en Safety Safety Observe the following safety instructions. General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. Intended use Only use this appliance: ¡...
Page 5
Safety en WARNING ‒ Risk of electric shock! ¡ Incorrect installation is dangerous. ▶ Connect and operate the appliance only in accordance with the specifications on the rating plate. ▶ Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating current only via a properly installed socket with earthing.
en Safety WARNING ‒ Risk of injury! Hinges move when opening and closing the appliance door and can cause injury. ▶ If built-under or integrable appliances are not in a cavity so that one side is accessible, the hinge area must be covered at the side.
Page 7
Safety en WARNING ‒ Risk of injury! ¡ Leaving the appliance door open may result in injury. ▶ Only open the appliance door to load or unload tableware in order to prevent accidents, e.g. through tripping. ▶ Do not sit or stand on the appliance door when open. ¡...
en Safety Damaged appliance WARNING ‒ Risk of electric shock! ¡ If the appliance or the power cord is damaged, this is danger- ous. ▶ Never operate a damaged appliance. ▶ Never operate an appliance with a cracked or fractured sur- face. ▶ Never pull on the power cord to unplug the appliance. Al- ways unplug the appliance at the mains.
Safety en WARNING ‒ Risk of harm to health! Children can lock themselves in the appliance, thereby putting their lives at risk. ▶ With redundant appliances, unplug the power cord. Then cut through the cord and damage the lock on the appliance door beyond repair so that the appliance door will no longer close.
en Preventing material damage Only use the water hoses sup- ▶ Preventing material damage Preventing material dam- plied with the appliance or genu- ine spare hoses. Never re-use water hoses that ▶ have been used before. Preventing material damage Safe installation ¡...
Childproof lock en To prevent corrosion, do not use ▶ Environmental protection and saving energy Environmental protection sponge cloths on dishwashers with a stainless steel front or and saving energy rinse such cloths thoroughly several times before using them Environmental protection and saving energy for the first time.
en Environmental protection and saving energy During the drying phase moisture Sensor setting Description from the interior of the dishwasher is Standard Optimum setting for a stored in the mineral and heat energy mixed load and heavily is released. The heat energy is blown soiled tableware.
Installation and connection en installing it under a continuous work- Installation and connection Installation and connec- top that is securely connected to ad- jacent cabinets. tion "Follow the safety instructions." To ensure proper operation, connect Installation and connection → Page 4 the appliance to the power and water "Follow the instructions for elec- supply correctly.
en Installation and connection The connection data for the appli- Drinking water connection ance can be found on the rating Connect your appliance to a drinking plate. water connection. Check that the mains plug is inser- ted properly. Installing the drinking water connection Note ¡...
Familiarising yourself with your appliance en Familiarising yourself with your appliance Familiarising yourself with your appliance Familiarising yourself with your appliance Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with "E number and FD number" → Page 63.
en Familiarising yourself with your appliance "Detergent" → Page 31 is added to the detergent Detergent dispenser dispenser. "Bottom basket" → Page 23 Bottom basket Dispenser for special salt Add special salt to the dispenser for special salt. → "Water softening system", Page 27 Lower spray arm The lower spray arm washes the tableware in the bot- tom basket.
Page 17
Familiarising yourself with your appliance en "Switching on the appliance" → Page 35 ON/OFF button and reset button "Switching off the appliance" → Page 37 "Terminating the programme" → Page 37 "Programmes" → Page 19 Programme buttons Info button If you press , the display shows information about selected programmes, basic settings and additional functions.
Page 18
en Familiarising yourself with your appliance buttons You can use these buttons to scroll between the basic settings. → "Changing basic settings", Page 40 Display The display shows information about pro- grammes, basic settings or additional functions. You can change the basic settings via the display and the setting buttons.
Programmes en Programmes Programmes You can find an overview of the pro- runtime will change if the rinse aid Programmes grammes that can be selected here. system is switched off or rinse aid Different programmes, which can be needs to be added. found on the control panel of your The consumption values can be appliance, are available depending...
