In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts.
CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazardous 2. The only source of X-RAY RADIATION in this TV receiver X-RAY RADIATION.
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL. SET-UP ADJUSTMENT R The following adjustments should be made when a complete realignment is required or a new picture tube is installed. Perform the adjustments in order as follows : 1.
Page 5
(5) Adjust the sub-4-pole magnets only in case there is any deviation of Xv bow-shaped convergence. (To be usually set at the initial position) Align both sides with the sub-4-pole magnets and minimize the deviation of blue and red with the main 4-pole magnets. Xv bow-shaped deviation of convergence red/blue blue...
SERVICE MODE 1. ENTERING TO SERVICE MODE 1) Press o button once on 2) Press o button again to 3) While pressing the o button, Remote Control. keep pressing. press MENU button on TV set. Item Data or Sound Mute (Service mode display) 2.
Page 7
4. SELECTING THE ADJUSTING ITEMS 1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) Refer to table-2 for preset data of adjustment mode. (See SETTING & ADJUSTING DATA on page 16) 5.
Page 8
8. SELF DIAGNOSTIC FUNCTION 1) Press “9” button on Remote Control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC’s are executed properly. 2) During diagnosis, the following displays are shown. JH9_000 34JZ9UE 1 Firmware:...
DESIGN MODE 1. ENTERING TO DESIGN MODE 1) Select the Service mode. 2) While pressing CALL button on Remote 3) The following displays and press MENU button on TV. are shown on the screen. Press Press JH9_039 (Design mode) Version information of microprocessor Main tuner information Sub tuner information...
ELECTRICAL ADJUSTMENTS ITEM ADJUSTMENT PROCEDURE FOCUS VR ADJ 1. Enter the service mode, then select any register item. 2. Press the a button on the Remote until the black cross-bar pattern appears on the screen. 3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture screen.
Page 11
ITEM ADJUSTMENT PROCEDURE WIDTH 1. Call up the adjustment mode display, then select the item WID. (WID) 2. Press the ; – /+ button to get the picture so the left and rightedges of raster begins to lack. 3. Press the ; – /+ button to advance the data by 7 steps. Note: Check the horizontal picture position is correct.
Page 12
V/C system adjustment ADJUSTING ITEMS ADJUSTMENT PROCEDURE REMARKS AND POINTS Cutoff adjustment and 1) Setting to horizontal alignment, turn the screen VR to No outside lighting shall white balance adjust- stop where the brightness lines are slightly luminous. be allowed. ment (Adjustment shall be made so that they look almost Measurement shall be...
Page 13
* Deflection adjustment shall be made from PAL/100 Hz/WIDE mode. Horizontal adjustment ADJUSTING ITEMS ADJUSTMENT PROCEDURE AND POINTS Hori- For PAL/100 Hz/WIDE <Adjustment condition> zontal Horizontal amplitude Horizontal adjustment shall be made using E-12CH Philips pattern and DYNAMIC (WID) image mode. Side pin distortion (PARA) <Adjustment procedure>...
Page 14
Vertical adjustment ADJUSTING ITEMS ADJUSTMENT PROCEDURE AND POINTS Verti- For PAL WIDE 1) With E-12ch, WIDE mode, DYNAMIC and 100 Hz, adjust the vertical screen Vertical amplitude position (VPOS) and amplitude (HIT) as shown in the following figure: (HIT) Vertical screen position Flags shall just be blinded.
CIRCUIT CHECK HIGH VOLTAGE CHECK CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps below. 1. Connect an accurate high voltage meter to the second anode of the picture tube. 2. Turn on the receiver. Set the BRIGHTNESS and CONTRAST controls to minimum (zero beam current). 3.
PROGRAMMING CHANNEL MEMORY • First, use the Auto tuning to preset all the active channels in your area automatically. Then, arrange the preset channels with the Manual tuning so that you can tune into only desired channels. • Use the Manual tuning if desired channels cannot be preset with the Auto turing or if you would like to preset channels to specific position numbers one by one.
Page 20
D. Program position skip selection Press the button to turn the program position skip option on “ ” or off “ ”. The program position will then be skipped when you select program positions with the CHs or CHt button. “...
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. • The PC board assembly with mark is no longer available after the end of the production. Model: 29CZ9UE/29CZ9UES Capacitors ..CD Ceramic Disk Plastic Film Electrolytic Resistors ....
