Page 2
Stránka č. 1 z 1 2.15.3.2 CLEANING THE THERMAL HEAD AND BLACK BAR TOP PREVIOUS NEXT If dirty patterns or black or white bands appear on a copied or received document, clean the thermal head. Disconnect the power cord and the telephone line cord. Open the front cover by pulling up the center part.
Page 3
Stránka č. 1 z 1 3.3.1 OUTLINE TOP PREVIOUS NEXT Troubleshooting is for recovering quality and reliability by determining the broken component and replacing, adjusting or cleaning it as required. First, determine the problem then decide the troubleshooting method. If you have difficulty findingthe broken part, determine which board is broken.
Page 4
Stránka č. 1 z 1 3.3.2 STARTING TROUBLESHOOTING TOP PREVIOUS NEXT Determine the symptom and the troubleshooting method. CROSS REFERENCE: USER RECOVERABLE ERRORS SIMPLE CHECK LIST DIGITAL BOARD SECTION POWER SUPPLY BOARD SECTION TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 5
Stránka č. 1 z 1 3.3.3 TROUBLESHOOTING ITEMS TABLE TOP PREVIOUS NEXT ITEM SYMPTOM REFERENCE The document does not feed. NO DOCUMENT FEED (Auto Document Document jam DOCUMENT JAM Feeder) Multiple feed MULTIPLE FEED Skew SKEW Recording paper feed The recording paper does not feed. THE RECORDING PAPER DOES NOT FEED Paper jam PAPER JAM...
Page 6
Stránka č. 1 z 1 3.3.3.1 SIMPLE CHECK LIST TOP PREVIOUS NEXT SERIAL NO. DATE FUNCTION JUDGEMENT REFERENCE FAX operation Transmission OK / NG Receiving OK / NG Copy operation OK / NG Telephone operation Handset transceiver / receiver OK / NG SP-PHONE sound OK / NG Ringer sound...
Page 7
Stránka č. 1 z 2 3.3.4.1 NO DOCUMENT FEED TOP PREVIOUS NEXT CROSS REFERENCE: DIGITAL BOARD SECTION POWER SUPPLY BOARD SECTION SENSOR SECTION TEST FUNCTIONS file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Page 8
Stránka č. 2 z 2 ADJUSTMENTS DISASSEMBLY INSTRUCTIONS STEPPING MOTOR DRIVE CIRCUIT Note: When using thin paper etc., sometimes the document will not feed. Refer to ADJUSTING THE FEEDER PRESSURE TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Page 9
Stránka č. 1 z 1 3.3.4.2 DOCUMENT JAM TOP PREVIOUS NEXT CROSS REFERENCE: SENSOR SECTION TEST FUNCTIONS DISASSEMBLY INSTRUCTIONS TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Page 10
Stránka č. 1 z 2 3.3.4.3 MULTIPLE FEED TOP PREVIOUS NEXT When using thick paper etc., sometimes the document will not be fed. Refer to ADJUSTING THE FEEDER PRESSURE Fig. B CROSS REFERENCE: MAINTENANCE DISASSEMBLY INSTRUCTIONS Note: file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Page 11
Stránka č. 2 z 2 When confirming if the characters are extended or distorted, or if the feed problem is occurred, use this test chart format (Fig. B). TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Page 12
Stránka č. 1 z 1 3.3.4.4 SKEW TOP PREVIOUS NEXT * We recommend making a copy of the Fig. B document in MULTIPLE FEED () and using it. CROSS REFERENCE: MAINTENANCE CHECK ITEMS/COMPONENT LOCATIONS DISASSEMBLY INSTRUCTIONS TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27.
Page 13
Stránka č. 1 z 2 3.3.4.5 THE RECORDING PAPER DOES NOT FEED TOP PREVIOUS NEXT * We recommend making a copy of the Fig. B document in MULTIPLE FEED ()and using it. CROSS REFERENCE: INSTALLING THE RECORDING PAPER DIGITAL BOARD SECTION file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN...
