Epson EV-115 Setup Manual page 2

Setting Up the Projector
When wiring is complete, set the projector operations according to your environment.
Turn on the projector.
A
Press the [Menu] button on the remote control, and then
B
select [Extended] - [DC Out (2.0A)/GPI In Settings].
Set [DC Out/GPI In] to [Always On/On].
C
When this is set to [On While Project/Off ], the external sensor is
disabled.
Select [GPI-1 Settings] or [GPI-2 Settings].
D
• [GPI-1 Settings]: Sets the operation for the sensor connected to
pin No.2.
• [GPI-2 Settings]: Sets the operation for the sensor connected to
pin No.3.
Set the operation according to the signal input for the
E
external sensor.
• [Low -> High]: Sets the operation performed when a High
level signal is input.
• [High -> Low]: Sets the operation performed when a Low level
signal is input.
Item Description
Power On Turns the projector on or off.
Power Off
Execute A/V Mute Executes or releases A/V Mute. The content
continues to play while A/V Mute is
Release A/V Mute
enabled.
Start Playlist Plays or stops the playlist set in
[Favorite Playlists].
Stop Playlist
Source Select Switches the image source.
Light Source Mode: Normal Switches the Light Source Mode setting.
Light Source Mode: Quiet
F Set more detailed operations.
Item Description
Favorite Set the playlist you want to play when [Low -> High]/
Playlists [High -> Low] are set to [Start Playlist]. Select the
number of the numeric button on the remote control
that is assigned to Favorite Playlists.
Source Set the source you want to switch to when
[Low -> High]/[High -> Low] are set to [Source Select].
Combination When two external sensors are connected, you can set
the status of the other external sensor as the condition
for executing an operation.
For example, if [Combination] in [GPI-1 Settings] is set
to [GPI-2 Low], the operation set in [GPI-1 Settings] is
executed when the GPI-2 signal becomes Low.
Hold High When the external sensor signal is maintained
Hold Low continuously for the set time (mm:ss), the selected
operation is executed.
When you have finished making settings, press the [Menu]
G
button to finish.
You can check the status for the GPI-1 and GPI-2 signals in [GPI Info.]
from [DC Out (2.0A)/GPI In Settings].
Solving Problems
Try the following solutions if you are having trouble connecting or configuring the external sensors.
Status
The set operation is not executed even when a • Check the status of the projector. In the following situations, the signal input from the external sensor
signal is input from an external sensor. is disabled.
• When the menu screen is displayed
• When the projector's indicator is in one of the following conditions:
Warming up, shutting down, or cooling down
• On/Standby: On
• Status: Flashing
• Depending on the operation you have set, it may take some time to execute.
Content starts playing from the middle. Check the content of [GPI-1 Settings]/[GPI-2 Settings].
If you set a combination of [Start Playlist] and [Execute A/V Mute], the content may not be played
correctly. Select [Stop Playlist] instead of [Execute A/V Mute].
You cannot make accurate signal retention time We recommend that you use the [Hold High]/[Hold Low] settings on the projector. Follow the steps
settings using the external sensor's functions. below to make settings.
Use the functions for the external sensor to minimize the amount of time it retains the signal.
A
B Set the time to retain the external sensor's signal in [Hold High] or [Hold Low] in [GPI-1 Settings]/
[GPI-2 Settings].
The set playlist does not play. Check the settings for [GPI-1 Settings]/[GPI-2 Settings] - [Favorite Playlists]. Set the number of the
numeric button on the remote control that is assigned to the playlist you want to play.
Remedy
© 2020 Seiko Epson Corporation
2020.10 Rev.1.0