Mitsubishi Electric FR-A800 Series Beginner's Manual page 84

Parameter list (FR-A800)
Param-
Name
eter
Torque control P gain 1
824 (current loop
proportional gain)
Torque control integral
825 time 1 (current loop
integral time)
826 Torque setting filter 1
827 Torque detection filter 1
828 Model speed control gain
830 Speed control P gain 2
Speed control integral
831
time 2
832 Speed setting filter 2
833 Speed detection filter 2
834 Torque control P gain 2
Torque control integral
835
time 2
836 Torque setting filter 2
837 Torque detection filter 2
840 Torque bias selection
841 Torque bias 1
842 Torque bias 2
843 Torque bias 3
844 Torque bias filter
Torque bias operation
845
time
Torque bias balance
846
compensation
Fall-time torque bias
847
terminal 1 bias
Fall-time torque bias
848
terminal 1 gain
Analog input offset
849
adjustment
850 Brake operation selection
853 Speed deviation time
854 Excitation ratio
Terminal 4 function
858
assignment
Torque current/Rated PM
859
motor current
Second motor torque
860 current/Rated PM motor
current
864 Torque detection
865 Low speed detection
A - 12
Setting Range Initial Value
0–500 % 100 %
0–500 ms 5 ms
0–5 s, 9999 9999
0–0.1 s 0 s
0–1000 % 60 %
0–1000 %,9999 9999
0–20 s, 9999 9999
0–5 s, 9999 9999
0–0.1 s, 9999 9999
0–500 %, 9999 9999
0–500 ms, 9999 9999
0–5 s, 9999 9999
0–0.1 s, 9999 9999
0–3, 24, 25, 9999 9999
600–1400 %,
9999
9999
600–1400 %,
9999
9999
600–1400 %,
9999
9999
0–5 s, 9999 9999
0–5 s, 9999 9999
0–10 V, 9999 9999
0–400 %, 9999 9999
0–400 %, 9999 9999
0–200 % 100 %
0–2 0
0–100 s 1 s
0–100 % 100 %
0, 1, 4, 9999 0
0–500 A, 9999
0–3600 A, 9999
9999
0–500 A, 9999
0–3600 A, 9999
9999
0–400 % 150 %
0–590 Hz 1.5 Hz
Param-
Name
eter
Torque monitoring
866
reference
867 AM output filter
Terminal 1 function
868
assignment
869 Current output filter
Speed detection
870
hysteresis
Input phase loss
872
protection selection
873 Speed limit
874 OLT level setting
875 Fault definition
Speed feed forward
877 control/model adaptive
speed control selection
878 Speed feed forward filter
Speed feed forward
879
torque limit
880 Load inertia ratio
881 Speed feed forward gain
Regeneration avoidance
882
operation selection
Regeneration avoidance
883
operation level
Regeneration avoidance
884 at deceleration detection
sensitivity
Regeneration avoidance
885 compensation frequency
limit value
Regeneration avoidance
886
voltage gain
888 Free parameter 1
889 Free parameter 2
Cumulative power
891 monitor digit shifted
times
892 Load factor
Energy saving monitor
893 reference (motor
capacity)
Control selection during
894 commercial power-
supply operation
Power saving rate
895
reference value
896 Power unit cost
Power saving monitor
897
average time
Power saving cumulative
898
monitor clear
Operation time rate
899
(estimated value)
FM/CA terminal
C0
(900)
calibration
C1
AM terminal calibration
(901)
Appendix
Setting Range Initial Value
0–400 % 150 %
0–5 s 0.01 s
0–6, 9999 0
0–5 s 0.02 s
0–5 Hz 0 Hz
0, 1 0
0–400 Hz 20 Hz
0–400 % 150 %
0, 1 0
0–2 0
0–1 s 0 s
0–400 % 150 %
0–200 times 7 times
0–1000 % 0 %
0–2 0
380 V DC/
300–800 V
760 V DC
0–5 0
0–590 Hz, 9999 6 Hz
0–200 % 100 %
0–9999 9999
0–9999 9999
0–4, 9999 9999
30–150 % 100 %
Rated
0.1–55 kW /
inverter
0–3600 kW
capacity
0–3 0
0, 1, 9999 9999
0–500, 9999 9999
0, 1–1000 h, 9999 9999
0, 1, 10, 9999 9999
0–100 %, 9999 9999
— —
— —