Page 1 Contact-Type Digital Displacement Sensor HG-S Series User's Manual WUME-HGS-2 2016.5 panasonic.net/id/pidsx/global SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 2 (MEMO) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 3 Thank you for purchasing an contact-type digital displacement sensor HG-S series. Before using this product, read and understand this User's Manual. Use the product correctly and in the optimum manner. Keep this manual in a safe location for reference whenever necessary.
Page 4: Table Of Contents
4-2-2 Presets ··············································································· 4-8 4-2-3 Teaching Mode ····································································· 4-11 4-2-3-1 HIGH Set Value Fine Adjustment Function and LOW Set Value Fine Adjustment Function ··················· 4-18 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 5 5-3-9-1 Pressure Check / Pressure Check Set Value / Alarm Delay Count ················································· 5-59 5-3-9-2 Catch Check ························································· 5-63 5-3-9-3 Number of Connected Controllers Check (Master Unit Only) · 5-65 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 6 ·············································· 7-3 Replacing the Rubber Bellows ······························································· 7-4 Error Messages ······························································· 7-5 Troubleshooting © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 7: Chapter 1 Introduction
Chapter 1 INTRODUCTION 1-1 Safety Cautions ········································································ 1-2 1-2 Safety Information ····································································· 1-2 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 8: Safety Cautions
Risk of short-circuiting and damage to the controller or power supply if in- correctly mounted or connected. ● The controller HG-SC series is designed to be used with the special sensor head HG-S series. If used with other than the special sensor head option, the specifications will not be met and product malfunctioning or damage may occur.
Page 9 ● Never attempt to disassemble, repair, or modify the product. ● When the product becomes unusable or unneeded, dispose of the product appropriately as industrial waste. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 10 (MEMO) SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 11: Chapter 2 Before Using This Product
Chapter 2 BEFORE USING THIS PRODUCT 2-1 Contents of Package ································································· 2-2 2-2 System Configuration ································································ 2-4 2-3 Description of Parts ··································································· 2-5 2-3-1 Controller············································································· 2-5 2-3-2 Sensor Head ········································································ 2-8 2-3-3 Sensor Head Connection Cable ··············································· 2-8 SEN TRONIC Rugghölzli 2 Tel.
Page 12: Contents Of Package
● Instruction Manual (English / Japa- nese, Chinese / Korean): 2 pcs. ● General Information for Safety, Compliance, and Instructions (23 languages): 1 pc. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 13 Rubber bellows (Option) TR-G20×5 ● Bellows: 1 pc. TR-J104 / Length 25mm type ● Joint: 1 pc. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 14: System Configuration
BEFORE USING THIS PRODUCT 2-2 System Configuration The HG-S series consists of controllers, sensor head connection cables, and sensor heads. For the controllers, master units (2 types) and slave units (5 types) are available. Up to 15 slave units can be connected per master unit. (When communication unit consolidated: up to 14 slave units) For the sensor heads, 4 types are available.
Page 15: Description Of Parts
4 Male connector For connection to a master unit or slave unit. Digital display / operation Keep closed when not using. cover © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 16 15 Status mark HOLD (White) Lights up while the judgment value is held. CALC (White) Lights up when set to calculation mode with a slave unit connected. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 17 When short-pressed in the base screen, the preset function turns ON. 19 Preset key When long-pressed for 2 seconds in the base screen, the preset function turns OFF. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 18: Sensor Head
Connects to the sensor head cable connector on the sensor head. 2 Controller connector Connects to the sensor head cable connector on the controller. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 19: Chapter 3 Installation And Connections
Chapter 3 INSTALLATION AND CONNECTIONS 3-1 Mounting the Controller ······························································ 3-2 3-1-1 Mounting on a DIN Rail ·························································· 3-2 3-1-2 Removing from a DIN Rail ······················································· 3-2 3-2 Attaching the Sensor Head ························································· 3-3 3-3 Wiring the Controller Connector on the Sensor Head Connection Cable 3-5 3-3-1 Disassembly Procedure ··························································...