Page 20
en Programmes Programme: Programme sequence Additional func- tions Tableware: Particularly gentle: SpeedPerfect+ ¡ Cleaning delicate table- ¡ Pre-Rinse Settings in the Intelligent ware, cutlery, temperat- Home Connect ¡ Cleaning 40 °C ure-sensitive plastics, app are adjustable ¡ Intermediate rinse → "Intelligent glasses and stemware. ", ¡...
Additional functions en flashes. Information for test institutes a The programme and the additional Test institutes are provided with in- function are saved. formation for comparability tests, e.g. Tip: To reset the programme, either according to EN60436. use the Home Connect app or reset These are the conditions for conduct- your appliance back to the factory ing the tests, however they are not...
en Features Additional func- Additional func- tion tion gramme and at any ¡ For a better drying res- time when the pro- ult the final rinse tem- ExtraDry gramme is running. perature is increased ¡ Energy and water con- and the drying phase sumption are increased.
Features en Adjusting top basket with side Bottom basket levers Arrange pans and plates in the bot- To wash large items of tableware in tom basket. the baskets, adjust the shelf position of the top basket. Pull out the top basket. To prevent the basket from sud- denly dropping down, hold the side of the basket by the top edge.
en Features Arrange cutlery with the points and sharp edges downwards. You can reorganise the cutlery drawer to make more space for longer/wider items of cutlery. Reorganising cutlery drawer You can fold down the side shelves and front prongs to make more space for longer/wider items of cut- lery.
Features en Folding prongs Extra Clean Zone Use the folding prongs to position Use the Extra Clean Zone in the top tableware securely, e.g. plates. basket to clean soiled tableware thor- oughly, e.g. muesli bowls. You can fold the prongs down to po- sition pans, bowls and glasses Selecting Extra Clean Zone better.
en Before using for the first time Pull the tab on the Extra Clean Place the Extra Clean Zone in the Zone up and forwards . top basket and lock in place . Check that the mounts are in the Set the slider to ON.
Water softening system en Note: If you select Initial start-up To remove any marks from water Home Connect here, make further or other residues, we recommend settings using the Home Connect you operate the appliance without app on your mobile device. tableware before using it for the You can change the settings for first time.
en Water softening system ¡ Special salt for dishwashers can Setting the water softening damage the tub due to corrosion. system To make sure that any special ▶ salt that escapes is washed out Set the water hardness on your appli- of the tub, add the special salt ance.
Water softening system en Switching off the water Regeneration of the water softening system softening system If you find the special salt refill indic- In order to obtain fault-free function of ator irritating, e.g. when using com- the water softening system, the appli- bined detergents with salt replace- ance performs regeneration of the ment substances, you can switch the...
en Rinse aid system Close the lid of the dispenser for Rinse aid system Rinse aid system rinse aid. a The lid clicks into position. Rinse aid system Rinse aid Setting the amount of rinse For optimum drying results, use rinse aid.
Detergent en Press repeatedly until the Detergent Description display shows 0. Liquid detergent Liquid detergent works To save the settings, press faster and is recommen- approx. 3 seconds. ded for shorter "Pro- a The rinse aid system is switched grammes" → Page 19 off and the rinse aid refill indicator without PreRinse.
en Detergent depending on the combination (4in1, ¡ According to manufacturers, com- 5in1, ...), additional components such bined detergents with salt replace- as glass protection or stainless steel ment substances can only be used cleaner. up to a certain water hardness, According to manufacturers, com- usually 26 °E, without adding spe- bined detergents generally only func- cial salt.
Tableware en Add the detergent to the dry deter- Close the lid of the detergent dis- gent dispenser. penser. 50 ml 25 ml 15 ml a The lid clicks into position. If you are using tablets, one is a The detergent dispenser will open enough.
en Tableware Damage to glass and table- Cause Recommendation ware The water temperat- Select a programme ure of the programme with lower temperat- Only put glasses and china in the is too high. ures. dishwasher if it is marked as dish- After the programme washer-safe by the manufacturer.
