• Consult the dealer or an experienced radio/TV technician for help. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to operate this product.
IMPORTANT SAFETY INSTRUCTIONS Read these instructions. 16. Power Cord Caution: Check the TV specifications in the Owner’s Keep these instructions. Manual to determine power requirements. Heed all warnings. Periodically examine the cord of your appliance, and if its Follow all instructions. appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced Do not use this apparatus near water.
Page 4
IMPORTANT SAFETY INSTRUCTIONS 26. Keep the product away from direct sunlight. (Continued from previous page) 27. When mounting a TV on the wall, make sure that none of the 21. Outdoor Antenna Grounding electrical cabling bears any of the weight of the TV. Install in If an outside antenna or cable system is connected to the accordance with the manufacturer’s instructions.
CONTROL/MPI port on the TV rear jack panel. There are three methods for configuring individual TVs that are currently in Pass-through Mode: using one of two LG Setup Wizard options or using the Custom Master TV Setup procedure as described in this document.
Commercial Mode Overview (Cont.) Installer Menu To create a Master TV Setup, you will need to know how to access the commercial controller (PTC) Installer Menu and make changes to xxLY770M PTC INSTALLER MENU the default values as required. If necessary, familiarize yourself with CPU-CTV the Installer Menu and how to make and save changes.
Page 8
Menu settings using one of the following processes: configuration. • Local: Configure an individual LY770M TV’s EBL LG’s FTG File Manager PC software enables you to via its TV-LINK CFG jack using a direct PC-to-TV create an FTG Configuration (.tlx) file, which may be (EBL) connection and the FTG Device Configuration used to configure the CPU for FTG Mode.
Commercial Mode Overview (Cont.) While the TV is in FTG Mode: • Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu items will be read-only. • FTG Mode via CPU configuration changes must be made using a TLX file (typically edited in the FTG File Manager), while FTG Mode via EBL configuration changes must be made using the FTG Device Configuration Application.
Pro:Centric Interactive Menu Navigation LG’s Pro:Centric pillow speaker provides access to both interactive menus and regular TV features. Press PORTAL on the Pro:Centric pillow speaker to access the interactive menus. Note: Interactive menu options may vary, depending on Pro:Centric features enabled for the site. The following are default interactive menus.
TV in Factory Default State When the TV is in a factory default state, LG’s Setup Wizard (see pages 12 to 13) provides automated or manual options for configuring the Pro:Centric server settings. The EZ-Manager branch of the Setup Wizard also provides a USB configuration option that enables you to configure a TV for FTG Mode via CPU using a TLX file stored on a USB memory device.
• If you plan to create a customized Master TV Setup using the procedure described on pages 46 to 48, be sure to exit the LG Setup Wizard in order to avoid setup conflicts or setting modes that may cause the TV to malfunction or restrict the custom setup procedure. See also “Initiate Configuration or Exit the LG Setup Wizard”...
LG Setup Wizard (Cont.) Initiate Configuration or Exit the LG Setup Wizard The Welcome screen provides a brief introduction to the LG Setup Wizard. WELCOME TO LG’S SETUP WIZARD This wizard features two different setup options: . The EXPRESS SCRIPT allows automated setup of hospital features, such as a pillow speaker, and supports physical tuning of clear content channels (no DRM).
Number settings, from this point, the wizard can proceed through each of the configuration steps with no further user interaction. WELCOME TO LG’S EZ-MANAGER WIZARD . Use this setup wizard to configure the TV for Pro:Centric and/or Free-To-Guest (FTG) operation.
EZ-Manager Wizard (Cont.) EZ-Manager Wizard (Cont.) TV Configuration Options From the TV Configuration Options screen, you can choose how to proceed with the configuration of this TV (assuming you do not opt to exit the wizard, which you may also do at any time). Note: If you intend to use the Zoning feature(s) on the TV for location-specific configuration purposes, select the “Zones &...
