Page 1
Digital 4K Video Camera Recorder FDR-AX40 FDR-AX53 FDR-AX55 FDR-AXP55 SERVICE MANUAL 1st Edition (Revised 1)
Page 2
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 3
Be sure to keep your PC used for service and checking of this 修理時に使用するパソコンは,ウィルス検出ソフトが常にアッ プデートを行っているパソコンを使用してください。もし,修 unit always updated with the latest version of your anti-virus software. In case a virus affected unit was found during service, 理を行うセット,もしくはパソコンがウィルスに感染している 事が判明した場合は,ソニーグループ内は社内技術相談窓口に, contact your Service Headquarters. 特約店様は特約店様専用電話窓口(修理窓口)にご相談くださ い。 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 4
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
Help Guide is an on-line manual. Refer to it for in-depth instructions on the many functions of the camcorder. • Adjust Manual (Available on request) The adjustment software is necessary for adjustment and various checking of this unit for the service. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Access error (External media) Turn power off and turn power on again. Abnormality of the drive (External Turn power off and turn power on again. media) Continued Function of this code is not provided in this unit. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 18
Check whether this error is due to the lens or the board. Replace the faulty lens or board. Continued Start the Adjust Manual in the Adjust Station and execute the “Destination data write” on the ADJUST tab. Function of this code is not provided in this unit. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 19
When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items. After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation. Function of this code is not provided in this unit. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 20
Turn power off and turn power on again. When this error is not cleared, the peripheral circuit of the projector may be faulty. Replace the board that contains this peripheral circuit. Function of this code is not provided in this unit. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Identify the cause of the problem (lens or VC-1042 board), and replace the faulty lens or the VC-1042 board. 1-2-4. E:62:20 Abnormality of Thermistor Check the connection between the lens block and VC-1042 board. Identify the cause of the problem (lens or VC-1042 board), and replace the faulty lens or the VC-1042 board. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
• The proper way to disconnect a connector is to grab the connector instead of the wires. If you pull on the wires, they might be broken. • The proper way to connect a connector is to grab the connector instead of the wires. If you push on the wires, they might be broken. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Start the Adjust Manual in the Adjust Station and execute the “Projector Data Reference” on the DATA tab. 2-3-5. Update of MAC Address When a board that contains Wi-Fi has been replaced or when replacing a board that contains the main IC (CPU), the IC’s unique number (MAC address) must be reloaded. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Unless these script files are executed, the following symptoms may appear. Make sure execute the above script files. • The internal memory is not recognized as a media. • The management file saved in the internal memory cannot be repaired. • The internal memory cannot be formatted. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 27
(several seconds later) "SetOverallReadMINI OK" is displayed. Disconnect the USB cable, and turn off the power switch. During the power is turning-on, pull-out the AC-adaptor. Then connect the AC-adaptor Again. The process is executed automatically. (It's running with blue color monitor.) FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
In case the shim was lost or mounting location of the shim was lost, replace the LSV-1820A Lens Device (Service). The case of work to change a lens Check the shims data seal attached to LSV-1820A Lens Device (Service). Memorize the shims information (six digits alphabet). Shims data seal Shims information (six digits alphabet) XXXXXX Fig. 2-4-1 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 29
Prepare for necessary the shims from converted shims information (P1 to P3), and attach them as shown in Fig. 2-4-2. Note Tightening order of screws: P2, P3, P1 Refer to “Notes on Assembling the Lens Section-3” when installing the CMOS Assy. Fig. 2-4-2 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
At this point, be careful not to slide the unit. Example of the shot image Fig. 2-4-4 Checking method Set the unit as the following and focus. Focus: Manual Shoot with self-timer. Make sure that the shot image is obtained the criteria shown in Fig. 2-4-5. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 31