Page 20: Mounting The Controller
DIN rail. 3-1-2 Removing from a DIN Rail Grasp the product and push forward. Lift the front to remove. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 21: Attaching The Sensor Head
Tighten to a torque of 12.5N·m or less. Sensor head fastening wrench (accessory) Wrench When tightening the mounting nut, take care not to damage the rubber bellows. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 22 If the rubber bellows is deformed, rotate the bellows to restore to the normal shape. If the rubber bellows is deformed, a load will occur when the spindle operates and damage may result. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 23: Wiring The Controller Connector On The Sensor Head Connection Cable
(white) on the operation unit until the lever locks. Flat-head screwdriver Lever (white) Tip width 2mm or less © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 24 Pull on the wire gently to ensure that it does not come out. Slide the protective cover in the direction of the arrow to return the cover to its original position. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2...
Page 25: Connecting The Controller And Sensor Head
Turn the fastening ring on the sensor head connector in the direction shown to fasten the ring. Do not turn the connector on the L-shaped connector CN-HS-C□L. Risk of damage. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 26: Removing The Sensor Head And Sensor Head Connection Cable
Risk of damage if you pull the cable with excessive force (15N or more) with the fastening ring tightened. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 27: Attaching The Controller And Sensor Head Connection Cable
Pull out If you attempt to disconnect the cable by pulling it without pressing the lock release lever, cable wire breakage and connector damage may occur. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 28: Connecting Controllers
Mount each slave unit one at a time on the DIN rail. Remove all connector covers except for the cover on the end slave unit. Slave unit Slide 3-10 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 29: Removal Method
Loosen the screws on the end plates Remove the end plates. Slide and remove the controllers, one at a time. Slide © Panasonic Industrial Devices SUNX Co., Ltd. 2016 3-11 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 30: Connection Diagrams And I/O Circuit Diagrams
The HG-SC111 and HG-SC111-P cables do not have +V or 0V. Power is supplied from the con- nector of the master unit. 3-12 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 31 (Pink / Violet) External input 3 <Reference> The HG-SC112 and HG-SC112-P cables do not have +V or 0V. Power is supplied from the con- nector of the master unit. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 3-13 SEN TRONIC Rugghölzli 2 Tel.
Page 32: I/O Circuit Diagrams
All outputs are equipped with short-circuit protection. If any one of outputs 1 to 3 short-circuits, all outputs temporarily turn OFF. The outputs automatically recover when the short-circuit state is cleared. 3-14 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 33 All outlets are equipped with short-circuit protection. If any one of outputs 1 to 3 short-circuits, all outputs temporarily turn OFF. The outputs automatically recover when the short-circuit state is cleared. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 3-15 SEN TRONIC Rugghölzli 2...
Page 34 ● The HG-SC111 cable does not have +V or 0V. Power is supplied from the connector of the mas- ter unit. 3-16 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 35 OFF. The outputs automatically recover when the short-circuit state is cleared. ● The HG-SC111-P cable does not have +V or 0V. Power is supplied from the connector of the master unit. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 3-17 SEN TRONIC Rugghölzli 2 Tel.
Page 36 ● The HG-SC112 cable does not have +V or 0V. Power is supplied from the connector of the mas- ter unit. 3-18 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 37 OFF. The outputs automatically recover when the short-circuit state is cleared. ● The HG-SC112-P cable does not have +V or 0V. Power is supplied from the connector of the master unit. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 3-19 SEN TRONIC Rugghölzli 2 Tel.
Page 38 (MEMO) SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 39: Chapter 4 Basic Operation
Chapter 4 BASIC OPERATION 4-1 Explanation of Basic Operation ···················································· 4-2 4-1-1 From Power ON to Mode Selection ··········································· 4-2 4-1-2 Operation Keys and Display ···················································· 4-3 4-1-2-1 Operation Keys ······················································ 4-3 4-1-2-2 Display ································································ 4-4 4-2 Explanation of Modes ······························································· 4-5 4-2-1 Display Switching Mode ··························································...