Basic operation en To save resources, do not pre- Removing tableware rinse tableware under running wa- ter. WARNING Observe the following when arran- Risk of injury! ging tableware: Hot tableware can cause burns to the – Put heavily soiled tableware in skin.
en Basic operation for the combination of energy/wa- "Finish at" (e.g. 15:20 hours). You ter consumption for this type of can change this setting in the "Ba- tableware and evidences conform- sic settings" → Page 38. ity with the EU Ecodesign Direct- To activate timer programming, ive.
Basic operation en Press to resume the pro- gramme. Terminate programme To end a programme early or to switch from a programme that has already started, you will need to can- cel it first. Open the appliance door. Press for approx. 4 seconds.
en Basic settings Basic settings Basic settings You can configure the appliance to meet your needs. Basic settings Overview of basic settings The basic settings depend on the features of your appliance. Basic setting Selection Description Time setting 00:00 - 24:00 Set the current time.
Page 39
Basic settings en Basic setting Selection Description Eco forecast Switch EcoCheck on or off. When selecting the programme, the average wa- ter consumption and energy consumption is briefly shown on the display. Emotion Light Switch the interior lighting of the appliance on or On via main switch off.
en Home Connect Basic setting Selection Description Efficient Dry Activate or deactivate automatic opening of the On in all programmes appliance door during the drying phase. On with Eco 50° If the function has been activated, the running time may increase. → "Efficient Dry", Page 12 Wi-Fi Switch the wireless network connection on or off.
Home Connect en Home Connect services in your coun- Connecting the appliance to WLAN try. You can find information about home network (Wi-Fi) this at: www.home-connect.com. Requirements To be able to use Home Connect, ¡ Home Connect app is installed on you must first set up the connection your mobile device.
en Home Connect Activating Remote Start Data protection When you have selected "Manual" in Please see the information on data the basic settings of this function, ac- protection. tivate the function on your appliance. The first time your appliance is Requirements registered on a home network ¡...
Dishwasher Care and Ma- ance to malfunction. To avoid such chine Cleaner for Dishwashers online faults and reduce odours, we recom- at https://www.bosch-home.com/ mend cleaning your appliance at reg- store or from customer service. ular intervals. Machine Care is a programme which...
en Cleaning and servicing To ensure optimum cleaning perform- Only use machine care products ance, the programme doses the de- specially designed for dishwash- tergents independently of each an- ers. other during the relevant cleaning Pour the machine cleaner into the phase.
Cleaning and servicing en Turn the coarse filter anticlockwise Carefully clean the rim of dirt and remove the filter system . between the coarse and the fine fil- ter. Check that no foreign objects ‒ Re-assemble the filter system. fall into the sump. Make sure that the locking catches on the coarse filter click into posi- tion.
Page 46
en Cleaning and servicing Check the outlet nozzles on the spray arms for blockages under running water and remove any for- eign bodies. Insert the lower spray arm. a The spray arm clicks into position. Insert the upper spray arm and screw it firmly in place.
Troubleshooting en Troubleshooting Troubleshooting You can rectify minor faults on your appliance yourself. Read the troubleshoot- Troubleshooting ing information before contacting after-sales service. This will avoid unneces- sary costs. WARNING Risk of electric shock! Incorrect repairs are dangerous. Repairs to the appliance should only be carried out by trained specialist ▶...
Page 48
en Troubleshooting Fault Cause Troubleshooting Appliance door does not Appliance door brushes Install the appliance correctly as de- ▶ open at the end of the pro- against the appliance or kit- scribed in the installation instruc- gramme. chen cabinets tions and align. Appliance door opens too Door is not correctly adjus- Adjust the appliance door as de-...
Troubleshooting en Fault Cause Troubleshooting Appliance door opens too Door is not correctly adjus- Adjust the appliance door as de- ▶ wide when activated. ted. scribed in the installation instruc- tions. Error code / Fault display / Signal Fault Cause Troubleshooting E:2130 lights up.
Page 50
en Troubleshooting Fault Cause Troubleshooting E:3200 or indicator for wa- Remove the filter from the supply ter supply lights up. hose Clean the filter. Re-insert the filter in the supply hose. Screw the water connection back Check the water connection for leaks.
Troubleshooting en Fault Cause Troubleshooting A different error code ap- A technical fault is present. Press . pears in the display window. Unplug the appliance or switch off the fuse. E:0100 to E:9010 Wait at least 2 minutes. Insert the mains plug of the appli- ance in a socket or switch on the fuse.