Page 14
Stránka č. 2 z 2 POWER SUPPLY BOARD SECTION SENSOR SECTION TEST FUNCTIONS DISASSEMBLY INSTRUCTIONS HOW TO REMOVE THE CASSETTE TRAY BACK COVER SECTION TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Page 15
Stránka č. 1 z 2 3.3.4.5 THE RECORDING PAPER DOES NOT FEED TOP PREVIOUS NEXT * We recommend making a copy of the Fig. B document in MULTIPLE FEED ()and using it. CROSS REFERENCE: INSTALLING THE RECORDING PAPER DIGITAL BOARD SECTION file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN...
Page 16
Stránka č. 2 z 2 POWER SUPPLY BOARD SECTION SENSOR SECTION TEST FUNCTIONS DISASSEMBLY INSTRUCTIONS HOW TO REMOVE THE CASSETTE TRAY BACK COVER SECTION TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Page 17
Stránka č. 1 z 1 3.3.4.6 PAPER JAM TOP PREVIOUS NEXT CROSS REFERENCE: LCD MESSAGES SENSOR SECTION TEST FUNCTIONS DISASSEMBLY INSTRUCTIONS SENSORS AND SWITCHES TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Page 18
Stránka č. 1 z 1 3.3.4.7 MULTIPLE FEED AND SKEW TOP PREVIOUS NEXT CROSS REFERENCE: DISASSEMBLY INSTRUCTIONS OPERATION PANEL SECTION TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 19
Stránka č. 1 z 1 3.3.4.8 THE SENT FAX DATA IS SKEWED TOP PREVIOUS NEXT * We recommend making a copy of the Fig. B document in MULTIPLE FEED () and using it. CROSS REFERENCE: SKEW TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27.
Page 20
Stránka č. 1 z 1 3.3.4.9 THE RECEIVED FAX DATA IS SKEWED TOP PREVIOUS NEXT * We recommend making a copy of the Fig. B document in MULTIPLE FEED () and using it. CROSS REFERENCE: MULTIPLE FEED AND SKEW TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN...
Page 21
Stránka č. 1 z 1 3.3.4.10 RECEIVED OR COPIED DATA IS EXPANDED TOP PREVIOUS NEXT * We recommend making a copy of the Fig. B document in MULTIPLE FEED () and using it. CROSS REFERENCE: DISASSEMBLY INSTRUCTIONS TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN...
Page 22
Stránka č. 1 z 2 3.3.4.11 A BLANK PAGE IS COPIED TOP PREVIOUS NEXT * We recommend making a copy of the Fig. B document in MULTIPLE FEED () and using it. CROSS REFERENCE: A BLANK PAGE IS RECEIVED TEST FUNCTIONS DISASSEMBLY INSTRUCTIONS THERMAL HEAD file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN...
Page 23
Stránka č. 2 z 2 Fig. C TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Page 24
Stránka č. 1 z 1 3.3.4.12 A BLANK PAGE IS RECEIVED TOP PREVIOUS NEXT CROSS REFERENCE: A BLANK PAGE IS COPIED ANALOG BOARD SECTION TEST FUNCTIONS TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 25
Stránka č. 1 z 1 3.3.4.13 BLACK OR WHITE VERTICAL LINE TOP PREVIOUS NEXT * We recommend making a copy of the Fig. B document in MULTIPLE FEED () and using it. CROSS REFERENCE: CLEANING THE THERMAL HEAD AND BLACK BAR DISASSEMBLY INSTRUCTIONS TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN...
Page 26
Stránka č. 1 z 1 3.3.4.14 BLACK OR WHITE LATERAL LINE ON PRINT OUT TOP PREVIOUS NEXT * We recommend making a copy of the Fig. B document in MULTIPLE FEED () and using it. CROSS REFERENCE: A BLANK PAGE IS COPIED DIGITAL BOARD SECTION TEST FUNCTIONS DISASSEMBLY INSTRUCTIONS...
Page 27
Stránka č. 1 z 1 3.3.4.15 AN ABNORMAL IMAGE IS PRINTED TOP PREVIOUS NEXT * We recommend making a copy of the Fig. B document in MULTIPLE FEED () and using it. CROSS REFERENCE: ANALOG BOARD SECTION TEST FUNCTIONS DISASSEMBLY INSTRUCTIONS TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN...