• Display the shot image using arbitrary viewer (Windows photo viewer etc.) at the same magnification. Check the image solution. * Check the five patterns in center and four corners at the same magnification. Near the limit NG or out of focus Fig. 2-4-5 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Turn on the power of the unit and enable the Wi-Fi function. (Upon completion of the preparation for Wi-Fi connection, the password for Wi-Fi connection is displayed.) Confirm on the PC or the smartphone that the unit is detected as a connectable wireless network. 2-10 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj” on the ADJUST tab. Note The sensitivity of the angular velocity sensor is indicated only on the repairing board, but is not indicated on mass production boards. 2-11 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Replace both projector unit (light emitting block) and PJ board. (*1) Projector Data Input Fixed value input Enter the number on the label attached to the unit. Serial number input LD40Syywwnnnnn Enter the red part. Inspect projector LED. ( 1) 2-12 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 35
Replace both projector unit (light emitting block) and PJ board. (*1) Projector Data Input Fixed value input Enter the number on the label attached to the unit. Serial number input LD40Syywwnnnnn Enter the red part. Inspect projector LED. ( 1) Measure brightness. ( 2) 2-13 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
It is the software to adjust and check digital cameras and camcorders for service. The installer of the Adjust Manual and the installation manual are attached, be sure to confirm the contents of them. Note Be sure to install Adjust Station first. FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
ID の書き込み方法: Adjust Station から Adjust Manual を起動し, ADJUST タブにある“PRODUCT ID & USB SERIAL No. INPUT”を実施してください。 2-3-4. リストアデータ (Projector Model) 補修用基板に交換する場合は,必ず事前に交換前の基板から下記のデータを抽出してください。 • Fixed value(プロジェクターの照射性能を示す値) • Serial number (プロジェクターユニットの製造シリアル番号) データの抽出方法: Adjust Station から Adjust Manual を起動し, DATA タブにある“Projector Data Reference”を実施して ください。 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 60
View Position Top View Left View Back View Right View Front View Bottom View The shape may be different from the illustration depending on models. 機種によって形状がイラストと異なる場合があります。 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
The shape may be different from the illustration depending on models. 機種によって形状がイラストと異なる場合があります。 4-2-1. Overall Section-1 • Refer to “Overall Section-1” on exploded view for Ref. No. Except AX40 AX40 (Claws) (Claws) (Claw) (Claw) (Hook) AXP55 Except AXP55 Overall Section-2 Except AX40 AX40 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 62
[1] Remove the Grip Belt {1}-1 from the Belt Sheet Metal {1}-2 → #2 X 1 → #2 X 2 Left View Bottom View {1}-1 {1}-2 [2] open the LCD {2}-1 → #2 X 1 → #2 X 1 → Remove in numerical order in the figure. Bottom View Back View {2}-1 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 63
[4] open the Lid {4}-1 → #12 X 1 → #12 X 1 → #2 X 3 → Open the Cover {4}-2 → #2 X 2 → Pull out the EVF {4}-3 Left View Bottom View {4}-1 Right View Top View {4}-2 {4}-3 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Overall Section-2 • Refer to “Overall Section-2” on exploded view for Ref. No. Be careful not to break the PHOTO Button. (Claw) Except AX40 EVF Section (Hook) Front Cabinet Section AX40 (Claws) (Hook) Except AX40 ANT901 Overall Section-3 Except AX53 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 65
[2] #2 X 1 → #2 X 1 → Tilt up the EVF {2}-1 → #2 X 1 Bottom View Left View {2}-1 Back View [4] #3 X 1 → #2 X 1, #3 X 1 Bottom View Left View FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 66
[5] #3 X 1 Top View [6] #3 X 2 Top View [7] #11 X 2 Top View FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 67
Notes on Assembling the Overall Section-2 Routing the Cable NFC Antenna Hooks Hooks Cable Inner Mold (488) Guide FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
(Note 1) #124 #124 Lens Section-1 Overall Section-4 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions. 電池の交換は, 正しく行わないと破裂する恐れがあります。 電池を交換する場合には必ず同じ型名の電池又は同等品と交 換してください。 使用済み電池は, 取扱指示に従って処分してください。 4-10 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 69
Heat Sink may be adhered by adhesive force of the Radiation Sheet. 放熱シートの粘着力により, 放熱板が固着している場合があり ます。 Disassembly Places [1] #3 X 2 → #3 X 1 → #2 X 2 Right View Left View Top View [2] #2 X 3 Right View 4-11 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 70
[3] #3 X 3 Top View [4] #3 X 4 Back View 4-12 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 71
When installing the MS-1031 Board, shifting it in the direction of the red arrow and attach it. Note: - Be careful not to press the LED portion (red circle portion of figure) with fingers. - When shifting and attaching it, be careful not to deform the VC Heat Sink (R(488)). 4-13 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