Page 16
EZ-Manager Wizard (Cont.) Note: Zoning features are only applicable for TVs that will be configured using a TLX file (local or remote configuration). ZONES, LABEL, AND ROOM NUMBER . If creating Wi-Fi Zones for AP settings, select the appropriate Wi-Fi Zone # Wi-Fi Zone (1-99) based on the Wi-Fi Zone in which this TV is installed.
EZ-Manager Wizard (Cont.) Configure Pro:Centric Settings Once you select “NEXT” from the TV Configuration Options screen, the Searching for Pro:Centric Server screen is displayed. Note: Select the “BACK” button, where available, to check previous settings, as necessary. Also note that if any of the configuration steps fails, you will see a “Diagnostics” screen with an indication of the failure.
Page 18
EZ-Manager Wizard (Cont.) If the process is successful, no further user interaction is required, though, in some instances, where the option (for example “NEXT”) is available, you may manually move forward to subsequent steps within the wizard to speed up the process. PROCESSING THE PRO:CENTRIC CONFIGURATION Downloading the Pro:Centric application files takes a few minutes.
Page 19
EZ-Manager Wizard (Cont.) Manual Pro:Centric Configuration 1. With the Searching for Pro:Centric Server screen on display, use the Left/Right arrow keys on the Installer Remote to select MANUAL PRO:CENTRIC at the bottom right of the screen, and then press OK. In the Pro:Centric Manual Configuration screen (see examples below), you will be able to configure the appropriate Pro:Centric settings in the TV.
Page 20
EZ-Manager Wizard (Cont.) (Continued from previous page) 3. Refer to the appropriate subsection below, depending on the Pro:Centric server configuration, to complete the remaining fields. RF Configuration a) In the Media Type field, use the Left/Right arrow keys to select RF. b) In the Data Channel field, use the Left/Right arrow keys to select the RF channel number that will be used by the Pro:Centric server as its data channel.
EZ-Manager Wizard (Cont.) (Continued from previous page) When the Pro:Centric configuration is complete, an EZ-Manager Configuration Complete screen (see example on page 18) is displayed, and after 10 seconds, the wizard exits, and the TV turns OFF. Note: With the EZ-Manager Configuration Complete screen on display, you can also manually turn off or reboot the TV.
Page 22
EZ-Manager Wizard (Cont.) USB Configuration via EZ-Manager Wizard With either the TV Configuration Options or the Zones, Label, and Room Number screen on display, proceed as follows to configure the TV using the USB memory device. 1. Insert the USB memory device with the appropriate file(s) into either of the TV’s USB ports. 2.
Express Script Initiate the Express Script Note: While the Express Script enables you to set up TVs individually in lieu of cloning, you can also use the resulting Express Script TV Setup for cloning purposes (clone programmer only), if desired. However, note that TV setup menu customization via the Express Script is limited to Channels Menu options.
Page 24
Express Script (Cont.) If you wish to proceed with the wizard without changing the default values for the Pro:Centric settings, you can simply select NEXT and press OK on the Installer Remote. Or, if you wish to exit the wizard while retaining the default values for Pro:Centric settings, use the arrow keys on the Installer Remote to select DONE, and then press OK.
Page 25
Express Script (Cont.) (Continued from previous page) 1. In the Pro:Centric Mode field, use the Left/Right arrow keys on the Installer Remote to select the appropriate Pro:Centric Application Mode—FLASH, GEM, HTML, or CONFIGURATION ONLY. Note: For remote management only, select CONFIGURATION ONLY. The TV will search for TV E-Z Installation data downloads;...
Express Script (Cont.) Complete the TV Configuration The following procedure describes the remaining steps in the Express Script. You can select the “BACK” button, where available, to check previous settings, as necessary. Typically, if you do not modify the default settings, the “NEXT” button is automatically selected when you proceed forward within the Express Script.
Page 27
OK. • If applicable, select the pillow speaker code/voltage and press OK. Note: If using a Pro:Centric pillow speaker (LG IR codes) or a pillow speaker with Zenith IR codes, make sure the “Zenith” pillow speaker code (default) is selected.
