RXD-M909/LS-M909 ACCESSORIES / CAUTIONS Accessories AM loop antenna (1) FM indoor antenna (1) Video cord (Yellow) (1) (T90-0935-08) (T90-0936-08) (E30-7411-08) Remote control unit (1) Batteries (AAA/R3) (2) RC-F0712E (–) (A70-1744-08) Cautions The marking of products using lasers Manufactured under license from Dolby Laboratories.
RXD-M909/LS-M909 EXTERNAL VIEW Case (A01-4805-08) Jack, RCA (E63-1433-08) Tuner, Analog (W02-4706-08) Connector, Terminal (E21-0044-08) Power cord (E30-7409-08): X (E30-7410-08): E...
Page 4
RXD-M909/LS-M909 PARENTAL LOCK / DISASSEMMBLY FOR REPAIR GUIDE UP/DOWN GEAR LOADING TRAY DISC GEAR PULLEY (L6) SCREW INSERTION (L6) TORGUE CONTROL BASE MAIN (L4) BASE MAIN BELT LOADING (H1) (C2) PWB ASSEMBLY LOADING (S5) (S4) LEVER BASE MAIN (S4) BASE MAIN...
Page 5
RXD-M909/LS-M909 ADJUSTMENT INPUT RECEIVER ALIGNMENT ITEM OUTPUT SETTING ALIGNMENT SETTING FIG. SETTING SETTING POINT Cassette deck Demagnetize heads with the Power: OFF head eraser (Demagnetizer). Demagnetization Heads, capstan Demagnetization Clean heads capstan and pinch and cleaning and pinch roller and cleaning roller using a cotton swab slightly damped with alcohol."...
Page 6
Periphery of IC101 End voltage of IC101 (KIA7042) IC101 is over 5V (KIA7042) (KIA7042) Check voltage of Check if IC101 of output IC100(LC87Fxxx)PIN4 voltage is over4.3V Note: This shooting is the original circuitry so there are some different points from RXD-M909.
Page 7
Voltage 5V. 26pin 2pin data 28pin 1pin clk 26PIN DATA OUT Check DATA INPUT. Check MICOM. Replace MICOM. Replace IC100. Check IC100. FLD light on? Note: This shooting is the original circuitry so there are some different points from RXD-M909.
Check each LINE IC604(PS9830) DATA DATA INPUT PIN23,24,25,26 Resistor output INPUT PWM WAVE Check. Check PWM Modulator output Check FL:PIN75(+),74(-) Replace IC604. IC604(PS9830) FR:PIN71(+),70(-) OTHER OUTPUT Check Note: This shooting is the original circuitry so there are some different points from RXD-M909.
PIN11,12: +3.3V output PIN14:+5V Check Replace IC202. IC202 IC501(ES8390) PIN55 INPUT DATA Check ic201 check CN206 PIN1:SDA IC501(ES8390) PIN8:SDA,PIN9:SCL,PIN10:RST PIN2:SCL DADATA0 OUTPUT PIN6:RST Replace IC201 Note: This shooting is the original circuitry so there are some different points from RXD-M909.
“HIGH”. Check P2203_PIN6,3 input Replace IC202. and PIN8 erase input. Check the Check connector voltage of each pin CN206. on CN202. Check DVD MD Module. Note: This shooting is the original circuitry so there are some different points from RXD-M909.
Check the Tray control I/O Load+ & load- signals Pin on IC401. on P403 are OK? Check the cable connection between DVD PCB and MD (MECHA). Note: This shooting is the original circuitry so there are some different points from RXD-M909.
Page 12
(IC401). properly? properly? Check the cable connection Check cable connection on between P404 and MD. pick-up head. Check RF signal waveform. Disc play? Note: This shooting is the original circuitry so there are some different points from RXD-M909.
Page 13
Check the USB JACK POWER supply. video signal data. Reading OK check (Check CN205,202) Check the USB DATA LINE. (CN202) Check the ES8390. (Check DATA LINE PIN89,90) Note: This shooting is the original circuitry so there are some different points from RXD-M909.