Page 52
en Troubleshooting Fault Cause Troubleshooting Tableware is not dry. Use a different combined detergent with a better drying performance. Activate "Extra Dry" → Page 38. Extra Dry not activated to im- ▶ prove drying performance. Tableware removed too Wait until the programme ends. early or drying process not Only remove tableware 30 minutes yet ended.
Page 53
Troubleshooting en Fault Cause Troubleshooting Remnants of food on table- Filters are soiled. Clean the filters. ▶ → "Cleaning filters", Page 44 ware. Filters are inserted incor- Insert the filters properly. → "Filter system", Page 44 rectly and/or not engaged. Engage the filters. Washing programme selec- Select a more intensive washing ▶...
Page 54
en Troubleshooting Fault Cause Troubleshooting Water marks on plastic Due to laws of physics Select a more intensive pro- ▶ parts. droplet formation on plastic gramme. → "Programmes", Page 19 surfaces is unavoidable. After drying water marks are Position tableware at an angle. ▶...
Page 55
Troubleshooting en Fault Cause Troubleshooting Tea residue or lipstick marks Washing temperature is too Select a programme with a higher ▶ on tableware. low. washing temperature. → "Programmes", Page 19 Too little detergent is being Use a suitable "Detergent " ▶ → Page 31 and follow the manufac- used or is unsuitable.
Page 56
en Troubleshooting Fault Cause Troubleshooting Plastic parts are discol- Washing temperature is too Select a programme with a higher ▶ oured. low. washing temperature. → "Programmes", Page 19 Tableware has been pre- Only remove large remnants of food ▶ cleaned too intensely. The and do not prerinse tableware.
Troubleshooting en Fault Cause Troubleshooting Rust spots on cutlery. Cutlery is not sufficiently Use rust-resistant tableware. ▶ rust-resistant. Knife blades are often more severely af- fected. Cutlery may also rust if Do not wash rusting items. ▶ washed together with rust- ing items.
en Troubleshooting Information on display panel Fault Cause Troubleshooting Add "Special salt" → Page 28. Special salt refill indicator Insufficient special salt. ▶ lights up. Sensor does not detect spe- Do not use special salt tablets. ▶ cial salt tablets. Refill indicator for special Water softening system is Setting the water softening system ▶...
Troubleshooting en Fault Cause Troubleshooting → "Terminate programme", Programme starts automat- You did not wait until pro- ▶ ically. gramme ended. Page 37 Appliance stops during the Appliance door is not closed Close the appliance door. ▶ programme or cuts out. properly. Power and/or water supply Check the power supply.
Page 60
en Troubleshooting Fault Cause Troubleshooting Knocking or rattling noise. With a small load the water Distribute the tableware evenly. ▶ jets directly strike against Load the appliance with more table- ▶ the tub. ware. Light items of tableware Position light items of tableware se- ▶...
Transportation, storage and disposal en Insert the pump cover and press Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned.
en Customer Service Protect appliance from frost Disposing of old appliance If there is a risk of frost where the ap- Valuable raw materials can be re- pliance will be standing, e.g. in a holi- used by recycling. day home, empty the appliance com- pletely.
Technical specifications en least 10 years from the date on from water damage, the appliance which your appliance was placed on must be connected to the power the market within the European Eco- supply. nomic Area. ¡ The liability guarantee is valid for the service life of the appliance.
(Please search on the product web- A detailed Declaration of Conformity site for your appliance model and ad- can be found online at www.bosch- ditional documents). Alternatively, home.co.uk among the additional you can request the relevant informa- documents on the product page for tion from ossrequest@bshg.com or...
Page 65
Declaration of Conformity en 2.4 GHz band (2400–2483.5 MHz): Max. 100 mW 5 GHz band (5150–5350 MHz + Only applies to Great Britain 5470–5725 MHz): Max. 100 mW UK (NI) 5 GHz WLAN (Wi-Fi): For indoor use only. 5 GHz WLAN (Wi-Fi): For indoor use only.
Page 68
Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service direct- ory.