Stránka č. 1 z 1 3.3.5 COMMUNICATION SECTION TOP PREVIOUS NEXT Find the problem in the table shown below, and refer to the corresponding troubleshooting procedure DEFECTIVE FACSIMILE SECTION Symptom Content Possible cause The paper is not fed properly when faxing. Troubleshooting Problem with the feeding (Nor in the copy mode.)
Stránka č. 1 z 1 3.3.5.1.1 TRANSMIT PROBLEM TOP PREVIOUS NEXT CROSS REFERENCE: LCD MESSAGES MAINTENANCE ADF (Auto Document Feed) SECTION OPERATION PANEL SECTION TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Stránka č. 1 z 2 3.3.5.1.2 SOMETIME THERE IS A TRANSMIT PROBLEM TOP PREVIOUS NEXT Note: "596: Transmit level set" represents a service code. (Refer to SERVICE FUNCTION TABLE ().) CROSS REFERENCE: LCD MESSAGES file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004...
Stránka č. 1 z 2 3.3.5.1.3 RECEIVE PROBLEM TOP PREVIOUS NEXT First confirm whether the recording paper is installed properly or not before starting troubleshooting. (Refer to " Remarks ".) Note: "596: Transmit level set" represents a service code. (Refer to SERVICE FUNCTION TABLE ().) Remarks:...
Page 32
Stránka č. 2 z 2 LCD display messages indicating the error causes are shown below. (Refer to LCD MESSAGES CHECK PAPER COVER OPEN UNIT OVERHEATED (COVER OPEN, etc.)...Reset the unit. PAPER JAMMED CHECK FILM Please refer to USER RECOVERABLE ERRORS () for the above items.
Stránka č. 1 z 1 3.3.5.1.4 THE UNIT CAN COPY, BUT CANNOT TRANSMIT/RECEIVE TOP PREVIOUS NEXT CROSS REFERENCE: ANALOG BOARD SECTION TEST FUNCTIONS TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Stránka č. 1 z 4 3.3.5.1.5 THE UNIT CAN COPY, BUT CANNOT EITHER TRANSMIT/RECEIVE LONG DISTANCE OR INTERNATIONL COMMUNICATIONS TOP PREVIOUS NEXT The following two causes can be considered for this symptom. Cause 1: The other party is executing automatic dialing, the call has been received by this unit, and the CED or DIS signal response time is too long.
Page 35
Stránka č. 2 z 4 (Echo/Echo Canceler) The signal from FAX1 reaches FAX2 via stations 1 and 2, but the reflection signal at station 2 also returns via station 1 (echo). As the distance between station 1 and station 2 is far, the echo returns to FAX 1 at a max of 600 msec after transmission.There is a possibility that this signal is detected erroneously as the signal from FAX2.
Page 36
Stránka č. 3 z 4 Fig. c (Countermeasure by Changing the Interval Between CED and DIS) Fig. d (C3ountemeasure by Ignoring the 1st DIS) <TX side signal> <RX side signal> <Countermeasure> 2nd / 3rd DCS / Training & delayed CFR / FTT at TX side 2nd / 3rd EOP / EOM / MPS &...
Stránka č. 1 z 1 3.3.5.1.6 THE UNIT CAN COPY, BUT THE TRANSMISSION AND RECEPTION IMAGE ARE INCORRECT TOP PREVIOUS NEXT (Long distance or international communication operation) This symptom highly depends on the transmission and reception capability of the other FAX unit and the line conditions.
Stránka č. 1 z 2 3.3.5.1.7 HOW TO RECORD FAX SIGNAL BY USING PC TOP PREVIOUS NEXT Recording FAX signal is one of the useful analysis measures to solve communication problems. The way of recording easily by using PC is shown as follows. 1.
Page 39
Stránka č. 2 z 2 4. PC setting and recording 1. Set LINE IN to be valid in the volume control setting. Refer to the PC instruction book. 2. Start up the PC software “ SOUND RECORDER”. (This software is bundled to Windows OS, which can create WAV file.) Set the audio format “...