Page 40: Explanation Of Basic Operation
Short press Presets (refer to page 4-8) You can perform zero-point adjustment, and shift to any preset value. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 41: Operation Keys And Display
● Change set values. ENTER key ● Finalize setting items and settings. EXIT key ● Cancel setting items and settings. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 42: Display
2 seconds. ● The number of setting items in the level lights up, and the or- der of the setting times is shown by blinking. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 43: Explanation Of Modes
ON / OFF based on the LOW set value and the HIGH set value. Analog output is also output based on the judgment value. For the data flow, refer to “5-1-2 Data Flow”. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 44 Press the ENTER key to finalize the setting and return to the base screen. If you press the ENTER key with "LABEL" selected, you will move to the label setting screen. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 45 Press the UP / DOWN key to change the alphanumeric character. Press the LEFT / RIGHT key to change the digit position. Press the ENTER key to finalize the setting and return to the base screen. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 46: Presets
When the preset function turns ON, the preset indicator (green) lights up. If the preset value is set to "0.0000" (default setting), you can perform zero-point adjustment. Preset indicator (green) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 47 When the upper or lower display limit is exceeded MAIN (white) When an alarm is output SUB (green) When an error is output © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 48 BASIC OPERATION <Canceling a preset> To cancel the preset function, long-press the preset key for 2 seconds. Preset indicator (green) 4-10 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 49: Teaching Mode
Median value LOW set value Lowest value <Reference> To change teaching type, refer to “5-2-4 Teaching Types ( )”. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 4-11 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 50 When teaching is completed, "GOOD" appears in the digital display / MAIN (white), and the HIGH set value and LOW set value are finalized. You then return automatically to the base screen. 4-12 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 51 When the upper or lower display limit is exceeded MAIN (white) During alarm output SUB (green) When an error is output © Panasonic Industrial Devices SUNX Co., Ltd. 2016 4-13 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 52 Measure the first workpiece, and press the ENTER key. "SET.2" appears in the digital display / SUB (green). Measure the second workpiece, and press the ENTER key. 4-14 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 53 The higher judgment value is set as the HIGH set value and the lower judgment value is set as the LOW set value, regardless of the order of steps and 4. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 4-15 SEN TRONIC Rugghölzli 2...
Page 54 Measure the good workpiece, and press the ENTER key. "SET.3" appears in the digital display / SUB (green). Measure the LOW-side defective workpiece, and press the ENTER key. 4-16 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 55 The value between the highest value and the median value is set as the HIGH set value, and the value between the lowest value and the median value is set as the LOW set value. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 4-17 SEN TRONIC Rugghölzli 2...
Page 56: High Set Value Fine Adjustment Function And Low Set Value Fine Adjustment Function
If you take no action for 5 seconds, the screen will automatically return to the base screen and the setting will be finalized. 4-18 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 57 Press the ENTER key to finalize the setting. <Reference> If you take no action for 5 seconds, the screen will automatically return to the base screen and the setting will be finalized. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 4-19 SEN TRONIC Rugghölzli 2 Tel.
Page 58: Bank Mode
Save to bank Key operation Load from bank External input Load from bank 4-20 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 59: Saving And Loading By Operation Key
Press the DOWN key. "BANK1" appears in the digital display / SUB (green), and "YES" ap- pears in the digital display / MAIN (white). Press the LEFT / RIGHT key to change banks. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 4-21 SEN TRONIC Rugghölzli 2...
Page 60 If you selected "LOAD" in step 3, the settings saved in the bank are loaded. Press the EXIT key twice to return to the base screen. 4-22 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 61: Loading By External Input
<Reference> For the procedure for setting external input to bank A input or bank B input, refer to “5-3-3 Exter- nal Input ( )”. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 4-23 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 62: Key Lock