Page 28
Express Script (Cont.) (Continued from previous page) CHANNEL TUNING Do you want to scan for available channels? RUN AUTO TUNING You MUST select RUN AUTO TUNING and press OK in order to run the channel scan. If you move on to the next step without running Auto Tuning, there will be no analog or digital channels in the channel lineup.
Page 29
Express Script (Cont.) (Continued from previous page) Note: The maximum number of channels (analog, digital, and Aux inputs) that can be transferred to the PTC is 141. An attempt to transfer more than 141 channels of any combination will result in a PTC Channel Map of exactly 141 channels; any extra channels will not be available in the PTC Channel Map.
Page 30
Express Script (Cont.) (Continued from previous page) CHANNEL OVERRIDE Do you want to allow access to channels that are not in the channel lineup? < > BACK EXIT NEXT 7. As the final step of the Express Script, the TV saves your settings and transfers the auto-tuned/ edited channel lineup to the commercial controller (PTC).
Accessing and Using the Ez Download Utility 1. If it is not ON already, turn ON the TV. 2. The next step depends on whether the LG Setup Wizard appears on the screen when you turn ON the TV: • If the wizard is displayed, you can access the Ez Download utility via the EZ-Manager Wizard, as indicated above (see “Before You Begin”).
Page 32
Ez Download Utility (Cont.) (Continued from previous page) 3. If the TV is currently in Pass-through Mode, you would like to transfer (Teach) a TLX file to the TV via the Ez Download utility, and you intend to use one or both of the TV’s Zoning feature(s), assign the appropriate TV Zone # and/or Wi-Fi Zone # in the TV at this time.
Page 33
Ez Download Utility (Cont.) (Continued from previous page) EZ DOWNLOAD TV MANAGER BACK CANCEL Select USB Memory Device Channel Tuning / Channel Banner Display ˇ USB Device 1: Device Name Logical Logo Image ˇ Physical Splash Image 1920 X 1080 ProC.jpg Teach to TV (TLX) ˇ...
Page 34
Ez Download Utility (Cont.) (Continued from previous page) 9. If a TLX file that includes an FTG Channel Map is selected, a Channel Tuning / Channel Banner Display field will be displayed at the right of the screen. If the FTG Channel Map comprises RF channels and Aux inputs only (the latter designated by 130-0 through 137-0), you can choose the format for the channel tuning/banner display.
Accessing the Installer Menu 1. Turn ON the TV. If the LG Setup Wizard appears on the screen when you turn ON the TV, exit the wizard. 2. Using an Installer Remote, press MENU repeatedly until the on-screen display of the TV setup menus (if the TV is in Pass-through Mode) or the Function Menu (if the TV is not in Pass-through Mode) no longer toggles, and then press the Installer Menu entry sequence (e.g., 9-8-7-6) + OK...
Installer Menu (Cont.) As part of the Installer Menu header (in all modes), two 3-character acronyms are displayed to indicate the TV’s current configuration mode. The table below lists all possible mode identifiers for these TV models. Acronym Description CPU-CTV Pass-through Mode with Channel Lineup in CPU CPU-FTG FTG Mode via CPU...
Installer Menu (Cont.) Installer Menu Items 000 through 049 Item Function Value Range Default Value Brief Description of Function INSTALLER SEQ 0 ~ 3 Leave default set to 0. Selects the number of hours of inactivity allowed before the TV automatically POWER MANAGE 0 ~ 7 turns itself OFF.
Page 38
Installer Menu (Cont.) Installer Menu Items 053 through 122 Item Function Value Range Default Value Brief Description of Function DIS. CH-TIME 0 / 1 Set to 1 to disable Channel-Time display. EN. CH-T COL. 0 / 1 Set to 1 to enable custom color for the Channel-Time display. FOR.
Page 39
Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE 003 - BAND/AFC (Band/Automatic Frequency Control) Specifies entry sequence to the Installer Menu. There are four possible settings for this option: 0 = 9876 1 = 4321 0 = Broadcast 1 = CATV (default) 2 = 1478...