Stránka č. 1 z 10 3.3.5.1.8 HOW TO OUTPUT THE JOURNAL REPORT TOP PREVIOUS NEXT Refer to BUTTON CODE TABLE ( for KX-FM90HG-W) 1. Press 2 times. 2. Rotate until the “ Journal ” is displayed. 3. Press button. 4. The report prints out. Error code table: Refer to ERROR CODE TABLE...
Page 41
Stránka č. 2 z 10 COMMUNICATION ERROR Reception is not EOP, EOM PIP, PIN, RTP or RTN. COMMUNICATION ERROR No response at the other party after MCF or CFR is transmitted. ERROR-NOT YOUR UNIT DCN is received after CFR transmission. COMMUNICATION ERROR Carrier is cut when the image signal is received.
Page 42
Stránka č. 3 z 10 file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 43
Stránka č. 4 z 10 CROSS REFERENCE: TEST FUNCTIONS file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 44
Stránka č. 5 z 10 CROSS REFERENCE: TEST FUNCTIONS file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 45
Stránka č. 6 z 10 CROSS REFERENCE: TEST FUNCTIONS file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 46
Stránka č. 7 z 10 CROSS REFERENCE: TEST FUNCTIONS file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 47
Stránka č. 8 z 10 file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 48
Stránka č. 9 z 10 file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 49
Stránka č. 10 z 10 CROSS REFERENCE: TEST FUNCTIONS TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Stránka č. 1 z 1 3.3.5.2 REMOTE PROGRAMMING TOP PREVIOUS NEXT If, after the call is connected, the customer describes the situation and it is determined that the problem can be corrected by making parameter changes, this function makes it possible to change parameters such as the user codeand service code from another fax (using DTMF tones).
Stránka č. 1 z 1 3.3.5.2.1 ENTERING THE REMOTE PROGRAMMING MODE AND CHANGING SERVICE CODES TOP PREVIOUS NEXT CROSS REFERENCE: PROGRAM MODE TABLE TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Stránka č. 1 z 6 3.3.5.2.2 PROGRAM MODE TABLE TOP PREVIOUS NEXT KX-FM90CE-W Code Function Set Value Default Remote Setting Set date and time dd/mm/yy hh:mm 01/Jan/00 Your logo (Slovakia only) --------- None Your fax number (Slovakia only) --------- None Transmission report mode 1:ERROR / 2:ON / 3:OFF ERROR...
Page 53
Stránka č. 2 z 6 Vox mode 1:ON / 2:OFF CED frequency select 1:2100Hz / 2:1100Hz 2100 International mode select 1:ON / 2:OFF Auto standby select 1:ON / 2:OFF Receive equalizer select 1:0km / 2:1.8km / 3:3.6km / 4:7.2km Transmission equalizer select 1:0km / 2:1.8km / 3:3.6km / 4:7.2km Setting the number of times that message transfer is redialed.
Page 54
Stránka č. 3 z 6 T4 timer 00~99 x 100ms Monitoring of message transfer 1:ON / 2:OFF Voice prompt 1:Start --------- Sensor & VOX test --------- --------- Digital SP-Phone RX & TX check 1:SP-Phone --------- Print test pattern --------- --------- Top margin Left margin A4 size set...
Page 55
Stránka č. 4 z 6 LCD contrast NORMAL / DARKER NORMAL Remote FAX activation code ON / OFF ON ID=*9 Message alert 1:ON / 2:OFF REC. time alert 1:ON / 2:OFF Receive alert 1:ON / 2:OFF Friendly receive 1:ON / 2:OFF FAX voice guidance 1:ON / 2:OFF Language...
Page 56
Stránka č. 5 z 6 FAX auto redial time set 00~99 FAX auto redial line disconnection time set 001~999sec CNG transmit select 1:OFF / 2:ALL / 3:AUTO Time between CED and 300 bps 1:75ms / 2:500ms / 3:1sec 75ms Overseas DIS detection 1:1st / 2:2nd Receive error limit value 001~999...
Page 57
Stránka č. 6 z 6 Example: If you want to set value in the "004 Transmission report mode", press the dial key number 1,2 or 3 corresponding to the Set Value you want to select. (1:ERROR/2:ON/3:OFF) TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27.