● When any key is pressed, "LOCK" appears in the digital display / SUB (green), and "ACT" ap- pears in the digital display / MAIN (white). ● Functions that use external input are enabled. 4-24 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 63 Simultaneously hold down the ENTER key and EXIT key. The digital display / SUB (green) and the digital display / MAIN (white) change as shown below. When "OFF" appears in the digital display / MAIN (white), release the keys. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 4-25 SEN TRONIC Rugghölzli 2...
Page 64 (MEMO) 4-26 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 65: Chapter 5 Function Settings
Chapter 5 FUNCTION SETTINGS 5-1 Overview of Setting Menu ········· 5-2 5-3-7 Scaling Upper Limit Value / Scaling Lower Limit Value ( ) ····5-54 5-1-1 Menu Structure ····················5-2 5-3-8 Eco Mode ( ) ···················5-57 5-1-2 Data Flow ···························5-4 5-1-3 Setting Items and Default Values ·5-5 5-3-9 Alarm Setting ( ) ··········5-58 5-3-9-1 Pressure Check / Pressure Check Set...
Page 66: Overview Of Setting Menu
(Master unit only) [HIGH set value] [LOW set value] [Hysteresis] [Teaching type] [Tolerance] © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 67 [Preset save] Measurement [Lever ratio] [Response time] [Output operation] selection direction © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 68: Data Flow
*1 When a calculation mode is selected: The number of slave units used in the calculation var- ies depending on the calculation application selection. *2 Only appears during calculation. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 69: Setting Items And Default Values
You can select the judgment output operation. Output operation (OUTPUT) N.O. (normal open) / N.C. (normal closed) 5-24 <Default value: N.O.> © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 70 Eco mode (ECO) display turn OFF when idle. 5-57 OFF (Eco OFF) / ON (Eco ON) <Default value: OFF> © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 71 MAINTE tion log MAX. REC Over stroke log OVR. NUM © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 72: Basic Settings
[Preset data selection] [Preset save] [Measurement direction] [Lever ratio] [Response time] [Output operation] © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 73: High Set Value
Setting item Setting range Default value HIGH set value (HI.SET) -199.9999 to 199.9999 (mm) 5.0000 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 74: Low Set Value
Setting range Default value LOW set value (LO.SET) -199.9999 to 199.9999 (mm) 1.0000 5-10 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 75: Hysteresis
HIGH set value Hysteresis Hysteresis LOW set value Stable Judgment value HIGH © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-11 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 76 Setting range Default value Hysteresis (HYSTER) 0 to 199.9999 (mm) 0.0030 5-12 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 77: Teaching Types
HIGH set value Median value LOW set value Lowest value <Reference> For teaching type, refer to “4-2-3 Teaching Mode”. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-13 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 78 1-point teaching (TCH.1) Teaching type (TEACH) 2-point teaching (TCH.2) TCH.1 3-point teaching (TCH.3) 5-14 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 79 Finalize Setting Setting range Default value Tolerance (±) (TOL<±>) 0 to 199.9999 0.1000 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-15 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 80: Preset Value
Setting range Default value Preset value (PR. VAL) -199.9999 to 199.9999 (mm) 0.0000 5-16 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 81: Preset Data Selection ( ) ·5-17
Set values Default value Normal measured value (NORM.V) Preset data selection (PR.OBJ) NORM.V Judgment value (JUDGE.V) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-17 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 82: Preset Save
Set values Default value Preset save OFF (OFF) Preset save (PR.SAVE) Preset save ON (ON) 5-18 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 83: Measurement Direction
If you change the measurement direction setting, you must also change the settings below. • HIGH set value • LOW set value • Self trigger edge direction in the hold setting © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-19 SEN TRONIC Rugghölzli 2 Tel.
Page 84 Default value Normal display (plus direction ) (NORMAL) Measurement direction (DIRECT) NORMAL Reverse display (minus direction) (REVERS) 5-20 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 85: Lever Ratio
" will appear in the digital display / MAIN (white). You will then return to the lever ratio setting screen. Set a valid value for the lever ratio. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-21 SEN TRONIC Rugghölzli 2 Tel.
Page 86: Response Time