Zenith (Hospital) 1 – 2 Pillow Only 027 HOSPITAL MODE is set to 0. Note: See Reference section, “LG Pro:Centric Patient Remote and Pillow Speaker,” for additional information. Also, see documentation for the accessory package that includes the multi- code remote.
Installer Menu (Cont.) 021 - V-CHIP (Parental Control) Pillow Speaker Value Speaker Hospital IR Code Set to 1 to activate V-Chip (Parental Control) and have it available Code/Voltage to the end user to filter and control or otherwise restrict program- Zenith (+12v) Determined by Determined by item...
Page 42
Disabled LG Sound Sync (optical) 039 - REAR AUX EN. (Rear Aux Enable) Enabled LG Sound Sync (BT wireless) Set to 1 to enable display panel rear Aux (AV) input. Set to 0 to Disabled LG Sound Sync (BT wireless) disable display panel rear Aux (AV) input.
Page 43
Installer Menu (Cont.) 073 - CH NOT AVBLE (Channel Not Available) 084 - PERMANENT BLK (Permanent Block) If set to 1 and item 028 CH. OVERIDE is set to 0, a “CHANNEL Allows Lock (Parental Control) blocking schemes to be permanent NOT AVAILABLE”...
Page 44
If set to 0 (default), the TV’s MMR (Magic Motion Remote) feature Caution: POWER SAVINGS should NEVER be set to 7. is enabled, and a compatible LG MMR (not supplied) may be used This setting is intended for factory use only.
Page 45
TV is turned OFF. Type is set to “IP” in the EZ-Manager Wizard or Express Script or in the IP Environment / Pro:Centric Menu on the TV (see “LG Note: This item is not available in the Installer Menu when item Setup Wizard”...
Custom Master TV Setup This section describes how to create a customized Master TV Setup for cloning purposes when the TV is in Pass-through Mode. All cloning (Learning and Teaching) processes on the TV are performed via USB memory device / TLX file. The Master TV Setup may be Learned to a TLX file, which can then be used to Teach configuration either to TVs that are to remain in Pass-through Mode or to TVs that are to be configured for FTG Mode via CPU.
Custom Master TV Setup Procedure 1. Turn ON the TV. The next step depends on whether the LG Setup Wizard appears on the screen when you turn ON the TV: • If the wizard is displayed, the TV is in the required factory default state.
Page 48
Custom Master TV Setup (Cont.) (Continued from previous page) 4. Set up TV features. On-screen setup menus control the features of the TV. Press MENU QUICK SETTINGS on the Installer Remote to access the TV setup menus, and then set Channel, Picture, Sound, etc.
Channel Banks Setup Channel Banks Overview Channel Banks enable institution administrators to create tiered channel programming on patient in-room TVs. Each channel bank may offer a custom channel lineup for a pre-determined fee. LY770M TVs are configured with four channel banks, i.e., Channel Banks 1, 2, 3, and 4. The top tier generally contains the most programming (premium, etc.), 2nd tier = lesser programming, 3rd tier = basic programming, etc.
Channel Banks Setup (Cont.) Inactive TV Setup To create an inactive TV display on Channel Bank 4: 1. Press CH. BANK on the Installer Remote until Channel Bank 4 is selected, and then press CH. PREVIEW to display the Channel Preview/Banks Setup Menu. 2.
Channel Banks Worksheet Use this worksheet to plan your program packages. (Photocopy additional worksheets as needed.) Channel Number Channel Number Channel Number Channel Number Channel Number Date _____________ Installer _____________________________________ Page ___ of ____ Location ______________________________________________________________________ 206-4271...
Cloning Procedures Cloning typically refers to the process of capturing a Master TV Setup and transferring it to a Target TV. This section describes how to save (Learn) a Master TV Setup and transfer (Teach) it to a Target TV using a USB memory device / TLX file. You can also create a TLX file using the FTG File Manager and then use the Teaching procedure to transfer the TLX file to Target TVs.
