Page 1
BA-5 SERVICE MANUAL CHASSIS MODEL COMMANDER DEST CHASSIS NO. KV-29FS12A RM-Y168 SCC-S38T-A KV-29FS12A RM-Y168 ® TRINITRON COLOR TV...
Page 2
KV-29FS12A SPECIFICATIONS KV-29FS12A Power requirements 120V/220V, 60Hz/50Hz Number of inputs/outputs Video S Video Audio Audio Out Y, P Speaker output(W) 10Wx2 Power Consumption(W) In use(Max) 185W In standby Dimensions(W/H/D) 700 x 632 x 512 mm. (mm) x 24 x 20 (in) Mass (kg)
SECURITE DU FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES SONY PARTS WHOSE PART NUMBERS APPEAR AS COMPOSANTS SONY DONT LE NUMERO DE PIECE EST INDIQUE DANS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS LE PRESENT MANUEL OU DANS DES SUPPLEMENTS PUBLIES PAR SONY.
Page 5
KV-29FS12A Display of Standby/Timer LED Flash Count 2 times 4 times 5 times LED ON 0.3 sec. STANDBY/TIMER LED LED OFF LED OFF 0.3 sec. 3 sec. Diagnostic Item Flash Count* +B overcurrent 2 times I-Prot 4 times 5 times *One flash count is not used for self-diagnostic.
Page 6
KV-29FS12A Handling of Self-Diagnostic Screen Display Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”. Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.
KV-29FS12A SAFETY CHECK-OUT After correcting the original service problem, perform the Leakage Test following safety checks before releasing the set to the The AC leakage from any exposed metal part to earth customer: ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 1.
AUX and normal (CATV) input, you should consider using the Channel Fix feature, (see page 26). Your Sony remote control can be programmed to operate your cable box, (see page 36). If you are connecting to an indoor or outdoor antenna, you may need to When using PIP, you cannot view the AUX input in the window picture.
Page 9
Connecting Your TV Operating Instructions Connecting Additional Equipment TV and Cable Box TV and VCR Cable Box Rear of TV Rear of TV From cable Connect the coaxial cable from your cable service to the IN jack on From your cable box. cable/ antenna Connect a coaxial cable (not supplied) from the OUT jack on your...
Page 10
Connecting Your TV Operating Instructions TV, Cable box, and Cable TV, VCR, and Cable box KV-27FS16, KV-27FV16, KV-32FS16, KV-29FV16 only Rear of TV For this set up, you can switch between scrambled channels (through your cable box) and normal (CATV) channels by pressing Rear of TV (KV-27FV16 only) Cable Box Cable box...
Page 11
Connecting Your TV Operating Instructions TV and Satellite Receiver TV, Satellite Receiver, and VCR Satellite Rear of TV antenna cable Rear of TV From From cable/ cable/ antenna antenna SATELLITE IN VHF/UHF AUDIO R AUDIO L VIDEO AUDIO R AUDIO L VIDEO Satellite receiver VHF/UHF LINE IN...
Page 12
Brings up the custom guide of sound. your satellite receiver. MENU Displays the on-screen menu. SYSTEM Powers off all Sony equipment at Press again to exit the menu at once, (may not work with older any time. equipment). RESET Press to return to factory settings...
Page 13
If, after reading these Operating Instructions, you have additional questions related to the use of your Some electronic equipment can create electrical noise, Sony television, please call our Direct Response Center at 1-800-222-SONY (7669) (U.S. residents which can interfere with TV reception.
KV-29FS12A 2-4. PICTURE TUBE REMOVAL WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.
KV-29FS12A SECTION 3 SET-UP ADJUSTMENTS The following adjustments should be made when Perform the adjustments in order as follows: a complete realignment is required or when a new 1. Beam Landing picture tube is installed. 2. Convergence 3. Focus These adjustments should be performed with rated 4.
KV-29FS12A 3-2. CONVERGENCE Horizontal Static Convergence Before starting convergence adjustments: If the blue dot does not converge with the red and green dots, perform the following: 1. Perform FOCUS, V.LIN AND V.SIZE adjustments. 1. Move BMC magnet (a) to correct insufficient H. Static 2.
KV-29FS12A 4. Adjust XCV core to balance X axis. 5. Adjust YCH VR to balance Y axis. * / 4 6. Adjust vertical red and blue convergence with V.TILT 4 / * (TLV VR). 4 / * * / 4 Note: Perform adjustments 3-6 while tracking items 1 and 2.
KV-29FS12A 3-4. SCREEN (G2) 3-6. WHITE BALANCE ADJUSTMENTS 1. Input a dots pattern. 1. Input an entire white signal with burst. 2. Set the PICTURE and BRIGHTNESS controls at minimum 2. Set to Service Adjustment Mode. and COLOR control at normal. 3.
KV-29FS12A SECTION 4 SAFETY RELATED ADJUSTMENTS 4-1. R564 CONFIRMATION METHOD Hold-Down Readjustment (HV HOLD-DOWN CONFIRMATION) AND If the setting indicated in Step 2 of Hold-Down Operation READJUSTMENTS Confirmation cannot be met, readjustment should be performed by altering the resistance value of R564 component marked with The following adjustments should always be performed when replacing the following components which are marked with T505...
KV-29FS12A SECTION 5 CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER Use the Remote Commander (RM-Y168) to perform the circuit adjustments in this section. NOTE: Test Equipment Required: • Pattern generator • Frequency counter • Digital multimeter • Audio oscillator 5-1. SETTING THE SERVICE ADJUSTMENT MODE 5-2.
