User Manual SyncMaster S23A750D / S27A750D The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. BN46-00036A-05...
2011 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics.
Page 3
Before Using the Product Activities marked by this symbol are prohibited. Instructions marked by this symbol must be followed. Before Using the Product...
Before Using the Product Cleaning Cleaning Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. Take the following steps when cleaning. 1. Power off the monitor and computer. 2. Disconnect the power cord from the monitor. 3.
High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used nearby. Be sure to contact Samsung Customer Service Center (page 79) if the inside of the monitor needs cleaning. (service fee will be charged).
Page 6
Before Using the Product Warning Do not use a damaged power cord or plug, or a loose power socket. An electric shock or fire may result. Do not plug many products into the same power socket. Otherwise, the socket may overheat and cause a fire. Do not touch the power plug with wet hands.
The product may become damaged by an electric shock. Do not use the power cord for products other than authorized products supplied by Samsung. An electric shock or fire may result. Keep the power socket where the power cord is connected unobstructed.
Page 8
Before Using the Product Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.). The product may fall and break or cause a personal injury. Using the product in an area with excess vibration may damage the product or cause a fire.
Be sure to consult Samsung Customer Service Center (page 79) before installation if you want to install the product at such a place.
Page 10
(paper, match, etc.) into the vent or ports of the product. If water or any foreign substance enters the product, be sure to power off the product, remove the power cord, and contact Samsung Customer Service Center (page 79).
Page 11
Before Using the Product Caution Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels. If you are not going to use the product for an extended period of time, activate power-saving mode or a moving-picture screen saver.
Page 12
Before Using the Product Do not hold the monitor upside-down or move it by holding the stand. The product may fall and break or cause a personal injury. Do not use humidifiers or stoves around the product. An electric shock or fire may result. Rest your eyes for more than 5 minutes for every 1 hour of product use.
Before Using the Product Correct posture to use the product Use the product in the correct posture as follows: Straighten your back. Allow a distance of 45 to 50cm between your eye and the screen, and look slightly downward at the screen. Keep your eyes directly in front of the screen.
Table Of Contents BEFORE USING THE PRODUCT PREPARATIONS Copyright Icons used in this manual Symbols for safety precautions Cleaning Cleaning Securing the Installation Space Precautions for storage Safety Precautions Electricity and Safety Installation Operation Correct posture to use the product Checking the Contents Removing the Packaging Checking the Components...
Page 15
Changing the Resolution Using a PC Connecting to a Video Device Connection Using the HDMI Cable Connecting Headphones MAGIC SAMSUNG MAGIC Angle SAMSUNG MAGIC Bright Configuring SAMSUNG MAGIC Color Brightness Configuring Brightness Contrast Configuring Contrast Sharpness Configuring Sharpness Response Time...
Page 16
Table Of Contents RESIZING OR RELOCATING THE SCREEN SETUP AND RESET Blue Configuring Blue Color Tone Configuring the Color Tone Settings Gamma Configuring Gamma Size Changing the Image Size H-Position Configuring H-Position V-Position Configuring V-Position Menu H-Position Configuring Menu H-Position Menu V-Position Configuring Menu V-Position Eco Motion Sensor...
Page 17
Initializing Settings (Reset) INFORMATION Displaying INFORMATION Configuring Brightness in the Startup Screen Configuring Volume in the Startup Screen Requirements Before Contacting Samsung Customer Service Center GUIDE Testing the Product Checking the Resolution and Frequency Check the followings. Q & A General PowerSaver...
Page 18
Table Of Contents APPENDIX INDEX Contact SAMSUNG WORLDWIDE Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only Terminology Table Of Contents...
Preparations Checking the Contents 1.1.1 Removing the Packaging Open the packaging box. Be careful not to damage the product when you open the packaging with a sharp instrument. Remove the Styrofoam from the product. Check the components and remove the Styrofoam and plastic bag. The appearance of actual components may differ from the image shown.
Preparations 1.1.2 Checking the Components Contact the dealer from whom you purchased the product if any item is missing. The appearance of the components and items sold separately may differ from the image shown. Components Quick Setup guide Cleaning cloth 3D Glasses &...