Page 54
Cloning Procedures (Cont.) (Continued from previous page) 6. Use the Up/Down arrow keys to select Learn From TV (TLX), and then press OK. TV MANAGER CANCEL USB Download Menu Ez Download Diagnostics Menu Logo Image Download Update TV Software Update PTC Software Teach To TV (TLX) Learn From TV (TLX) 7.
Cloning Procedures (Cont.) (Continued from previous page) 8. When you are ready to initiate Learning, use the arrow keys to select OK on the screen, and then press OK on the Installer Remote. Learning status will be shown in a pop-up progress banner at the bottom of the Learn From TV (TLX) screen.
Page 56
Teach Configuration to Target TV 1. Turn ON the Target TV. 2. The next step depends on whether the LG Setup Wizard appears on the screen when you turn ON the TV: • If the wizard is displayed, you can complete the Teaching process via the EZ-Manager Wizard, as indicated above (see “Before You Begin”).
Page 57
Cloning Procedures (Cont.) (Continued from previous page) 3. If applicable (see also “Before You Begin” above), make sure to assign the appropriate Zone designation(s) in the Target TV at this time. Note: In order for the proper location-specific TV Zone and/or Wi-Fi Zone profile data to be applied, the Zone designation(s) must be assigned in the Target TV(s) BEFORE Teaching is performed.
Page 58
Cloning Procedures (Cont.) (Continued from previous page) • If the TLX file includes an FTG Channel Map with RF channels and Aux inputs only, you can choose the format for the channel tuning/banner display. Use the arrows keys to select the desired Channel Tuning / Channel Banner Display option—either Logical or Physical—at the right side of the Teach to TV (TLX) screen.
IN FTG MODE, THE CPU CANNOT BE SWITCHED TO FTG MODE. This section provides an overview of the FTG File Manager, which is used for FTG Mode via CPU configuration. The software is available online at: www.lg.com/us/commercial/display-solutions/ftg. Creating an FTG Configuration File The procedure below describes how to use the FTG File Manager utilities (see sample screens on pages 61 to 64) to create an FTG Configuration (.tlx) file that can be saved to a USB memory device.
Page 60
FTG File Manager Utilities Overview (Cont.) (Continued from previous page) Note: To remove an individual item from the FTG Configuration List or the TV Setup Menu List, click on/ highlight the item to be removed, and then click the Remove Item button directly above the applicable “List”...
FTG File Manager Utilities Overview FTG File Manager Main Screen The FTG File Manager main screen enables you to compile, modify, and save FTG Configuration (.tlx) files. It also allows you to change the Zone assignment for each Installer Menu profile, if desired (see Reference section, “Using the TV’s Zoning Features,”...
FTG File Manager Utilities Overview (Cont.) FTG Channel Map Configuration Utility The FTG Channel Map Configuration Utility enables you to create, view, edit, and print a Logical Channel Map. EDIT/ADD MAP PRINT MAP Click to open the FTG Click to display a printable Channel Map Editor to create FTG Channel Map Report.
FTG File Manager Utilities Overview (Cont.) FTG Channel Map Editor The FTG Channel Map Editor shows a single Logical Channel’s data and the FTG Channel Map. LOGICAL CHANNEL MAPPING CUSTOM CHANNEL LABELS/ICONS SET CHANNEL ATTRIBUTES Select a Logical Channel number. Then, Enter custom labels and select icons Check/select Encrypted, OSD, assign the RF, Major, and Minor channel...
FTG File Manager Utilities Overview (Cont.) FTG Installer Menu Configuration Utility CONFIGURATION SETTINGS Select tabs for categories of Installer Menu items to set up TV. Filename of opened FTG Configuration (.rml) file created using FTG Device Configuration Application. Note: The Pro:Centric tab enables you to set up Pro:Centric-specific parameters. The LAN tab enables you to set up a variety of LAN features, including the Wi-Fi Zoning feature.