4-2-4. Overall Section-4 • Refer to “Overall Section-4” on exploded view for Ref. No. AX40 Except AX40 (Claw) Except AX40 (Claw) Cabinet (R) Block Section 4-14 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 73
Disassembly Places [1] #3 X 1 → #12 X 1 Left View Right View [3] #11 X 1, #2 X 1 Front View [4] #3 X 1 Top View [5] #2 X 1 Back View 4-15 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 74
Routing the DC Jack Guides Guides DC Jack Installing the AJ-1001 Board When installing the AJ-1001 Board, shifting it in the direction of the red arrow and rotating it in the direction of the blue arrow, then attach it. 4-16 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 75
Installing the Cabinet (R) Block When installing the Cabinet (R) Block, tighten the screw while pressing the red circle portion. Screw 4-17 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 76
Ref. No. SP901 #271 LCD Section #288 (Note 1) #288 (Note 1) Note 1 This screw cannot be reused. Discard the screw removed once in servicing. Instead, use a new screw. このねじは再利用することができません。 サービス対応時に一度でも外した場合は新品のねじと交換 してください。 4-18 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 77
Notes on Assembling the Cabinet (R) Block Section Routing the Speaker Cable Guides Speaker Guides 4-19 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
“Front Cabinet Section” on exploded view for Ref. No. Except AX40 AX40 #288 (Note 1) #288 (Note 1) Note 1 This screw cannot be reused. Discard the screw removed once in servicing. Instead, use a new screw. このねじは再利用することができません。 サービス対応時に一度でも外した場合は新品のねじと交換 してください。 4-20 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 79
Notes on Assembling the Front Cabinet Section Installing the Ornament Cabinet (488) When installing the Ornament Cabinet (488), shifting it in the direction of the arrow and tighten the screw in the order of (1). Shifting direction 4-21 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Note 1 This screw cannot be reused. Discard the screw removed once in servicing. Instead, use a new screw. このねじは再利用することができません。 サービス対応時に一度でも外した場合は新品のねじと交換 してください。 Note 2 Use this to cut or splice so that it becomes the designated size. 指定のサイズになるように形状を加工して使用してください。 4-23 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 82
Roll the FP-2359 Flexible Board 2 times in the T Type Hinge (M (P)) Assy Install the Hinge Cover (C (4884)). as shown in the figure below. T Type Hinge (M (P)) Assy FP-2359 Flexible Board 2 times Hinge Cover (C (4884)) 4-24 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 83
Attaching the Magnet Install the magnet with the marking oriented as shown in the figure below. Marking (The color of the marking is red or black.) 4-25 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Note 1 This screw cannot be reused. Discard the screw removed once in servicing. Instead, use a new screw. このねじは再利用することができません。 サービス対応時に一度でも外した場合は新品のねじと交換 してください。 Note 2 Use this to cut or splice so that it becomes the designated size. 指定のサイズになるように形状を加工して使用してください。 4-26 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 85
Roll the FP-2359 Flexible Board 2 times in the T Type Hinge (M (A)) Assy Install the Hinge Cover (C (488)). as shown in the figure below. T Type Hinge (M (A)) Assy FP-2359 Flexible Board 2 times Hinge Cover (C (488)) 4-27 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 86
Attaching the Magnet Install the magnet with the marking oriented as shown in the figure below. Marking (The color of the marking is red or black.) 4-28 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
(Note 1) (Note 2) (Note 2) (Size: 12 x 4 mm) (Size: 8 x 12 mm) Note 1 This screw cannot be reused. Discard the screw removed once in servicing. Instead, use a new screw. このねじは再利用することができません。 サービス対応時に一度でも外した場合は新品のねじと交換 してください。 4-29 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 88
Use this to cut or splice so that it becomes the designated size. 指定のサイズになるように形状を加工して使用してください。 Note 3 Machining for preventing screws from loosening is applied to this screw. If this screw is turned a few times or more, do not reuse it and use a new one. このねじは緩み防止加工が施されています。 2 〜 3回以上外した場合は, 再利用せず新品のねじを使用して ください。 4-30 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 90
If this screw is turned a few times or more, do not reuse it and use a new one. このねじは緩み防止加工が施されています。 2 〜 3回以上外した場合は, 再利用せず新品のねじを使用して ください。 Note 4 Do not reuse the Lens Radiation Sheet (488) because it is adhesive force decreases when it is removed once. Lens Radiation Sheet (488) は一度剥がすと粘着力が弱くなる ため, 再利用はしないでください。 4-32 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
4-2-12. Lens Section-3 • Refer to “Lens Section-3” on exploded view for Ref. No. (including CMOS imager and CM-1017 board) #118 #309 #309 4-33 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 92