Preparations Parts 1.2.1 Frontal Buttons The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. If the MENU button is not visible, lightly tap the area around the [ become visible.
Page 22
Preparations Icons Description Open or close the onscreen display (OSD) menu, or return to the last menu. OSD control lock: Maintain the current settings, or lock the OSD control to prevent unintended changes to settings. To lock the OSD control, press the MENU button [ seconds.
Preparations 1.2.2 Reverse Side The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Port 1.2.3 Tidying Up the Connected Cables Tidy up the cables using the cable holder on the back of the stand. POWER DP IN HDMI IN...
Preparations The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. 1.2.4 Kensington Lock An anti-theft lock allows you to use the product securely even in public places. The locking device shape and locking method depend on the manufacturer.
Preparations 1.2.5 Adjusting the Product Tilt The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. You can adjust the tilt of your monitor. Hold the lower part of the product and adjust the tilt carefully. 1 Preparations...
This feature allows you to view 3D content such as 3D movies. You can view 3D content using (SyncMaster-dedicated) Samsung 3D glasses. You can purchase "SyncMaster-dedicated 3D glasses (model name: SSG-M3750CR)" separately. Contact the dealer you purchased the product from for details about purchasing the 3D glasses.
Configuring the 3D Mode Press [ ] on the product. Press [ ] to move to Press [ ] to move to Press [ ] to move to Off: Disable the 3D Mode 3D: Converts a normal video to 3D video. →...
Page 28
Press [ ] to move to appear. L/R Image R/L Image Press [ ] to move to the option you want and press the [ The selected option will be applied. 2.1.3 3D → Activates 2D screen mode. This function is turned off when Configuring the 3D →...
Standard HDMI-Compatible Formats The 3D formats indicated below are recommended by the HDMI association and must be supported. Basic Video Signal 1920x1080p @24Hz 1280x720p @60Hz Resolution Supported for PC Input (via the HDMI Port) PC input is optimized for video in 1920x1080 resolution. If the resolution is not 1920 x 1080, the 3D picture is not properly displayed and you cannot watch the 3D picture in full screen.
For further details about "TriDef 3D Games for SyncMaster(TriDef 3D)": please contact DDD Co., Ltd. www.tridef.com For further details about the product, please contact Samsung Electronics. To find 3D-compatible games, visit www.tridef.com/syncmaster. "SyncMaster 3D Game Launcher(TriDef 3D)" is updated each time new games are added to the list of compatible games.
Connecting and Using a Source Device Before Connecting 3.1.1 Pre-connection Checkpoints Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device. Do not connect the power cable until all connections are completed. Connecting the power cable during connection may damage the product.
Connecting and Using a Source Device Connecting and Using a PC 3.3.1 Connecting to a PC Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. Select a connection method suitable for your PC. Connecting parts may differ in different products.
An installation driver is contained on the CD supplied with the product. If the file provided is faulty, visit the Samsung homepage (http://www.samsung.com) and download the file. Insert the user manual CD provided with the product into the CD-ROM drive.
Connecting and Using a Source Device 3.3.3 Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase. Select a language and change the resolution to the optimum value. The optimal resolution for this monitor is as follows: 1920 x 1080 120Hz Follow the above settings to set the resolution.
Page 35
Connecting and Using a Source Device Changing the Resolution on Windows Vista Go to Control Panel → Changing the Resolution on Windows 7 Go to Control Panel → Personalization → Display Settings and change the resolution. *********** *********** Display → Screen Resolution and change the resolution.
Connecting and Using a Source Device Connecting to a Video Device Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. The product can be connected to a video device. Connecting parts may differ in different products.
Configure the screen settings such as brightness and color tone. MAGIC This feature provides the viewing angle, brightness, and tint to suit your preferences. 4.1.1 SAMSUNG MAGIC Angle Angle allows you to configure the settings to obtain the optimum picture quality according to your viewing angle.