IP Environment Setup The IP Environment Menu enables you to set up the network features of the TV. If you intend to create a Master TV Setup for cloning purposes (see Master TV Setup procedure on pages 46 to 48), all IP Environment settings, with the exception of Wired Network Connection settings and the TV name (editable in the Media Share Menu), may be cloned.
Page 66
IP Environment Setup (Cont.) (Continued from previous page) RF Configuration a) Select/highlight the Media Type field and press OK on the Installer Remote to display the drop-down list of options. Then, use the Up/Down arrow keys to select RF. Note: If the Media Type has already been set in the EZ-Manager Wizard, the specified value will be reflected in this field.
IP Environment Setup (Cont.) (Continued from previous page) Pro:Centric Application Mode Configuration Select/highlight the Mode field and and press OK on the Installer Remote to display the drop-down list of options. Then, use the Up/Down arrow keys to select the appropriate Pro:Centric Application Mode setting—Configuration Only, FLASH, GEM, or HTML.
Page 68
IP Environment Setup (Cont.) Configuring a Wired Network Connection Note: If desired, you can configure both wired and wireless connections. However, note that a wired connection is always NETWORK prioritized over a wireless connection. That is, when the TV is Pro:Centric turned OFF and then back ON, if a LAN cable is detected between the TV and the network, the TV will default to the wired connection.
Page 69
IP Environment Setup (Cont.) (Continued from previous page) If the network is connected successfully, a “Connected to Internet” message will appear just below the progress display. If the network connection is not successful, the progress display will identify the network element in which the connection failed. Check your cabling and/or verify the configuration data, as necessary.
Page 70
IP Environment Setup (Cont.) IP Stream Control If necessary, due to an audio and/or video stream delay, IP Stream Control options enable you to compensate for synchronization irregularities by allowing audio PTS and video PTS offset modifications. This menu also enables you to specify the IGMP version (2 or 3). Note that any modifications to these settings should be performed by qualified personnel only.
Page 71
Allows guests to use the TV to access and view Pro:Centric ® data shared either by wired DLNA Certified devices connected to the same LAN as the TV or by wireless LG devices using LG’s Network ® Smart Share application with Wi-Fi Direct Smart Share...
IP Environment Setup (Cont.) Pre-loaded Applications This option allows you to select which of the pre-loaded application icons to display in the TV’s Smart Launcher, which appears along the bottom of the screen. When the Pro:Centric application is disabled, the Smart Launcher is available to end users via the PORTAL button on the remote control.
Page 73
Reference: Updating TV/PTC Software using a USB Memory Device This section describes how to update TV (CPU) and/or PTC software using the TV Manager / USB Download Menu “Update TV Software” and/or “Update PTC Software” option(s), respectively, though you may also use the Ez Download utility to update software, if desired. See “Ez Download Utility”...
Page 74
Reference: Updating TV/PTC Software using a USB Memory Device (Cont.) (Continued from previous page) 5. In the next screen (Update TV Software or Update PTC Software depending on your selection in step 4): • If more than one USB memory device is currently connected to the TV, be sure to select the USB device that contains the software file you wish to use.
Reference: Downloading a Splash Screen Image using a USB Memory Device This section describes how to download a splash screen image using the TV Manager / USB Download Menu “Logo Image Download” option, though you may also use the Ez Download utility to download the splash image, if desired.
Page 76
Reference: Downloading a Splash Screen Image using a USB Memory Device (Cont.) (Continued from previous page) 5. In the Logo Image Download screen: • If more than one USB memory device is currently connected to the TV, be sure to select the USB device that contains the image file you wish to use.
Reference: Power Consumption Settings The following tables assume that Installer Menu item 118 POWER SAVINGS is set to 3 (default) and Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 255). 32LY770M 42LY770M Item 099...
Reference: TV Aux Input Configuration ENABLE MPI DATA MPI DATA DATA STATUS DATA STATUS DIRECT ACCESS Installer STATUS TYPE TYPE 0xD2 TYPE 0x0D Tuning Menu Item Installer Menu 0x41 SOURCES CURRENT AV 046 START ENABLED (R/W) SOURCE (R) SOURCE (R) AUX SRCE (Start Aux Installer...