Page 14
1. WHEN POWER ON, RESET & DATA ETC WAVEFORM 3. OPEN/CLOSE WAVEFORM AT POWER ON (OPEN AND CLOSE) RESET(DVD) OPEN(High/Low) SPI_CS3(FLASH) CLOSE(Low/Low) FIG 1 FIG 3 2. WHEN USB FUNCTION OPERATING 4. STARTING ACTION WAVEFORM IN MD DEVICE (SLED HOME) SLO (from MPEG) SLED- SLED+...
5. FOCUS WAVEFORM (IN CASE OF CD/CD-RW/DVD5/DVD-RW) 7. WHEN PUSH OPEN OR STOP KEY ,SPINDLE BREAK SIGNAL (SPNN & SPNP BE USED SPINDLE BREAK DIRECTION) SPNN SPNP FIG 5 FIG 7 6. WHEN DISC READING , SPINDLE KICK SIGNAL 8. AT FIRST ACTION, FOCUS SIGNAL A,B,C,D (SPNN &SPNP BE USED SPINDLE BREAK DIRECTION) SPNN SPNP...
Page 16
9. RF WAVEFORM (ANALOG SCOPE) FIG 9 Note: Refer to Schematic Diagram on waveform’s check point.
RXD-M909/LS-M909 PC BOARD I/O (SIDE A) C004 C003 C002 ZD004 CN001 ZD003 R011 Q002 Q003 Q001 R009 R005 R007 L001 L004 R284 R004 R006 R008 ZD001 VIDEO OUT COMPONENT VIDEO OUT I/O (SIDE B) FRONT VOLUME FRONT JACK CN308 J301...
Page 29
RXD-M909/LS-M909 : WAVEFORM POINT (Refer to Service Manual) P400 HFM VCC HFM VCC RF OUT RF OUT LD DVD LD DVD R414 PU DET MD DVD MD DVD IC401 Q407 PUDET 100K DO1- VR DVD VR DVD DO1+ RFGND GND PD...
Page 32
The DC voltage is an actual reading mea- sured with a high impedance type voltmeter with no signal input. The measurement value may vary depending on the measuring in- struments used or on the product. +12V RXD-M909 (1/4) DVD (4/4)
Page 36
4 5 6 8 9 10 11 12 P7501 C832 C833 330P 330P R825 R826 AGND DVD- CN202 1/4 1 2 3 AGND PN7303 RECORDING LINE SIGNAL LINE GND LINE FRONT- B LINE AU-5 CN303 RXD-M909 (2/4) B LINE MAIN (4/4)
Page 39
DGND DGND DGND RXD-M909 (4/4) The DC voltage is an actual reading measured with a high impedance type voltmeter with no signal input. The measurement value may vary depending on the measuring instruments used or on the product. FRONT (2/2), FRONT VOLUME (1/1), I/O (1/1)
RXD-M909/LS-M909 EXPLODED VIEW (DVD MECHANISM) N09-5611-08 φ2.6x7 N09-5565-08 φ1.7x3 φ2.0x6 (BLK) N89-2006-43 RXD-M909 Parts with the exploded numbers larger than 700 are not supplied.
Page 41
RXD-M909/LS-M909 EXPLODED VIEW (CASSETTE MECHANISM) N86-2005-48 φ2x5 N86-2004-48 φ2x4 N84-2005-48 φ2x5 RXD-M909 Parts with the exploded numbers larger than 700 are not supplied.
Page 42
/CD sync/ SW312 φ3x10 (BLK) : N89-3010-43 SW308 SW307 SW306 clock SW309 SW311 SW302 SW303 SW305 EX.BASS USB/TAPE rec SW310 SW301 VIDEO OUT FRONT JK001 I/O JACK JK303 portable in JK302 volume VR301 JK301 phones SPEAKERS JK701 SMPS MAIN RXD-M909...
Page 44
✽ New parts ✽ New parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 45
✽ New parts ✽ New parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 46
✽ New parts ✽ New parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 47
✽ New parts ✽ New parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 48
✽ New parts ✽ New parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 49
✽ New parts ✽ New parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 50
✽ New parts ✽ New parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 51
✽ New parts ✽ New parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
(Cr-signal) ............0.680 Vp-p (75 Ω) USB interface Notes: Format ........USB host (Playing back/Recording) • Kenwood follows a policy of continuous advancements in Supported devices ....USB mass storage class device development. For this reason specifi cations may be changed Interface ............USB 2.0 (Full speed)/1.1 without notice.