Press [ ] to move to the option you want and press the [ The selected option will be applied. 4.1.2 SAMSUNG MAGIC Bright This menu provides an optimum picture quality suitable for the environment where the product will be used.
The selected option will be applied. 4.1.3 Configuring SAMSUNG MAGIC Color Color is a new picture-quality improvement technology developed independently by Samsung, which delivers vivid natural colors without picture quality degradation. This menu is not available when Not available when...
Screen Setup Demo: Compare normal screen mode with Full: Obtain a vivid picture quality for all areas including the flesh colors in the picture. Intelligent: Improve the chroma for all areas except the flesh colors in the picture. Press [ ] to move to the option you want and press the [ The selected option will be applied.
Screen Setup 4.3.1 Configuring Contrast Press [ ] on the product. Press [ ] to move to Press [ ] to move to Adjust the Contrast Sharpness Make the outline of objects more clear or blurry. (Range: 0~100) A higher value will make the outline of objects clearer. This option is not available when This option is not available when 4.4.1 Configuring Sharpness...
Screen Setup Response Time Accelerate the panel response rate to make video appear more vivid and natural. It is best to set The functions available on the monitor may vary depending on the model. Refer to the actual product. 4.5.1 Configuring Response Time Press [ ] on the product.
Page 43
Screen Setup Press [ ] to move to appear. Normal: Select this mode when there is no contrast ratio degradation. Low: Select this mode to reduce the black level and increase the white level when there is a contrast ratio degradation. Press [ ] to move to the option you want and press the [ The selected option will be applied.
Configuring Tint Adjust the tint of the screen. This option is not available when Dynamic Contrast Adjust the value of the color red in the picture. (Range: 0~100) A higher value will increase the intensity of the color. This option is not available when 5.1.1 Configuring Red Press [ ] on the product.
Configuring Tint Press [ ] to move to Adjust the Green using the [ Blue Adjust the value of the color blue in the picture. (Range: 0~100) A higher value will increase the intensity of the color. This option is not available when 5.3.1 Configuring Blue Press [ ] on the product.
Configuring Tint This option is not available when This option is not available when 5.4.1 Configuring the Color Tone Settings Press [ ] on the product. Press [ ] to move to Press [ ] to move to mode Cool 2: Set the color temperature to be cooler than Cool 1: Set the color temperature to be cooler than...
Configuring Tint Gamma Adjust the mid-range brightness (Gamma) of the picture. This option is not available when 5.5.1 Configuring Gamma Press [ ] on the product. Press [ ] to move to Press [ ] to move to Press [ ] to move to the option you want and press the [ The selected option will be applied.
Resizing or Relocating the Screen Size Change the picture size. 6.1.1 Changing the Image Size Press [ ] on the product. Press [ ] to move to Press [ ] to move to mode Auto: Display the picture according to the aspect ratio of the input source. Wide: Display the picture in full screen regardless of the aspect ratio of the input source.
Resizing or Relocating the Screen H-Position Move the screen to the left or right. Available only when 6.2.1 Configuring H-Position Press [ ] on the product. Press [ ] to move to Press [ ] to move to Adjust the H-Position V-Position Move the screen up or down.
Resizing or Relocating the Screen Press [ ] to move to Adjust the V-Position Menu H-Position Move the menu position to the left or right. 6.4.1 Configuring Menu H-Position Press [ ] on the product. Press [ ] to move to Press [ ] to move to appear.
Resizing or Relocating the Screen 6.5.1 Configuring Menu V-Position Press [ ] on the product. Press [ ] to move to Press [ ] to move to appear. Adjust the Menu V-Position SIZE&POSITION and press [ ] on the product. Menu V-Position and press [ ] on the product.
Setup and Reset Adjust the power consumption of the product to save energy. 7.1.1 Eco Motion Sensor Eco Motion Sensor specified area for a specified period of time. Configuring the Eco Motion Sensor Press [ ] on the product. Press [ ] to move to Press [ ] to move to...