Page 58
Stránka č. 1 z 6 3.3.6.1 DIGITAL BLOCK DIAGRAM TOP PREVIOUS NEXT You also need to check the signal lines listed here [List 1] when the unit fails to boot up the system. Those signal lines should remain normal. Other signal lines are not directly related to that failure even if they have faultsor troubles.
Page 59
Stránka č. 2 z 6 Normal Wave Patterns file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 60
Stránka č. 3 z 6 Remarks: When you use an oscilloscope to judge whether a signal to be tested is normal or NG, perform the signal check in exactly the same order as in [List 1]. (If the ASIC fails to access the ROM, the ASIC cannot access SRAM or DRAM normally.) The digital circuit actually operates according to the timing combinations of these signals.
Page 61
Stránka č. 4 z 6 I/O and Pin No. Diagram After the power is turned on, the ASIC initializes and checks each IC. The ROM, SRAM, and modem are checked. If initialization fails for the ICs , the system will not boot up. In this case, please find the cause as follows.
Page 62
Stránka č. 5 z 6 CROSS REFERENCE: NG EXAMPLE CHECK THE STATUS OF THE DIGITAL BOARD POWER SUPPLY BOARD SECTION file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 63
Stránka č. 6 z 6 CROSS REFERENCE: CHECK THE STATUS OF THE DIGITAL BOARD Other NG example while the power is ON and the LCD displays the following. Refer to LCD MESSAGES TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 64
Stránka č. 1 z 6 3.3.6.1 DIGITAL BLOCK DIAGRAM TOP PREVIOUS NEXT You also need to check the signal lines listed here [List 1] when the unit fails to boot up the system. Those signal lines should remain normal. Other signal lines are not directly related to that failure even if they have faultsor troubles.
Page 65
Stránka č. 2 z 6 Normal Wave Patterns file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 66
Stránka č. 1 z 1 3.3.6.2 FLASH MEMORY (IC512) TOP PREVIOUS NEXT If the unit is working correctly but the VOICE GUIDANCE (voice prompt) is not audible, you should check the Flash Memory. A voice message is pre-recorded in the Flash Memory (IC512). So, when you find an IC512 malfunction and replace it with a new one.
Page 67
Stránka č. 3 z 6 Remarks: When you use an oscilloscope to judge whether a signal to be tested is normal or NG, perform the signal check in exactly the same order as in [List 1]. (If the ASIC fails to access the ROM, the ASIC cannot access SRAM or DRAM normally.) The digital circuit actually operates according to the timing combinations of these signals.
Page 68
Stránka č. 4 z 6 I/O and Pin No. Diagram After the power is turned on, the ASIC initializes and checks each IC. The ROM, SRAM, and modem are checked. If initialization fails for the ICs , the system will not boot up. In this case, please find the cause as follows.
Page 69
Stránka č. 5 z 6 CROSS REFERENCE: NG EXAMPLE CHECK THE STATUS OF THE DIGITAL BOARD POWER SUPPLY BOARD SECTION file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 70
Stránka č. 6 z 6 CROSS REFERENCE: CHECK THE STATUS OF THE DIGITAL BOARD Other NG example while the power is ON and the LCD displays the following. Refer to LCD MESSAGES TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 71
Stránka č. 1 z 1 3.3.11.1 NO KEY OPERATION TOP PREVIOUS NEXT CROSS REFERENCE: TEST FUNCTIONS TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 72
Stránka č. 1 z 1 3.3.11.2 NO LCD INDICATION TOP PREVIOUS NEXT CROSS REFERENCE: TEST FUNCTIONS TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 73
Stránka č. 1 z 1 3.3.12.1 CHECK THE DOCUMENT TOP SW (SW353)...."REMOVE DOCUMENT" TOP PREVIOUS NEXT Refer to LCD MESSAGES TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 74
Stránka č. 1 z 1 3.3.12.2 CHECK THE DOCUMENT SET SW (SW352)...."CHECK DOCUMENT" TOP PREVIOUS NEXT Refer to LCD MESSAGES TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 75
Stránka č. 1 z 1 3.3.12.3 CHECK THE COVER OPEN AND THE FILM END SW (SW501)...."COVER OPEN or CHECK FILM" TOP PREVIOUS NEXT Refer to LCD MESSAGES TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 76
Stránka č. 1 z 1 3.3.12.4 CHECK THE HOOK SWITCH (SW101) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 77
Stránka č. 1 z 1 3.3.12.5 CHECK THE PAPER TOP SENSOR (PS501)......"PAPER JAMMED" TOP PREVIOUS NEXT Refer to LCD MESSAGES TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 78
Stránka č. 1 z 2 3.3.13 CIS (Contact Image Sensor) SECTION TOP PREVIOUS NEXT Refer to SCANNING BLOCK CROSS REFERENCE: TEST FUNCTIONS file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 79
Stránka č. 2 z 2 TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 80
Stránka č. 1 z 1 3.3.14 THERMAL HEAD SECTION TOP PREVIOUS NEXT Refer to THERMAL HEAD TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 81
Stránka č. 1 z 1 3.4.1 INSTALLING PANA LINK SOFTWARE TOP PREVIOUS NEXT Note: The screens shown in these instruction are from WIndows Me. The screens may differ slightly from those of the actual product. The screens are subject to change for improvement without notice. 1.