Position the upper side boss (1 pcs) while the lower portion of CMOS Block Assy is lifted a little. Note: Do not position the two lower-side bosses first. Upper side boss (1 pcs) Install the Spacer Plate and position the two lower side bosses. Tighten the screws in the order of P2, P3 and P1. 4-34 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Carry out replacement work with this Lens Cap attached. Lens Cap 4-3-1. Removal of Lens Device Remove the retaining ring E-2.5. Retaining Ring E-2.5 Remove the screw to detach the Front Ornament (1820). TP1.4 x 4 Front Ornament (1820) Claws Hook Remove the screw. 4-35 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 94
Main Flexible Assy (0030) Motor A Flexible Board M1.7 x 2.5 Motor B Flexible Board Remove the screw. M1.7 x 2.5 Main Flexible Assy (0030) Peel off the adhesive part of LF-2130 Flexible Board. LF-2130 Flexible Board Adhesive part 4-36 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 95
Peel off the adhesive parts of Motor A Flexible Board and Motor B Flexible Board. Adhesive part Motor B Flexible Board Adhesive part Motor A Flexible Board Remove the seven screws to detach the Sheet Metal (C (0030A)). Sheet Metal (C (0030A)) M2 x 3 M1.7 x 2.5 M1.7 x 2.5 4-37 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 96
M2 x 3 M2 x 3 10. Disconnect the LF-2130 Flexible Board from the connector on the CM-1017 board and peel off the adhesive part of LF-2130 Flexible Board while avoiding a rib. LF-2130 Flexible Board Adhesive part CM-1017 Board 4-38 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 97
12. Peel off the adhesive part of Motor A Flexible Board. Adhesive part Motor A Flexible Board 13. Remove the three screws to detach the Motor B Block Assy. Motor B Block Assy M1.7 x 2.5 M1.7 x 2.5 4-39 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 98
16. Remove the three screws to detach the Motor A. 17. Remove the Sheet Metal (A (0030A)). Sheet Metal (A (0030A)) TP1.7 x 5 Motor A Motor A TP1.7 x 5 18. Disconnect the LF-2126 Flexible Board from the connector on the Main Flexible Assy (0030). 4-40 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 99
Flexible Board Adhesive part 20. Remove the four screws to detach the Sheet Metal (D-Sub-A (0030A)). TP1.7 x 5 Sheet Metal TP1.7 x 5 (D-Sub-A (0030A)) 21. Peel off the Polyimide tape. Polyimide tape (12 mm x 12 mm) 4-41 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
TP1.7 x 5 (Tightening torque = 0.16 ± 0.01N · m ) Make the bending form of LF-2126 Flexible Board. valley fold LF-2126 Flexible Board valley fold Attach the Main Flexible Assy (0030) as shown in the figure. 4-42 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 101
Match the three bosses and attach the Main Flexible Assy (0030). Match the two bosses and attach the Sheet Metal (F (0030A)) with the screw. Main Flexible Assy (0030) TP1.4 x 4 (Tightening torque = 0.12 ± 0.01N · m) Sheet Metal (F (0030A)) Boss Bosses 4-43 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 102
11. Match the Motor B Block Assy and assemble it with three screws as shown in the figure. Motor B Block Assy M1.7 x 2.5 (Tightening torque = 0.16 ± 0.01N · m) 12. Stick on the Adhesive Sheet (5 mm x 5 mm) to the Motor A Flexible Board. 4-44 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 103
15. Stick on the Adhesive Sheet to the LF-2130 Flexible Board. 16. Connect the LF-2130 Flexible Board to the connector on the CM-1017 board and stick on it as shown in the figure. LF-2130 Flexible Board Claw 12 mm Adhesive Sheet CM-1017 Board 4-45 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 104
M1.7 x 2.5 (Tightening torque M1.7 x 2.5 (Tightening torque = 0.16 ± 0.01N · m) = 0.16 ± 0.01N · m) 19. Stick on the Adhesive Sheet to the Motor A Flexible Board and Motor B Flexible Board. 4-46 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 105
24. Connect the Motor A Flexible Board and Motor B Flexible Board to the connector on the Main Flexible Assy (0030). 25. Match the Main Flexible Assy (0030) to the bosses and assemble it with the screw as shown in the figure. 4-47 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 106
27. Attach the Hook and Claws of Front Ornament (1820) in the order and secure it with the screw. TP1.4 x 4 (Tightening torque = 0.12 ± 0.01N · m) Front Ornament (1820) Claws Hook 28. Attach the Retaining Ring E-2.5. Retaining Ring E-2.5 4-48 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
4-584-085-71 * Help Guide (FINNISH) 4-586-523-91 * Operating Guide (ARABIC, PERSI- 4-584-085-81 * Help Guide (TURKISH) 4-584-085-91 * Help Guide (SIMPLIFIED CHINESE) 4-586-524-11 * Operating Guide (TURKISH) 4-584-086-11 * Help Guide (TRADITIONAL CHINESE) 4-586-524-21 * Operating Guide (INDONESIAN) 5-18 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...
Page 125
Except Japanese Model Ref. No. or Q'ty Part No. SP Description 4-584-086-21 * Help Guide (KOREAN) 4-584-086-31 * Help Guide (ARABIC) 4-584-086-41 * Help Guide (PERSIAN) 4-584-086-51 * Help Guide (THAI) 4-584-086-61 * Help Guide (INDONESIAN) 5-19 FDR-AX40/FDR-AX53/FDR-AX55/FDR-AXP55...