Related Manuals for Dell MXG610s
Summary of Contents for Dell MXG610s
- Page 1 MXG610s Fibre Channel Switch Module Setup Guide Supporting fabric OS 8.1.0_Inx and 9.0.1a May 2021 Rev. A01...
- Page 2 A WARNING indicates a potential for property damage, personal injury, or death. © 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.
-
Page 3: Table Of Contents
Contents Chapter 1: About this guide......................4 Chapter 2: MXG610s Setup Guide....................5 MX7000 chassis preparation............................5 Switch module installation..............................5 Serial connection................................. 6 Optical transceivers and cabling installation......................... 7 Port-side LEDs..................................7 Static IP addresses................................8 Additional country-specific IEEE notices........................11 Chapter 3: Dell EMC support......................13... -
Page 4: Chapter 1: About This Guide
About this guide This guide provides site preparation recommendations, step-by-step procedures for rack mounting and desk mounting, inserting modules, and connecting to a power source. CAUTION: To avoid electrostatic discharge (ESD) damage, wear grounding wrist straps when handling this equipment. NOTE: Only trained and qualified personnel can install this equipment. -
Page 5: Chapter 2: Mxg610S Setup Guide
MXG610s Setup Guide Topics: • MX7000 chassis preparation • Switch module installation • Serial connection • Optical transceivers and cabling installation • Port-side LEDs • Static IP addresses • Additional country-specific IEEE notices MX7000 chassis preparation Before you insert the switch module in the MX7000 chassis, meet the following conditions: ●... -
Page 6: Serial Connection
4. Start from port 0, then port 17, and then the rest of the ports when cabling the SFP+ ports. You are now ready to insert more SFP+/QSFP optical transceivers, if needed. Be sure to use only Brocade-branded SFP+/QSFP optical transceivers. The MXG610s does not recognize non-Broadcom products. Serial connection To log in to the switch module through the serial connection on the front panel, perform the following steps: 1. -
Page 7: Optical Transceivers And Cabling Installation
Cable connectors are keyed to ensure correct orientation. If a cable connector does not install easily, ensure that it is correctly oriented. For instructions specific to a cable type, see the cable manufacturer’s documentation. Port-side LEDs Each switch module uses bicolored external LEDs to indicate operation status. MXG610s Setup Guide... -
Page 8: Static Ip Addresses
Static IP addresses Dell EMC recommends configuring the switch module through the Dell EMC OpenManage Enterprise — Modular (OME-M) graphical user interface (GUI). Use this management GUI to configure the switch IP address, host name, and password. By default, the IP address mode is set to DHCP. Use the GUI to assign a static IP address. To configure the FC switch module, follow these steps: 1. - Page 9 The Overview tab is displayed. Select the Settings tab. 4. Click and expand the Network option. Select the required check boxes, and complete the IPv4 or IPv6 settings, DNS server settings, and optionally the management VLAN ID. Click Apply. MXG610s Setup Guide...
- Page 10 5. Click and expand the Management option. Specify a hostname and root password. Click Apply. 6. Click and expand the Monitoring option. Select the Enable SNMP check box, the SNMP version, and enter a read community string. Click Apply. MXG610s Setup Guide...
-
Page 11: Additional Country-Specific Ieee Notices
7. Click and expand the Advanced Settings option. Select the needed check boxes. 8. Click Apply. You have configured the IP address and other settings for the switch module. Additional country-specific IEEE notices MXG610s Setup Guide... - Page 12 MXG610s Setup Guide...
-
Page 13: Chapter 3: Dell Emc Support
Dell EMC support The Dell EMC support site provides documents and tools to help you use Dell EMC equipment and mitigate network outages. Through the support site you can obtain technical information, access software upgrades and patches, download available management software, and manage your open cases. The Dell EMC support site provides integrated, secure access to these services.