● If the response time is "3" (3ms), the indeterminate value display will show “ ” for 1ms. 5-22 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 87 3ms (3) 5ms (5) 10ms (10) Response time (SPEED) 100ms (100) 500ms (500) 1,000ms (1000) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-23 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 88: Output Operation
Default value Normal Open (N.O.) Output operation (N.O. / N.C.) N.O. Normal Closed (N.C.) 5-24 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 89: Advanced Settings
(Master unit only) [Number of digits displayed] [Analog scaling] [Scaling upper limit value] [Scaling lower limit value] [Eco mode] [Alarm setting] © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-25 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 90: Hold Setting
● Depending on the calculation application selection setting, the hold setting on the slave unit used for calculation may be invalid. 5-26 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 91: Sample Hold
2. If the reset input turns ON while the external trigger input is ON, the indeterminate state is held. 3. Judgment output outputs the judgment result based on the output setting. *When the calculation function is used, the calculation value is “CALC”. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-27 SEN TRONIC Rugghölzli 2...
Page 92: Peak To Peak Hold / 2
Default value Hold (HOLD) Trigger mode (TRG) HOLD One-shot (1SHOT) 5-28 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 93 Long-press for 2 seconds CALC: Only appears on master unit ALL IN: Only appears on master unit : Select : Finalize © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-29 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 94: Peak Hold, Bottom Hold, Peak To Peak Hold, Peak To Peak Hold / 2 ·5-30 5-3-1-1-3 Ng Hold
4. Judgment output outputs the judgment result based on the output setting. *When the calculation function is used, the calculation value is “CALC”. 5-30 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 95 The judgment value (JUDGE.V) is held in the same way in the respective measurement modes of Bottom hold, Peak to peak hold, and Peak to peak hold / 2. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-31 SEN TRONIC Rugghölzli 2...
Page 96 Status mark - : Select HOLD (white) : Finalize light up 5-32 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 97: Ng Hold
● Once a HIGH judgment is output during one output judgment interval, a LOW judgment is not output. Once a LOW judgment is output, a HIGH judgment is not output. ● The trigger mode setting is invalid for NG hold. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-33 SEN TRONIC Rugghölzli 2 Tel.
Page 98 : Select : Finalize Status mark - HOLD (white) light up 5-34 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 99: Self Sample Hold (Delay Timer)
5. If the reset input turns ON, the indeterminate state is held. If this occurs during the delay time, the delay time ends. 6. Judgment output outputs the judgment result based on the output setting. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-35 SEN TRONIC Rugghölzli 2...
Page 100 Set values / setting range Default value Delay timer (DLY.TIM) 0 to 9999 (ms) 1000 5-36 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 101 : Select : Move through digits Status mark - TRIG (white) and : Change value HOLD (white) light up : Finalize © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-37 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 102: Self Sample Hold (Static Width)
5. If the reset input turns ON, the indeterminate state is held. If within the sampling interval, the sampling interval ends. 6. Judgment output outputs the judgment result based on the output setting. 5-38 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 103 Setting item Set values / setting range Default value Static width (DLY.WD) 0 to 199.9999 (mm) 0.01 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-39 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 104 : Move through digits Status mark - TRIG (white) and : Change value HOLD (white) light up : Finalize 5-40 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 105: Self Peak Hold / Self Bottom Hold
3. If the reset input turns ON, the indeterminate state is held. If within the sampling interval, the sampling interval ends. 4. Judgment output outputs the judgment result based on the output setting. *When the calculation function is used, the calculation value is “CALC”. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-41 SEN TRONIC Rugghölzli 2 Tel.
Page 106 4. If the reset input turns ON, the indeterminate state is held. If within the sampling interval, the sampling interval ends. 5. Judgment output outputs the judgment result based on the output setting. 5-42 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 107 Setting item Set values / setting range Default value Rise (UP) Self trigger edge direction (SLF.EDG) Fall (DOWN) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-43 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 108 : Move through digits : Change value : Finalize : Select : Finalize 5-44 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 109: (Master Unit Only)