3 (default) A b-LAN enabled head end device, such as an LG FMA-LG101, broadcasts over the RF distribution system to communicate to multiple TVs. When the TV is first installed, it must be turned ON in order for its embedded b-LAN module to receive communication from the head end device.
(EBL) connection. Refer to the Free-To-Guest (FTG) Device Configuration Application User Guide for further information. FTG Device Configuration Application software is available online at: www.lg.com/us/commercial/display-solutions/ftg. Note: If the TV CPU is already in FTG Mode, you cannot use this procedure to make changes to the FTG Channel Map and FTG Installer Menu settings.
Reference: Auto Input(s) Sensing Feature This section provides detailed settings information for Installer Menu item 042 AUTO INPUTS. Note: When both item 042 AUTO INPUTS and item 041 SIMPLINK EN are enabled in the Installer Menu, HDMI inputs will be detected by SIMPLINK, but the Auto Input(s) Sensing Feature will not function. In the Installer Menu, an informational code is displayed at the right of each Auto Inputs value, for example: xxLY770M PTC INSTALLER MENU CPU-CTV...
The following table identifies when and how the LY770M hospital features are supported in three different TV configurations. As indicated in the introduction to this document, LG commercial TV functionality is based on “ownership” of the Channel Map. For the purposes of this table, “CPU” indicates that the TV is in Pass- through Mode with the Channel Map in the CPU (i.e., auto-tuned/edited channel lineup) and “PTC”...
Reference: LY770M Hospital Operations (Cont.) Speaker Selection The following table outlines speaker settings as determined by Installer Menu items 027 HOSPITAL MODE and 020 FEATURE LEVEL. Item 027 HOSPITAL Item 020 FEATURE Sound Out Menu Speaker MODE Value LEVEL Value TV Speaker None TV Only...
This section describes how to restore a single TV, regardless of its mode, to a factory default condition. The following procedure requires that you contact LG technical support to obtain a predefined value/ password for Installer Menu item 117 FACT DEFAULT that enables access to initiate a factory “IN-STOP”...
Reference: Using the TV’s Zoning Features This section describes the TV Zoning and Wi-Fi Zoning features available with the LY770M model TVs. These features are primarily intended for use when the TV is configured for FTG Mode via CPU operation; however, Wi-Fi Zoning, along with selected elements of TV Zoning (Installer Menu and TV Setup Menu profile Zone assignments), may also be used with TV cloning processes using a USB memory device / TLX file.
Page 86
Reference: Using the TV’s Zoning Features (Cont.) Note: While a channel can be restricted from up to eight Zones, a TV can only ever be in (set for) one Zone. See also the FTG Channel Map Editor overview on page 63. At the same time, keep in mind that the TV Zone designations are not mutually exclusive.
Page 87
Reference: Using the TV’s Zoning Features (Cont.) Using the Wi-Fi Zoning Feature with Cloning Configuration A location-specific Wi-Fi configuration / TLX file may be saved (Learned) from an individual TV as part of a Master TV Setup and then be used during Teaching. First, the wireless network (i.e., the access point login data) must be configured in the Master TV’s IP Environment Menu (see “Configuring a Wi-Fi Network Connection”...
Page 88
Reference: Using the TV’s Zoning Features (Cont.) (Continued from previous page) • Label: Allows you to select a North, South, East, or West text label for this TV. Select/highlight the Label field and press OK. Then, use the Up/Down arrow keys to select the applicable label. Press OK when you are finished.
Certified devices on the same LAN as the TV or using wireless LG devices/Wi-Fi Direct. If you intend to connect to an LG device using Wi-Fi Direct, remember that you must also turn ON Wi-Fi Direct and launch the Smart Share application on the LG device.
Page 90
WI-FI DIRECT Quick Quick REFRESH LIST Picture Picture Note: The example at left Language [TV]LG Smart TV shows the General Menu when Room Info the TV is in Pass-through Mode. Time & Date Sound Sound The Wi-Fi Direct screen is the...