Page 23
KV-29FS12A Adjustment Items AVERAGE Reg # ITEM FUNCTION RANGE DATA NTSC PAL M PAL N VIDEO DATA HSIZ Horizontal Size Adjustment 0-63 HPOS Horizontal Position Adjustment 0-63 VBOW Vertical Line Bowing Adj. 0-15 VANG Vertical Line Bowing Slant Adj. 0-15 VTRP TRAPEZIUM 0-31...
Page 24
KV-29FS12A AVERAGE Reg # ITEM FUNCTION RANGE DATA NTSC PAL M PAL N VIDEO DATA PDSO PDS OFF 0-15 HPKO HPK OFF Palette CORE CORE TRAP TRAP CHTR CH TRAP CBPF CBPF ENHO ENHOFF NMRD NMRD YAPS YAPS CLKS CLKS NSTD NSTDS KILS...
Page 25
KV-29FS12A AVERAGE Reg # ITEM FUNCTION RANGE DATA NTSC PAL M PAL N VIDEO DATA PACS SET_ACC PSDL SYNC_DELAY PDCO PCGA C_GAIN PAAF PSU2 PCVF PBIT BITSEL PAFC AFCBITSEL PACC ACC_LEVEL 0-63 PBUR BURST_CLK PEVE EVENUPRA PINW INV_WFF PINR INV_REF PREF RFF_FIX PARE...
KV-29FS12A 5-4. MA BOARD ADJUSTMENTS 3. Select DISP with 4. Adjust values of DISP with to adjust characters H. Frequency (Free Run) Check to the center. 1. Input a TV mode (RF) with no signal. 5. Write to memory by pressing then 2.
Page 27
KV-29FS12A V. Center Adjustment (VPOS) V LINEARITY (VLIN) Perform this adjustment after performing H. Frequency (Free Run) Check. 1. Input a crosshatch signal. 2. Activate the Service Adjustment Mode. V CORRECTION (SCOR) 3. Select the VPOS item with 4. Adjust value of VPOS with for the best vertical center.
Page 35
KV-29FS12A A Board Schematic Diagram CN460 TO K BOARD CN450 STEREO TU101 J205 FSS BTF-WA412 YCBCR AUDIO IC402 TP100 TUNER INPUT TDA8580Q/N1 RF-AGC R430 AUDIO AMP A BOARD IC VOLTAGE LIST TP102 C219 C215 R107 DET OUT R421 R429 CN2005 :CHIP AUDIO R 4.7k...
Page 36
KV-29FS12A MA Board Schematic Diagram CN005 CN006 CN004 CN003 TO A BOARD TO A BOARD TO A BOARD TO A BOARD MA BOARD IC VOLTAGE LIST CN2005 CN2006 CN2007 CN2008 IC001 IC003 IC302 volt volt volt Q003 VIDEO 2SD601A BUFFER All voltages are in V R308 R042...
Page 37
KV-29FS12A MA BOARD IC BLOCK DIAGRAM MA BOARD: IC301 CXA2155S [TUNING CONTROL, Y/C/J] MA BOARD LOCATOR LIST DIODE Q303 D001 Q305 D002 Q310 HX Board Schematic Diagram D003 Q349 D004 Q350 D005 Q351 D006 Q352 (KEY) D075 Q354 D301 Q355 D305 Q356 CN4001...
Page 38
KV-29FS12A CA Board Schematic Diagram [RGB DRIVE, CRT DRIVE] R717 CN704 TO A BOARD R716 100k (T505) 1/2W FOCUS J701 TO A BOARD (T505) G4 HV KR G1 G1-1 C707 0.0047 RV701 VSTAT CONTROL 110M G1-3 G1-2 200V CA BOARD WAVEFORMS R715 560k CN702...
Page 40
KV-29FS12A D Board Schematic Diagram D BOARD TRANSISTOR CN801 VOLTAGE LIST VOLTAGE LIST TO VA BOARD CN904 Q801 Q806 volt volt -2.2 Q802 Q809 R875 volt volt :CHIP R869 R870 100k R874 2.2k :CHIP :CHIP :CHIP C825 R867 R815 0.01 R871 R819 680k...
* A-1343-875-A D (VAR) MOUNTED PC BOARD 4-075-658-01 DOOR 1-783-838-31 CORD, POWER (WITH CONNECTOR) 4-047-464-01 CATCHER, PUSH * A-1380-632-A K (VAR) MOUNTED PC BOARD 3-704-179-31 EMBLEM (NO.9), SONY 1-766-374-11 PLUG, F-PIN 4-075-657-11 GUIDE, LED 4-075-652-11 COVER, REAR 4-068-982-02 MULTI-BUTTON (TOP)
KV-29FS12A SECTION 8 ELECTRICAL PARTS LIST Note: The components identified by in this manual have been carefully factory-selected for each set in The components identified by shading order to satisfy regulations regarding X-ray and mark are critical for safety. Replace radiation.
Page 44
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 45
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 46
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 47
KV-29FS12A Note: Note: The components identified by in this manual have been The components identified by shading carefully factory-selected for each set in order to satisfy regu- and mark are critical for safety. Replace lations regarding x-ray radiation. Should replacement be required, only with part number specified.
Page 48
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 49
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 50
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 51
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 52
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 53
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 54
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 55
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 56
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 57
KV-29FS12A Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 58
* 4-074-566-01 CUSHION ASSY, FRONT (UPPER) * 4-074-567-01 CUSHION ASSY, LOWER REMOTE COMMANDER 1-418-387-11 REMOTE COMMANDER (RM-Y168) 4-978-977-01 BATTERY COVER FOR RM-Y168 Sony Corporation English Sony Technology Center 2000GS74060-1 Technical Services Printed in USA 9-965-892-01 Service Promotion Dept. 2000.6 — 74 —...