Initial Settings Of This Receiver; Setting With A Special Application (Start-Up Navi); Perform Settings Using The Avnavigator Built Into This Receiver - Pioneer Elite SC-99 Operating Instructions Manual

04

Initial settings of this receiver

There are three ways to initialize this receiver.
!

Setting with a special application (Start-up Navi)

!

Perform settings using the AVNavigator built into this receiver

! Setting by referring to the operating instructions
Important
! After unpacking, turning on the power, and returning to initial factory settings
indicator slowly flashes. This is not a malfunction.
! This receiver is designed to automatically enter WAC mode when turning on the power of this receiver in the
initial factory settings state. For details about WAC mode, please refer to
(page 53 ) have been completed, the WIRELESS indicator flashing disappears.
! When using the receiver without connecting to the network, set the Network Type setting to Wired
54 ).

Setting with a special application (Start-up Navi)

If you have a smart phone or tablet, once you download and start the special application, the settings can be done
according to the instructions by the application.
! For those using an iPad, iPhone, or iPod touch
! If you have an Android device

Perform settings using the AVNavigator built into this receiver

If you have a Windows PC or Mac, the settings can be performed using the AVNavigator built into this receiver.
How to use the built-in AVNavigator
The built-in AVNavigator is equipped with Wiring Navi, which allows you to perform connection of this receiver
and initial settings in interactive mode. By simply following the screen prompts to connect and set the unit, highly
accurate initial settings can be performed easily.
Additionally, in order to use various functions easily, contents linked to the receiver can be used.
on page 51
on page 51
on page 53
(page 97 ), the WIRELESS
page 55 . After the network settings
Operating Environment
! AVNavigator can be used in the following environments.
— Windows PC: Microsoft ® Windows Vista
— Mac: OS X v 10.9 or 10.8
— iPad/iPhone/iPod touch: iOS 6.1 or later
— Android operation confirmation device:
SONY XPERIA Z1 (OS 4.2.2)
SAMSUNG GALAXY S5 (OS 4.4.2)
HTC One S (OS 4.1.1)
Google Nexus 5 (OS 4.4.4)
! AVNavigator uses an Internet browser. The following browsers are supported:
— Windows PC: Internet Explorer
— Mac/iPad/iPhone/iPod touch: Safari 6.0, 7.0
— Android device: Android browser
(page
! Depending on the computer network setting or security setting, AVNavigator may not operate.
Using AVNavigator
Important
! Connect the LAN terminal to the network
! When the WIRELESS indicator blinks slowly, AVNavigator cannot be started. WAC Mode is on in this case.
Refer to page 55 for information about WAC Mode. Turn this receiver's power off, and then turn it on again
after re-attaching the LAN cable.
1 Press u STANDBY/ON to switch on the receiver and your computer.
2 Launch AVNavigator.
Operate AVNavigator by following the screen prompts of your computer, etc.
! If using a Windows PC, complete the below steps to start up.
1 Start up Internet Explorer on your PC (open any random Internet page).
2 Press STATUS on the remote control and check the front panel display on the receiver (the IP address of
the receiver will appear).
If 0.0.0.0, 192.168.1.1 or 169.254.112.202 appears in the address, it indicates that the receiver is not con-
nected to the network. Check to make sure that the receiver and router are properly connected.
3 Enter number in 2 above in the field in Internet Explorer shown below and then press the ENTER key.
51
® /Windows ® 7/Windows ® 8/Windows ® 8.1
® 8, 9, 10, 11
(page 47 ).
(Example Text Display)
(Example Input Format) 192.168.0.124
Basic Setup