Page 22
Location Parts No. Description Location Parts No. Description C661 76206229 ELECTROLYTIC 50V 2.2UF M 7L 3A C893 76092337 CERAMIC DISC 2KV 220PF K C662 76206229 ELECTROLYTIC 50V 2.2UF M 7L 3A C895 76766102 ELECTROLYTIC 50V 1000UF M C663 76591102 PLASTIC FILM 50V 1000PF J C896 76214471 CERAMIC DISC 500V B 470PF K...
Page 23
Location Parts No. Description Location Parts No. Description CV23 76092731 CERAMIC CHIP 16V B 1UF K R371 76011103 CHIP 1/20W 10K OHM J CV24 76100104 CERAMIC CHIP 25V F 0.1UF Z R372 76011103 CHIP 1/20W 10K OHM J CV25 76100104 CERAMIC CHIP 25V F 0.1UF Z R373 76011102...
Page 24
Location Parts No. Description Location Parts No. Description R604 76000445 CHIP JUMPER 1608TYPE R803 76554333 OXIDE METAL FILM 2W 33K OHM J R605 76011103 CHIP 1/20W 10K OHM J R805 76552391 OXIDE METAL FILM 1/2W 390 OHM J R606 76011103 CHIP 1/20W 10K OHM J R806 76381223...
Page 25
Location Parts No. Description Location Parts No. Description R996 76383153 OXIDE METAL FILM 2W 15K OHM J RS82 76011101 CHIP 1/20W 100 OHM J RA71 76366683 CARBON FILM 1/6W 68K OHM J RS83 76011101 CHIP 1/20W 100 OHM J RA72 76366223 CARBON FILM 1/6W 22K OHM J RV01...
Page 37
SPECIFIC INFORMATIONS SCHEMATIC DIAGRAM MODEL : 29CZ9UE/29CZ9UES WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAUSTION” AND “PRODUCT SAFETY NOTICE” ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols “ ” in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
SPECIFICATIONS MODEL 29CZ9UE/29CZ9UES Rated voltage g 110 V – 240 V, 50/60 Hz Power consumption 185 W (at g 220 V, 50 Hz) Dimensions 782.1 mm (W) × 492.5 mm (D) × 585.1 mm (H) (Width × Depth × Height) Mass (Weight) 45.1 kg...
Page 42
SPECIFIC INFORMATIONS SCHEMATIC DIAGRAM MODEL : 29CZ9UE/29CZ9UES WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAUSTION” AND “PRODUCT SAFETY NOTICE” ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols “ ” in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 89
U901A L801Z L802Z OPEN OPEN L801 L802 TPW2064AL/TPW2058AS TPW2064AL/TPW2058AS P804B Lock 2P_11.88mm_S GJ16 OPEN GJ14 OPEN OPEN OPEN GJ17 GJ15 29CZ9UE/29CZ9UES CRT-D/SVM CHOKE COIL (45/54)
Page 90
RXD_EXT 5V1_EXT 7-C3 TO CONTROL BOARD TXD_EXT IF_GND RXD_EXT P018B 3P_2.5mm_1.5A_Beige 7-B5 7-B5 GND_AUDIO GND_AUDIO GND_AUDIO 7-B5 27V_AUDIO 27V_AUDIO 27V_AUDIO 7-B5 7-B5 P805 CON 1P TO B/M MODULE TO PC/D TERMINAL TO PC/D TERMINAL 29CZ9UE/29CZ9UES AV TERMINAL (1/7) SHEET-1/7 (46/54)
Page 91
Q4103 2SC4667 2SC4081-Q G_PC R4102 R4107 G_PC R4104 R4109 Q4102 2SC4081-Q R4123 R4121 B_PC 2.2k B_PC 2.2k Q4100 2SC4667 R_PC R_PC VS_PC VS_PC HS_PC HS_PC GRV01 OPEN GRV02 OPEN GRV03 OPEN GRV04 OPEN 29CZ9UE/29CZ9UES AV TERMINAL (V SW) SHEET-2/7 (47/54)
Page 97
TLB018 TLB019 TLB021 TLB026 TLB027 TLB030 TLB032 TLB034 TLB036 TLB037 TLB039 TLB040 TLB041 TLB042 TLB043 FROM POW/DEF TO POW/DEF POWER/DEF BOARD HYPER SIGNAL BOARD HYPER SIGNAL BOARD AV TERMINAL BOARD AV TERMINAL BOARD BB07/BB08 OR P018A/P019A 29CZ9UE/29CZ9UES UNIT FRONT (53/54)