<Reference> Input All can only be set on a master unit to which slave units are connected. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-45 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 110 Set values Default value Single (ONE) Input all (ALL IN) All (ALL) 5-46 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 111: External Input
<Reference> ● For controller I/O circuit diagrams, refer to “3-6-2 I/O Circuit Diagrams”. ● For input all, refer to “5-3-2 Input All ( ) (Master Unit Only)”. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-47 SEN TRONIC Rugghölzli 2 Tel.
Page 112 External input (EXT.IN) P/R/T Bank A / Bank B / Reset (BANK/R) Bank A / Bank B / Trigger (BANK/T) 5-48 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 113: External Output
● For the output operation settings, refer to “5-2-12 Output Operation ( )”. ● For the alarm function, refer to “5-3-9 Alarm Setting ( )”. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-49 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 114 2-value (2 VAL) External output (EXT.OUT) 3 VAL Logic (LOGIC) Logic 2 (LOGIC2) 5-50 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 115: Number Of Digits Displayed
(NORM.V), LOW set value, HIGH set value, sensor head measured values, calculated values, and judgment values (JUDGE.V). ● Changes to the number of digits displayed setting do not affect judgment output. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-51 SEN TRONIC Rugghölzli 2...
Page 116: Analog Scaling
Error output Linearity ±0.25% F.S. Maximum load impedance 250Ω max. 5-52 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 117 Setting item Set values Default value Default (DEFALT) Analog scaling (ANALOG) DEFALT Free (FREE) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-53 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 118: Scaling Upper Limit Value / Scaling Lower Limit Value
Outputs 4mA. 20mA Judgment value (JUDGE.V) Lower limit value = Upper limit value (5mm) 5-54 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 119 Setting item Setting range Default value Scaling upper limit value (ANA.HI) -199.9999 to 199.9999 (mm) 10.0000 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-55 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 120 Setting range Default value Scaling lower limit value (ANA.LO) -199.9999 to 199.9999 (mm) 0.0000 5-56 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 121: Eco Mode
: Finalize Setting item Set values Default value Eco OFF (OFF) Eco mode (ECO) Eco ON (ON) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-57 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 122: Alarm Setting
You can turn catch check ON / OFF. Number of connected control- You can turn the number of connected controllers check ON / OFF. lers check 5-58 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 123: Pressure Check / Pressure Check Set Value
Alarm not output because recovered Alarm delay count within alarm delay count Outputs HI / GO / LO according to the output setting. Alarm © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-59 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 124: Alarm Delay Count
Setting range Default value Alarm delay count (DELAY) 1 to 1000 1000 5-60 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 125: Pressure Check / Pressure Check Set
: Finalize Setting item Set values Default value Check ON (ON) Pressure check (PRS.CHK) Check OFF (OFF) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-61 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 126 Setting range Default value Pressure check set value (PRS.SET) -199.9999 to 199.9999 (mm) 10.0000 5-62 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 127: Catch Check
This function can only be used when the measurement mode is set to a mode that has external trigger input enabled in “5-3-1 Hold Setting ( )”. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-63 SEN TRONIC Rugghölzli 2 Tel.
Page 128 Set values Default value Check OFF (OFF) Catch check (CAT.CHK) Check ON (ON) 5-64 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 129: Number Of Connected Controllers Check (Master Unit Only)
(CON.CHK) Check ON (ON) <Reference> The number of connected controllers check can only be turned ON at the master unit. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-65 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 130: Calculation Settings ( ) (Master Unit Only)
If a slave unit is not connected, "Calculation Mode" and "Calculation Application Selection" will not appear. ● The calculation setting menu only appears on the master unit. 5-66 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 131: Calculation Mode
Setting item Set values Default value No calculation (NO.CALC) Calculation mode (MODE) NO.CALC Calculate (CALC) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-67 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 132: Calculation Application Selection
"CURVEA" (curvature), or "THICK" (thickness) is selected, the specified number of slave units closest to the master unit will be used for calculation. Slave units other than those units will not be used. 5-68 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 133: Maximum Value