Setup and Reset Configuring Backlight Press [ ] on the product. Press [ ] to move to Press [ ] to move to Press [ ] to move to Off: Turn off the screen and activate DPMS mode. If the monitor to detect movement and turn on after it turned off. Dimming: Reduce the brightness of the screen (still turned on).
Page 54
Setup and Reset Press [ ] to move to will appear. On: The Eco sensor detects the ambient illumination and automatically controls the brightness. Press [ ] to move to the option you want and press the [ The selected option will be applied. Configuring Sensitivity Press [ ] on the product.
Setup and Reset Press [ ] to move to Press [ ] to move to The following screen will appear. Brighter: Increase the current brightness of the screen. Current: Maintain the current brightness of the screen. Dimmer: Decrease the current brightness of the screen. Press [ ] to move to the option you want and press the [ The selected option will be applied.
Setup and Reset The selected option will be applied. This option is not available when This option is not available when 7.1.4 Eco Icon Display Configuring the Eco Icon Display Settings Press [ ] on the product. Press [ ] to move to Press [ ] to move to Press [...
Page 57
Setup and Reset When the screen becomes brighter as the ambient light becomes brighter and the Sensor activates, the brightness slide bar level will increase with a sun image displayed above the bar. When the screen becomes darker, the brightness slide bar level will decrease with a moon image displayed above the bar.
Setup and Reset The progress of a tree growing will be represented as 10 different images (stages). After one full-grown tree is complete, the initial image will be restored and the number of trees will continue to accumulate. The number for energy trees will be rounded to one decimal place. Menu Transparency Set the transparency for the menu windows: 7.2.1 Changing Menu Transparency...
Setup and Reset Press [ ] to move to Press [ ] to move to the option you want and press the [ The selected option will be applied. PC/AV Mode PC/AV Mode to AV. The picture size will be enlarged. This option is useful when you view a movie. 7.4.1 Configuring PC/AV Mode Settings Press [ ] on the product.
Setup and Reset Auto Source Activate Auto Source. 7.5.1 Configuring Auto Source Press [ ] on the product. Press [ ] to move to Press [ ] to move to appear. Auto: The input source is automatically recognized. Manual: Manually select an input source. Press [ ] to move to the option you want and press the [ The selected option will be applied.
Setup and Reset Press [ ] to move to appear. Press [ ] to move to the option you want and press the [ The selected option will be applied. Key Repeat Time Control the response rate of a button when the button is pressed. 7.7.1 Configuring Key Repeat Time Press [ ] on the product.
Setup and Reset Customized Key By configuring Customized Key conveniently. 7.8.1 Configuring Customized Key Press [ ] on the product. Press [ ] to move to Press [ ] to move to appear. Can be set to 3D, Press [ ] to move to the option you want and press the [ The selected option will be applied.
Setup and Reset Press [ ] to move to appear. Off: Deactivate the off timer so that the product does not power off automatically. On: Activate the off timer so that the product powers off automatically. Press [ ] to move to the option you want and press the [ The selected option will be applied.
Setup and Reset you do not want the timer to activate, go to to Off. 7.11 Reset Return all the settings for the product to the default factory settings. 7.11.1 Initializing Settings (Reset) Press [ ] on the product. Press [ ] to move to Press [ ] to move to...
INFORMATION Menu and Others INFORMATION View the current input source, frequency and resolution. 8.1.1 Displaying INFORMATION Press [ ] on the product. Press [ ] to move to INFORMATION. The current input source, frequency and resolution will appear. Configuring Brightness in the Startup Screen Adjust Brightness using the [...
Page 66
INFORMATION Menu and Others Press [ ] in the startup screen. The following screen will appear. Adjust the Volume using the [ Volume Exit Adjust Enter ] button. 8 INFORMATION Menu and Others...
Requirements Before Contacting Samsung Customer Service Center 9.1.1 Testing the Product Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check if your product is operating normally by using the product test function.
Page 68
Troubleshooting Guide "Not Optimum Mode" is displayed. The images on the screen look distorted. The screen is not clear. The screen is blurry. The screen appears unstable and shaky. There are shadows or ghost images left on the screen. The screen is too bright. The screen is too dark. Screen color is inconsistent.