Page 82
Stránka č. 1 z 1 3.4.2 ACTIVATING PANA LINK SOFTWARE TOP PREVIOUS NEXT 1. Click [Start] in Windows. 2. Point to [Programs] , point to [PANA LINK] and click [PANA LINK] The main panel will appear. ¡ TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN...
Page 83
Stránka č. 1 z 1 3.5.2 OPERATION FLOW TOP PREVIOUS NEXT Refer to LCD MESSAGES TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 84
Stránka č. 1 z 2 3.5.3.1 KX-FM90CE-W ( for Czech) TOP PREVIOUS NEXT Note: The above values are the default values except #48, #68, #74. file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 85
Stránka č. 1 z 2 3.5.3.2 KX-FM90CE-W ( for Slovakia) TOP PREVIOUS NEXT Note: The above values are the default values except #48, #68, #74. file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 86
Stránka č. 1 z 2 3.5.3.3 KX-FM90HG-W TOP PREVIOUS NEXT Note: The above values are the default values except #48, #68, #74. file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 87
Stránka č. 1 z 3 3.5.4.1 KX-FM90CE-W TOP PREVIOUS NEXT Code Function Set Value Effective Default Remarks Range Your logo (Slovakia ---------- ---------- --------- Refer to KX-FM90CE-W (for Slovakia) only) Your fax number ---------- ---------- --------- Refer to KX-FM90CE-W (for Slovakia) (Slovakia only) Pause time set X 100 msec...
Page 88
Stránka č. 2 z 3 Remote turn-on ring X number of 01~99 Sets the number of rings before the unit starts to receive a document in the TEL mode. number set rings OFF-Hook alarm 1:ON 2:OFF 1, 2 ---------- option TAM continuous 1:ON 2:OFF 1, 2...
Page 89
Stránka č. 3 z 3 Digital SP-phone DIGITAL SPEAKERPHONE check Print test pattern TEST FUNCTIONS Top margin ---------- Left margin ---------- A4 size set 1:ON 2:OFF 1, 2 ---------- Serial port self test 1:OK 2:NG 1, 2 This is the PC interface circuit test mode. History list HISTORY Journal 2 list...
Page 90
Stránka č. 1 z 3 3.5.4.2 KX-FM90HG-W TOP PREVIOUS NEXT Code Function Set Value Effective Default Remarks Range Your logo ---------- ---------- --------- Refer to KX-FM90CE-W (for Czech) / KX-FM90HG-W Your fax number ---------- ---------- --------- Refer to KX-FM90CE-W (for Czech) / KX-FM90HG-W Pause time set X 100 msec 001~600...
Page 91
Stránka č. 2 z 3 Remote turn-on ring X number of 01~99 Sets the number of rings before the unit starts to receive a document in the TEL mode. number set rings OFF-Hook alarm 1:ON 2:OFF 1, 2 ---------- option TAM continuous 1:ON 2:OFF 1, 2...
