC360LC-11,PC390LC-11...
Page 47
Introduction of parts for the disassembly of the face seal type hoses and tubes Hose side Pipe joint side Nominal No. O-ring (3) Plug (1) Nut (2) 07376-70210 02789-00210 02896-11008 07376-70315 02789-00315 02896-11009 07376-70422 02789-00422 02896-11012 07376-70522 02789-00522 02896-11015 07376-70628 02789-00628 02896-11018 PC360LC-11,PC390LC-11 00-45...
Page 49
Introduction of parts for the removal of O-ring boss type joint Nominal No. Plug (1) O-ring (2) 07040-10807 07002-10823 07040-11007 07002-11023 07040-11209 07002-11223 07040-11409 07002-11423 07040-11612 07002-11623 07040-11812 07002-11823 07040-12012 07002-12034 07040-12412 07002-12434 07041-13012 07002-13034 07040-13316 07002-13334 07041-13612 07002-13634 07040-14220 07002-14234 07040-15223 07002-15234 PC360LC-11,PC390LC-11 00-47...
Page 50
When installing split flanges, tighten the bolts uniformly and alternately to prevent uneven tightening. • As a rule, apply liquid gasket (LG-5) or liquid sealant (LS-2) to the threaded portion of each taper male screws which receive pressure. 00-48 PC360LC-11,PC390LC-11...
Page 51
When the coolant is drained, be sure that the drain valve is securely tightened, then refill the coolant reser- voir with the coolant Komatsu recommends to the specified level. Start the engine to circulate the coolant in the piping, and add the coolant to the specified level again.
Page 52
• Parts which connects the above, or etc. Check that there is no unusual noise by comparing to it of the time when the machine was new. If there is any unusual noise, repair KDPF or muffler, referring to "TROUBLESHOOTING" and "DISASSEMBLY AND ASSEMBLY". 00-50 PC360LC-11,PC390LC-11...
Page 53
The pins of the male and female connectors are attached to wires by crimping or soldering. If excessive force is applied to the wire, the jointed portion (1) may become loose, and it may result in a defective connection or breakage. PC360LC-11,PC390LC-11 00-51...
Page 54
• If there is oil or water in the compressed air, it causes the contacts to become dirtier. Use clean air which any oil and water has been removed from. 00-52 PC360LC-11,PC390LC-11...
Page 55
If a filter oth- er than a Komatsu genuine filter is used, fuel system contamination and damage may occur. Therefore Komatsu recommends using only Komatsu fuel filters and install them following the procedures in the shop manual.
Page 56
Plug the removed pipes and the openings of the removed components with the caps, tapes, plastic bags, etc. to prevent foreign material from entering. NOTICE Do not expose the openings or stuff it, otherwise foreign material may enter it. 00-54 PC360LC-11,PC390LC-11...
Page 57
To propose the periodic inspection (Pm clinic, etc.) according to the service meter reading. How to operate KOMTRAX For the operating method of each screen of KOMTRAX, ask KOMTRAX key person in your Komatsu distributor. PC360LC-11,PC390LC-11 00-55...
Page 58
Provide an oil container to receive a quantity of hydraulic oil which may flow out. Connection Hold hose adapter (1) or hose (5), and insert it in mating adapter (3), aligning the axis. REMARK Do not hold rubber cap portion (4). 00-56 PC360LC-11,PC390LC-11...
Page 59
While keeping the condition of step 1, turn lever (3) to the right (clockwise). While keeping the conditions of steps 1 and 2, pull out whole body (2) to disconnect it. REMARK Provide an container to receive a quantity of hydraulic oil which may flow out. PC360LC-11,PC390LC-11 00-57...
Page 60
While keeping the conditions of steps 1 and 2, pull out whole body (2) to disconnect it. REMARK Provide an container to receive a quantity of hydraulic oil which may flow out. 00-58 PC360LC-11,PC390LC-11...
Page 61
This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...