Page 1
Operator's manual ® HUSQVARNA AUTOMOWER 550H EPOS EN, English Read the operator's manual carefully and make sure that you understand the instructions before you use the product.
Contents 6.4 LED indicator lamp on the charging station..34 1 Introduction 6.5 LED indicator lamp on the product......34 1.1 Support..............3 6.6 Symptoms............35 1.2 System description..........3 7 Transportation, storage and disposal 1.3 Product description..........3 1.4 System overview........... 4 7.1 Transportation.............
The operator selects the operation settings in the ® Automower Connect app. The app shows the selected For support about the product, speak to your Husqvarna and possible operation settings, and the operation mode servicing dealer. of the product. 1.2 System description 1.3.1 Mowing technique...
1.4 System overview Navigation satellites Stay-out zone Satellite signals Work area Reference station Mobile device Correction data 10. Docking point Charging station 11. Transport path Virtual boundary Purchased separately. Not included. 4 - Introduction 1619 - 002 - 19.01.2021...
1.5 Product overview Body 16. Low-voltage cable LED indicator lamp of the product 17. Power supply STOP/START button 18. Extra blades Ultrasonic sensors 19. Screws for securing the charging station Front wheels 1.6 Symbols on the product Rear wheels Cutting system These symbols can be found on the product.
WARNING: Read the user in- structions before operating the product. The low-voltage cable must not be shortened, extended or spliced. Do not use a trimmer nearby the low- WARNING: Disable the prod- voltage cable. Be careful when trimming uct before working on or lift- edges where the cables are placed.
Page 7
italics is a text that is in the • Text written in Automower ® Connect app, or is a reference to another section in the Operator’s manual. • Text written in bold is one of the buttons on the product or in appDrive. 1619 - 002 - 19.01.2021 Introduction - 7...
2 Safety 2.1 Safety information 2.1.1 IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE The operator is responsible for accidents or hazards occurring to other people or property. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities (that could affect a safe handling of the product), or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person...
The appliance must be disconnected from the supply mains when removing the battery. WARNING: The product CAUTION: Used if there is a risk of damage to the product, other materials or can be dangerous if used the adjacent area if the instructions in the manual are not obeyed.
Page 10
Schedule on page 20 . Refer to blades hit foreign objects the blades can be • Husqvarna does not guarantee full compatibility damaged. Always switch off the product before between the product and other types of wireless clearing a blockage. Inspect the product for systems such as remote controls, radio damage before starting the product again.
Page 11
2.3.3.1 How to lift the product CAUTION: Never use a high-pressure Push the STOP button to stop the product. washer or even running water to clean the product, charging station and reference station. Never use solvents for cleaning. CAUTION: Use the plug to disconnect the charging station before any cleaning or maintenance of the charging station.
3.4 To examine where to put the reference station Note: Refer to www.husqvarna.com for more Read and understand the instructions about where to information about installation. put the reference station. Refer to the Operator's manual for the reference station.
• If the product must not operate in a part of the docking area, put a protective wall that is minimum 15 cm / 6 in. in height. The docking area (A) is a circular area around the charging station with a radius of 3 m / 9.8 ft.
3.7 To examine where to install the • Make sure that there are no trees with thick vegetation in the areas where the product objects on the map operates. • Make sure the that product can receive radio CAUTION: If the work area is adjacent signals from the reference station in the complete to water bodies, slopes, precipices or a area.
13 . WARNING: The product is only to be used with the power supply unit supplied by Husqvarna. WARNING: min 30 cm / 12” Do not put the power supply at a position where there is a risk that it can become wet.
Page 16
™ more information about Husqvarna Fleet Services refer to www.husqvarna.com. 3.8.4 Installation of the reference station 3.8.6.1 To connect to the product with Husqvarna Fleet Install the reference station according to the instructions ™ Services in the Operator's manual for the reference station.
Page 17
secondary area. Maximum 20 work areas can be Note: ® It is only necessary to pair the Automower installed on a map. Connect app and the product one time. A transport path is a specified path between the docking point in front of the charging station and a work area. 3.8.8 Installation of the map The product can operate automatically in this path, but does not cut grass.
Page 18
Note: The position of the waypoint when you install a work area or a stay-out zone is in the front left corner of the product. Note: Walk 2-3 m / 6.5-9.8 ft. behind the product when you operate the product with appDrive. To make a work area •...
Page 19
• Add the waypoint at the outer corner to install the virtual boundary around a corner. To make a transport path • Operate the product and add waypoints on the map to install a transport path. Start in a work area minimum 1 m / 3.3 ft.
208 / 2240 EPOS Example: A lawn of 3000 m / 32000 ft , cut with an ® Automower 550H EPOS. 3000 m / 208 ≈ 14.5 h. 32000 ft / 2240 ≈ 14.5 h. Days / week h / day Schedule settings 14.5...
