Philips SQM9222 User Manual

2015 © Gibson Innovations Limited.
All rights reserved.
This product has been manufactured by, and is sold
under the responsibility of Gibson Innovations Ltd., and
Gibson Innovations Ltd. is the warrantor in relation to this
product.
Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used under
license from Koninklijke Philips N.V.
A
G
B
C
H
D
I
E
J
F
6
7
8
sqm9222_27_2L_um_150731.indd 1-3
Register your product and get support at
www.philips.com/support
User manual
Manual del usuario
UM_SQM9222
27_2L_V1.0
WK15315
1
2
4
3
9
11
SQM9222
5
10
E n gl i sh
1 Important safety instructions
Caution
•
Read these instructions before you begin. If you are unsure of any
part of the process, contact a professional contractor or installer for
assistance. Improper installation can result in injury or damage.
•
The wall or mounting surface must be capable of supporting the
combined weight of the mount and the display; if not, the structure
must be reinforced.
•
Locate pipes, wires, or any other hazards in the wall where you wish
to install the mount before drilling.
•
Safety gear and proper tools must be used. Failure to do so can result
in injury or damage.
•
Two people are recommended for installation. Do not attempt to lift
a heavy display without assistance.
•
Follow all instructions and recommendations regarding adequate
ventilation and suitable locations for mounting your display. Consult
the owner's manual for your particular display for more information.
•
This wall mount is intended for use only with the maximum weight of
25 kg (55 lbs). Use with heavier than the maximum weights indicated
may result in instability causing possible injury.
2 Full motion wall mount (for LCD, Plasma, and
LED displays)
What's in the box
Full motion mount (x1) User manual (x1)
Adapter (x4) Hardware kit (x1)
Plastic cover (x2)
Hardward kit
Drywall screw (x2) S10 wrench (x1)
A F
Washer (x6) M4 x 12 screw (x4)
B G
Concrete anchor (x2) M4 x 20 screw (x4)
C H
M6 x 12 screw (x8) M6 x 20 screw (x4)
D I
M6 lock nut (x4) Spacer (x4)
E J
Tools required
•
Phillips head screw driver
•
Electric or portable drill
•
3 mm (1/8") drill bit and stud finder for drywall installation
•
8 mm (5/16") Masonry bit for concrete installation
•
Level
3 Installation
Mount to the drywall
Caution
For safety reasons, this mount must be secured to a wood stud of supporting
the combined weight of the mount and display. Do not mount to drywall alone.
1 Use a high quality stud finder to locate a stud where you wish
to install your mount. Mark both edges of each stud to help
identify the exact center.
Note
You must use the center of the stud to avoid cracking or splitting the
wood during installation.
2 Place the mount against the wall over the marked stud. Make
sure it is level and right side up.
3 Mark two locations (one top and one bottom) at the center of the
stud for securing the mount to the wall (see Fig. 1) and set it aside.
4 Drill a 3 mm (1/8") pilot hole at each marked location.
5 Place the mount back against the wall and attach it using the
drywall screws and two of the washers
A
2). Do not over-tighten these screws. Ensure that the mount
remains level after all screws are secured.
Mount to the concrete wall
Caution
For safety reasons, the concrete wall must be capable of supporting the
combined weight of the mount and the display. The manufacturer takes no
responsibility for failure caused by walls of insufficient strength.
1 Place the mount against the wall in the desired location and
make sure it is level and right side up.
2 Mark two locations (one top and one bottom) for securing the
mount to the wall (see Fig. 3) and set it aside.
3 Drill an 8 mm (5/16") hole at each marked location. Remove
any excess dust from the holes.
4 Insert a concrete anchor
into each hole so that it is flush
C
with the concrete surface (see Fig. 4). A hammer can be used
to lightly tap the anchors into place if necessary.
Note
If the concrete wall is covered by a layer of plaster or drywall, the concrete anchor
must pass completely through the layer to rest flush with the concrete surface.
5 Place the mount back against the wall and attach it using the
drywall screws and two of the washers
A
Fig. 2). Do not over-tighten these screws. Ensure that the
mount remains level after both screws are secured.
Attaching the display plate to the display
Caution
Use extra care during this part of the installation. If possible, avoid facing
down your display as it may damage the viewing surface.
provided (see Fig.
B
provided (see
B
31/07/2015 18:27:03