• The judgment value (JUDGE.V) (calculation result) appears on the digital display / MAIN (white) of the master unit. The normal measured value (NORM.V) appears on the digital display / MAIN (white) of each slave unit. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-69 SEN TRONIC Rugghölzli 2...
Page 134: Minimum Value
• The response time for judgment output is the response time setting on the master unit and slave units plus 3ms. 5-70 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 135: Average Value
• The hold function cannot be used on the master unit. • The response time for judgment output is the response time setting on the master unit and slave units plus 3ms. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-71 SEN TRONIC Rugghölzli 2...
Page 136: Torsion
3ms. <Reference> This application can only be selected when at least three slave units are connected. 5-72 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 137: Curvature
• The response time for judgment output from the master unit is the response time setting on the master unit and slave units plus 3ms. <Reference> This application can only be selected when at least two slave units are connected. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-73 SEN TRONIC Rugghölzli 2 Tel.
Page 138: Thickness
3ms. <Reference> This application can only be selected when at least one slave unit is connected. 5-74 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 139: Copy Settings
On master unit [Copy select indivisual] [Copy select all] [Copy execution] On slave unit [Copy lock] © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-75 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 140 1 unit <Reference> Only current settings can be copied. Settings stored in a bank are not copied. 5-76 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 141: Copy Select Individual ( ) (Master Unit Only)
● By executing select all, you can copy all settings at once. ● You can use preset keys to select individual settings to be copied / not copied in the basic set- tings (BASIC) and advanced settings (ADVANC). © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-77 SEN TRONIC Rugghölzli 2...
Page 142 Number of digits displayed (DIGIT): YES / NO Eco mode (ECO): YES / NO Alarm setting (ALARM): YES / NO 5-78 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 143: Copy Select All ( ) (Master Unit Only)
Setting item Set values Default value Copy all (YES) Copy select all (CHK.ALL) Do not copy all (NO) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-79 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 144: Copy Execution ( ) (Master Unit Only)
Copying Done Slave unit Slave unit Master unit : Finalize 5-80 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 145: (Slave Units Only)
Done Slave unit (Copy Lock OFF) Slave unit (Copy Lock ON) Master unit : Finalize © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-81 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 146: Bank Settings
● Settings loaded from a bank are saved even if the power is turned OFF. ● For the procedures for saving and loading settings, refer to “4-2-4 Bank Mode”. 5-82 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 147 HIGH set value, LOW set value (THRS) Bank save setting (BNK.DAT) HIGH set value, LOW set value, preset value (THRS.PR) THRS All (ALL) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-83 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 148: Calibration Settings
Correct deviation between detected value and target value. Target point Span Zero point 5-84 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 149 Setting item Set values Default value Default (DEFALT) Calibration selection (CAL.SEL) DEFAUL User settings (USER) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-85 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 150 Adjustment value 2 User settings (USER) -199.9999 to 199.9999 (mm) 10.0000 (AJ.VAL2) 5-86 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 151 When the zero point measured value and target point measured value have been correctly acquired, "GOOD" appears and calibration is executed. Press the EXIT key repeatedly to return to the base screen. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-87 SEN TRONIC Rugghölzli 2...
Page 152: Initialization ( )
For the default value of each setting, refer to “5-1-3 Setting Items and Default Values”. <Reference> ● Executing initialization does not initialize settings stored in a bank. ● Calibration settings are not initialized. 5-88 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 153 FUNCTION SETTINGS Setting method Long-press for 2 seconds CALC: Only appears on master unit Auto Auto © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-89 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 154: Maintenance
Display units are 1m. Over stroke log (OVR.NUM) Shows a log of the number of times the maximum stroke was exceeded. 5-90 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 155 Total stroke operation log (SUM.REC) Maximum peak value (MAX.VAL) Maintenance (MAINTE) ― Maximum peak value operation log (MAX.REC) Over stroke log (OVR.NUM) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 5-91 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 156 (MEMO) 5-92 © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 157: Chapter 6 Specifications