Page 92
Stránka č. 3 z 3 Digital SP-phone DIGITAL SPEAKERPHONE check Print test pattern TEST FUNCTIONS Top margin ---------- Left margin ---------- A4 size set 1:ON 2:OFF 1, 2 ---------- Serial port self test 1:OK 2:NG 1, 2 This is the PC interface circuit test mode. History list HISTORY Journal 2 list...
Page 93
Stránka č. 1 z 1 3.5.5.1 KX-FM90CE-W TOP PREVIOUS NEXT TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...
Page 94
Stránka č. 1 z 2 3.5.7 SPECIAL SERVICE JOURNAL REPORTS TOP PREVIOUS NEXT Journal 2 and Journal 3 shown below, which are special journals giving the additional detailed information about the latest 35 communications, can be printed by Service Code 881 or 882. Remote printing function for the journalreports (JOURNAL, JOURNAL 2 and JOURNAL 3) is also available for service technicians.
Page 95
Stránka č. 2 z 2 * MAKER CODE: 79 2. Look at NO. 04 in the JOURNAL 2. CNG (0003) indicates that the CNG signal has been received three times since the purchase date. For further details, see JOURNAL 2 () and JOURNAL 3 3.5.7.1 JOURNAL 2...
Page 96
Stránka č. 1 z 2 3.5.7.1 JOURNAL 2 TOP PREVIOUS NEXT Refer to JOURNAL 2 in PRINTOUT EXAMPLE Journal 2 displays the additional detailed information about the last 35 communications. Descriptions: (1) RCV. MODE Indicates which receive mode the unit was in when the unit received a fax message. This information is also displayed when the unit transmitted a fax message.
Page 97
Stránka č. 2 z 2 received in memory due to "PAPER OUT" error. [NO RESPONSE DISAPPEARED ON JOURNAL] The " NO RESPONSE DISAPPEARED ON JOURNAL " displays the information about the last 10 communications terminated by "No Response". (Some of the communications terminated by "No Response"...
Page 98
Stránka č. 1 z 1 3.5.7.2 JOURNAL 3 TOP PREVIOUS NEXT Refer to JOURNAL 3 in PRINTOUT EXAMPLE Descriptions: (6) ENCODE Compression Code: MH/MR/MMR (7) MSLT MSLT means Minimum Scan Line Time. Used only at the factory. (8) EQM EQM means Eye Quality Monitor. Used only at the factory. (9) ERROR LINE(RX) When an error occurs while receiving a fax, this shows the number of error lines.
Page 99
Stránka č. 1 z 2 3.6 TEST FUNCTIONS TOP PREVIOUS NEXT The codes listed below can be used to perform simple checks of some of the unit’s functions. When complaints are received from customers, they provide an effective tool for identifying the locations and causes of malfunctions.
Page 100
Stránka č. 2 z 2 :Detection signal for the tone on the line. Turns on when there is a tone signal on the line. Note: The numbers in the boxes (XXX) indicate the keys to be input for the various test modes. 3.6.1 DTMF SINGLE TONE TRANSMIT SELECTION 3.6.2 BUTTON CODE TABLE 3.6.3 PRINT TEST PATTERN...
Page 101
Stránka č. 1 z 1 3.6.1 DTMF SINGLE TONE TRANSMIT SELECTION TOP PREVIOUS NEXT When set to ON (=1), the 12 keys and transmission frequencies are as shown. key High Frequency (Hz) key Low Frequency (Hz) “1” “5” 1209 “2” “6”...
Page 102
Stránka č. 1 z 1 3.6.2 BUTTON CODE TABLE TOP PREVIOUS NEXT Code Button Name Code Button Name Code Button Name RESOLUTION VOLUME START / COPY / SET 26 VOLUME LOWER REDIAL / PAUSE SP-PHONE FLASH MUTE CALLER ID (KX-FM90HG only) AUTO ANSWER QUICK SCAN RECORD...
Page 103
Stránka č. 1 z 1 3.5.5.2 KX-FM90HG-W TOP PREVIOUS NEXT TOP PREVIOUS NEXT file://C:\Documents%20and%20Settings\Admin\Plocha\SCHÉMATA\VIDEA\PAN... 27. 10. 2004 http://servis-manual.com/...