Page 21
Settings for accessories mounted on the product can be made in this menu. 3.9.4.1 Headlights There are 4 different headlight settings that control when the headlights are on: Always ON • Evening only (19:00-00:00) • Evening and night (19:00-07:00) • •...
Page 22
3.9.6.2 Change PIN code Note: Messages menu is only available for ® You can change the PIN code in the Automower ® Bluetooth short-range connectivity. Connect app. Make a note of the new PIN code in Introduction on page 3 . Memo.
4 Operation 4.1 Main switch 4.3.2 appDrive Use the appDrive to operate the product manually. WARNING: Read the safety 4.3.2.1 To operate the product with appDrive instructions carefully before you start the product. Use the buttons to operate the product: •...
operation mode is selected and the START button is WARNING: Always switch off the pushed. product using the Main switch if it requires 4.4.2 Select duration maintenance, or if the product must be moved outside the work area. The product goes back to the charging station and stays for the selected park duration.
It is recommended to clean using a brush. Husqvarna recommends to use a special cleaning and maintenance kit, available as an accessory. Speak to your Husqvarna representative for more information.
5.5 Winter service Turn the product upside down. Put the product on a soft and clean surface to avoid scratching the Take your product to your Husqvarna central service for product. service prior to winter storage. Regular winter service Rotate the skid plate so that its holes align with the will maintain the product in good condition and create screws for the blade.
Messages menu in Automower ® All messages can be found in the Connect. More suggestions for steps to take in the event of malfunction or symptoms can be found on www.husqvarna.com. Note: Messages menu is only available for short-range connectivity (Bluetooth ®...
Page 28
Message Cause Action No loop signal The power supply or the low-voltage ca- Examine the LED status on the charging ble for the charging station is not connec- station. If there is no power to the charg- ted. ing station, the LED is not lit. Examine the wall socket connection and if a resid- ual-current device is engaged.
Page 29
Message Cause Action Empty battery The product cannot find the charging sta- The product has no accurate position tion. and cannot find the charging station. There is an obstacle preventing the prod- uct to find the charging station. Battery on The battery is at the end of its life cycle.
Page 30
Message Cause Action Wheel motor blocked right/ Grass or other object is wrapped around Clean the wheels and around the wheels. left the drive wheel. Alarm! Mower stopped The alarm was activated because the Adjust the mower security settings in the product was stopped.
Page 31
Message Cause Action Map problem ® There is no defined work area. Make a work area in the Automower To make a work Connect app. Refer to area on page 18 . The charging station or the reference sta- Move the charging station or the refer- tion has been moved.
Page 32
Message Cause Action Reference station communi- The product is not paired with the refer- Redo the pairing with the reference sta- cation problem ence station. tion. The reference station is not installed cor- Examine the installation of the reference rectly. station.
6.3 Information and warning messages Messages menu in the Automower ® The information messages in the table below are shown in the Connect app. Speak to your Husqvarna representative if the same message shows frequently. Message Cause Action Low battery...
For a fully functional installation, the indicator lamp in the charging station must show a solid or flashing green light. If another color shows, follow the troubleshooting guide below. There is more help on www.husqvarna.com. If you still need help, speak to your local Husqvarna representative. Light...
6.6 Symptoms If your product does not work as expected, follow the symptoms guide below. Symptoms Cause Action The Main switch is set to 0 The Main switch was set to 0 when the Set the Main switch to 1 and connect the ®...
Page 36
Symptoms Cause Action The product is parked for The product is parked due to a schedule Open the app and edit the schedule set- Park until further no- Dashboard and start the hours in the charging station. setting, or because tings, or go to tice has been chosen in the app.
Keep the product in a dry, frost free space. a Torx 20. • Keep the product with all wheels on level ground during storage, or use a Husqvarna wall hanger. • If you keep the charging station indoors, disconnect and remove the power supply from the charging station.
8 Technical data 8.1 Technical data ® Dimensions Automower 550H EPOS Length, cm / in. 75 / 29.5 Width, cm / in. 63 / 24.8 Height, cm / in. 35 / 13.8 Weight, kg / lbs 16 / 35.3 ®...
5 . 8.2 Registered trademarks Bluetooth ® Bluetooth SIG, inc. and any use of such word mark and logos are registered trademarks owned by marks by Husqvarna is under license. 1619 - 002 - 19.01.2021 Technical data - 39...
The blades and wheels are seen as disposable and are not covered by the warranty. If an error occurs with your Husqvarna product, please contact Husqvarna customer service for further instructions. Please have the receipt and the product’s serial number at hand when contacting Husqvarna customer service.
Conformity and on, the user is encouraged to try to correct the interference by one or more of the following measures: Issuer: Husqvarna AB, Drottninggatan 2, S-561 82 • Reorient or relocate the receiving antenna. Huskvarna, Sweden www.husqvarnagroup.com.