Page 91
Reference: Using Media Share Features (Cont.) Bluetooth Sound Sync Note: Bluetooth Sound Sync is only accessible from the TV’s Smart Launcher. If the TV is not in Pass-through Mode, you will need a remote with a SMART button in order to display the Smart Launcher. The following steps describe how to access and use the Bluetooth Sound Sync feature.
Reference: LY770M Rear and Side Jack Panels Use for video IP and/or network connections. OPTICAL DIGITAL AUDIO OUT Use for amps and home theater systems. SPEAKER OUT / LINE OUT Note: When the TV is OFF, this port is not (3.5 mm jack) Connect external audio (fixed enabled.
Reference: External Stereo Speaker Specifications The SPEAKER OUT / LINE OUT 3.5 mm stereo jack on the LY770M rear panel provides stereo speaker signal outputs (fixed speaker, variable speaker, or fixed line level [amplifier]) for external audio equipment. Set Installer Menu item 097 AUDIO OUTPUT as required in accordance with external audio equipment connected to the TV.
Reference: Installer Remote Control Typical Key Functions An LG Installer Remote is required to set up and operate the TV. The LG Installer Remote illustrated below shows typical remote control functions and is provided for reference only. TV LG1/TV LG2 & TV Z1/TV Z2...
IR codes based on “bed number” in a multi-TV CH - VOL - single room installation. The remote may be set from Bed 1 to Bed 4. Note: The TV will always respond to the standard LG Installer Remote PORTAL INFO GUIDE IR code scheme, i.e., you can always use an Installer Remote with the...
Page 96
Reference: LG Pro:Centric Patient Remote and Pillow Speaker (Cont.) USB Media Navigation This section provides a brief overview of the LG Pro:Centric patient remote and LG Pro:Centric pillow speaker navigation tools for use with USB media files (photos, videos, music, etc.).
Controlling the TV with Serial Data These TV models are capable of being controlled by a single-wire, serial PREV MUTE data signal. This is an LG patented technology and is being implemented SLEEP OPTION by certain brands of “smart” pillow speakers.
Reference: VESA Standard TV Mounts General Guidelines: Choosing a Location for Installing a VESA Standard Mount To the right are some examples of VESA standard mounts. Since there are numerous types of stands and mounts available, only a few are shown here. Refer to the instruc- tions provided with the TV stand that will be used to mount the TV.
Too much light in room. Dim room light. Remote IR codes do not match Make sure the Installer Remote is compatible. Contact your LG setting(s) in TV. representative, as necessary. Then, check settings both in the TV and on the remote. IR codes sent by the remote must match the setting(s) in the TV.
Troubleshooting (Cont.) Commercial Mode Check / FTG Operation Troubleshooting Commercial Mode Check Use this flowchart to determine whether the TV is currently in Commercial Mode. Press POWER on Installer Remote. connected Plug into AC TV turned to AC Power outlet. Power? Leave the TV set ON, and press MENU on...
Troubleshooting (Cont.) Channel Banks Setup Troubleshooting CHANNEL PREVIEW - BANK 1 CH 011-001 NORMAL-ADDED Enter -> Change CC -> VCHIP Menu, Ch. Preview -> Exit Channel Preview/Banks Setup Menu Possible Cause Possible Solution Symptom Cannot change channel Channel Access was denied in Express Set CH.
HDTV TV’s tuner or Aux inputs. Refers to a particular commercial mode of and other high-value digital content. operation within an LG TV. See also FTG Mode. Embedded b-LAN module. See also b-LAN. Protocol Translation Controller. The...
In addition to the source code, all referenced license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon e-mail request to opensource@ lge.com.
Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric, Smart Share, and the “LG” logo are registered trademarks of LG Electronics Inc. b-LAN is a trademark of SONIFI Solutions, Inc. DLNA Certified is a registered trademark of Digital Living Network Alliance. Intel is a registered trademark of Intel Corporation in the U.S.