Page 69
Troubleshooting Guide The volume is too low. A beeping sound is heard when my PC is booting. If a beeping sound is heard when your PC is Sound issue Adjust the volume. If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software program.
Page 70
Troubleshooting Guide Q & A Question How can I change the frequency? Answer Set the frequency on your graphics card. Windows XP: Select Control Panel Themes Display Settings → → and adjust Refresh rate under Monitor settings. Windows ME/2000: Select Control Panel Settings Advanced Monitor, and adjust Refresh rate...
Page 71
Troubleshooting Guide Question How can I change the resolution? How do I set power-saving mode? Refer to the user manual for your PC or graphics card for further instructions on adjustment. Answer Windows XP: Go to Control Panel → Themes Display Settings and adjust the resolution.
Specifications 10.1 General Model Name Panel Size Display area Synchroni Horizontal zation Frequency Vertical Frequency Display Color Resolution Optimum resolution Maximum resolution Maximum Pixel Clock Power Supply Signal connectors Dimensions (W x H x D) / Weight Environme Operating ntal considerat Storage ions...
Hereby, Samsung Electronics, declares that this [MONITOR] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The official Declaration of Conformity may be found at http://www.samsung.com, go to Support > Search Product Support and enter the model name.
Page 74
Specifications The displayed power consumption level can vary in different operating conditions or when settings are changed. To reduce the power consumption to 0 watts, turn off the power switch on the back of the product or disconnect the power cable. Be sure to disconnect the power cable when you will not be using the product for an extended period of time.
Specifications 10.3 Standard Signal Mode Table This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Therefore, a resolution other than the specified resolution may degrade the picture quality.
Page 76
Specifications HDMI Resolution 1920 x 1080 60HZ 640 x 480 60Hz,480p 720 x 480 60Hz,480p 720 x 576 50Hz, 576p 1280 x 720 50Hz,720p 1280 x 720 Normal 60Hz,720p 1920 x 1080 50Hz,1080i 1920 x 1080 60Hz,1080i 1920 x 1080 24Hz,1080p 1920 x 1080 50Hz,1080p...
Page 77
Specifications Resolution 1920 x 1080,1080p 24Hz, FramePacking 1280 x 720,720p 50Hz, FramePacking 1280 x 720,720p 60Hz, FramePacking 1920 x 1080,1080i 50Hz,SBS(Half) 1920 x 1080,1080i 60Hz,SBS(Half) 1920 x 1080,1080p 50Hz,SBS(Half) 1920 x 1080,1080p 60Hz,SBS(Half) 1280 x 720,720p 50Hz,TNB 1280 x 720,720p 60Hz,TNB 1920 x 1080,1080p...
Page 78
Specifications Vertical Frequency Repeating the same picture dozens of times per second allows you to view natural pictures. The repeat frequency is called "vertical frequency" or "refresh rate" and is indicated in Hz. 10 Specifications...
Appendix Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. U.S.A CANADA MEXICO ARGENTINA BRAZIL BOLIVIA CHILE COLOMBIA COSTA RICA DOMINICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA...
Page 84
Appendix Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
Page 85
Appendix Terminology OSD(On Screen Display) On screen display (OSD) allows you to configure on-screen settings to optimize the picture quality as required. It allows you to change the screen brightness, tint, size and many other settings using menus displayed on the screen. Gamma The Gamma menu adjusts the grey scale that represents middle tones on the screen.
Page 86
Appendix Resolution Resolution is the number of horizontal pixels and vertical pixels that form a screen. It represents the level of display detail. A higher resolution displays a greater amount of information on the screen and is suitable for performing multiple tasks at the same time. E.g.
Page 87
Checking the Resolution and Frequency Cleaning Connecting Headphones Connecting to a PC Connecting to a Video Device Connection Using the HDMI Cable Contact SAMSUNG WORLDWIDE Copyright Correct Disposal of This Product Correct posture to use the product Customized Key Driver Installation...
Page 88
Index Testing the Product Tidying Up the Connected Cables Volume Index...