Chapter 6 SPECIFICATIONS 6-1 Specifications ··········································································· 6-2 6-2 Dimensions·············································································· 6-5 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 158 Input 1 / Input 2 / Input 3 can be changed to "Preset / Reset / External input switching Trigger", "Bank Input A / Bank Input B / Select (Preset, Reset, ― Trigger)" © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 159: Specifications
10mA 5) Do not use or store in an environment that has been pressurized to an air pressure higher than the at- mospheric pressure at 0m. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 160 6) Typical value in a clean environment with no contact with dust or liquids such as water and oil. Four million times (typical) when HG-S□R is mounted in upward mount. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2...
Page 161: Dimensions
(58.5) Compatible with 35mm width DIN rail 14.3 R 30mm or more R 30mm or more © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 162 21.5 36.5 (64.8) Compatible with 35mm width DIN rail 14.3 R 30mm or more © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 163 -0.022 M8 (P = 0.5) SR1.59 Note: The HG-S□R low measuring force type is not equipped with rubber bellows. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com...
Page 164 (MEMO) © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 165: Chapter 7 Appendix
Chapter 7 Appendix 7-1 Maintenance and Inspection ························································ 7-2 7-1-1 Maintenance Cautions ···························································· 7-2 7-1-2 Main Inspection Items ···························································· 7-2 7-2 Replacing the Probe ·································································· 7-3 7-3 Replacing the Rubber Bellows ····················································· 7-4 7-4 Error Messages ········································································ 7-6 7-5 Troubleshooting ········································································ 7-7 SEN TRONIC Rugghölzli 2 Tel.
Page 166: Maintenance And Inspection
• Is the supplied power within the rated voltage range (24V DC ±10%)? • Is the ambient operating temperature within the specified range (-10 to +50°C)? • Is the ambient operating humidity within the specified range (35 to 85% RH)? © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 167: Replacing The Probe
Hold the sensor head fastening wrench in place, and turn only the probe. Turn After attaching the probe, wipe the spindle with absolute alcohol to remove any dirt. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 168: Replacing The Rubber Bellows
Fit the new rubber bellows onto the spindle. Insert to the top edge of the spindle as shown below. Insert to top edge © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com...
Page 169 If the rubber bellows is deformed, restore the normal shape by rotating the bellows or otherwise. If the rubber bellows is deformed, a load will occur when the spindle operates and damage may result. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 170: Error Messages
● Check if an excessive force is applied to the controller or the sensor head. ● If the product still does not operate normally after you check the above, consult our technical support center. © Panasonic Industrial Devices SUNX Co., Ltd. 2016 SEN TRONIC Rugghölzli 2 Tel.
Page 171: Troubleshooting
The object to be measured is not within the Check the measurement range of the sensor head you are using. measurement range. When you use the HG-S Series for the first time, or after re- Zero setting has not been performed. placing the sensor head, perform zero-point adjustment.
Page 172 (MEMO) SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 173 Revision History 1st edition, November 30, 2015 2nd edition, May 20, 2016 SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 174 (MEMO) SEN TRONIC Rugghölzli 2 Tel. +41 (0)56 222 38 18 mailbox@sentronic.com CH - 5453 Busslingen Fax +41 (0)56 222 10 12 www.sentronic.com Produkte, Support und Service...
Page 175 3. DISCLAIMERS (1) Panasonic Industrial Devices SUNX’s sole obligation and liability under this warranty is limited to the repair or re- placement, or refund of the purchase price, of a defective Product, at Panasonic Industrial Devices SUNX’s option.

This manual is also suitable for:

Hg-sc101 Hg-sc101-p Hg-sc111 Hg-sc111-p Hg-sc112 Hg-sc112-p ... Show all

Panasonic HG-S Series User Manual

Chapter 1 INTRODUCTION

Chapter 2 BEFORE USING this PRODUCT

Chapter 3 INSTALLATION and CONNECTIONS

Chapter 4 BASIC OPERATION

Chapter 5 FUNCTION SETTINGS

Chapter 6 SPECIFICATIONS

Chapter 7 Appendix

Quick Links

Related Manuals for Panasonic HG-S Series

Summary of Contents for Panasonic HG-S Series

This manual is also suitable for:

Table of Contents