Toro 22979 Setup Instructions

Trailer trx trencher or stx stump grinder

Advertisement

Quick Links

Trailer
TRX Trencher or STX Stump Grinder
Model No. 22979
Model No. 22979HD
Safety
Read and understand the following before using the
trailer.
Before every use:
– Inspect the coupler, ball, and hitch.
– Always use safety chains.
– Verify that all lights are functioning properly.
– Verify that the tires are properly inflated as
recommended on tires.
– Verify that the lug nuts are tight and torqued
properly.
– Verify that that the machine is properly secured.
Know how to properly control your towing
vehicle/trailer combination on the highway under
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
1. Warning—read the Operator's Manual; maximum weight
of 676 kg (1,492 lb).
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
140-1123
Register at www.Toro.com.
all conditions. Remember that the loaded weight
of the trailer increases your braking and stopping
distances.
You are responsible for determining the towing
capacity of your vehicle.
Clean off the machines prior to loading them
onto the trailer. Keep the trailer clean of loose
debris that could fall off during transport, causing a
hazard.
Use proper loading and unloading procedures
and sequences. Read all manuals and follow the
instructions provided.
Inspect the trailer and machine often during
transport.
decal140-1123
Form No. 3432-587 Rev A
Setup Instructions
133-8061
Original Instructions (EN)
All Rights Reserved *3432-587* A
Printed in the USA.
decal133-8061

Advertisement

Table of Contents
loading

Summary of Contents for Toro 22979

  • Page 1 Form No. 3432-587 Rev A Trailer TRX Trencher or STX Stump Grinder Model No. 22979 Model No. 22979HD Setup Instructions Safety all conditions. Remember that the loaded weight of the trailer increases your braking and stopping Read and understand the following before using the distances.
  • Page 2: Installing The Wheels

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Trailer bed Wheel Install the wheels. Lug nuts Tongue Bolt (5/8 x 3 inches) Attach the tongue. Nut (5/8 inch) Mounting strap Jack Install the trailer jack.
  • Page 3: Attaching The Tongue

    Attaching the Tongue Parts needed for this procedure: g008364 Figure 3 Tongue 1. Tongue 3. Wire harness Bolt (5/8 x 3 inches) 2. Opening 4. Wire (secured to harness) Nut (5/8 inch) Using a jack or hoist, raise the front end of the Procedure trailer bed to allow the installation of the tongue (Figure...
  • Page 4 Installing the Trailer Jack (Model 22979) Parts needed for this procedure: Mounting strap g008366 Figure 5 Jack 1. Trailer (underside) 4. Wire harness Bolt 2. Tongue 5. Bolt (5/8 x 3 inches) Locknut 3. Bolt holes Procedure At the front end of the tongue, pull the wire...
  • Page 5 Installing the Ramp Parts needed for this procedure: Chain Ramp Bolt (1/2 x 1-1/2 inches) Nut (1/2 inch) Ramp strap Cotter pin (1-1/4 inch) Procedure Install the retaining chain from the bed of the trailer to the retaining pin (Figure g008369 Figure 9 1.
  • Page 6: Operation

    g008372 Figure 11 g008371 Figure 10 1. Tongue 3. Wiring harness 2. Holster 1. Lynch pin 4. Ramp 2. Post on ramp 5. Post on bed 3. Ramp strap 6. Cotter pin Operation Raise the ramp and use the straps and lynch Operating the Jack pins to secure it in the transport position (Figure...
  • Page 7: Attaching The Trailer

    Attaching the Trailer This trailer uses couplers that require a 2 inch ball for the hitch. Rotate the jack into the vertical position (Figure 14). Raise the trailer to above the ball hitch. Lift the handle on the tongue. Lower the tongue ball socket over the ball hitch (Figure 15).
  • Page 8 Loading the Trencher CAUTION Attempting to load or unload the machine from a trailer that is not securely hitched to a suitable vehicle could cause the trailer to become unstable, and tip causing injury to you or bystanders. Make sure the trailer is securely hitched to a suitable vehicle parked on a level surface g008375 before attempting to load or unload the...
  • Page 9: Maintenance

    DANGER The ramp in the transport position represents a stored energy hazard and if not secured can fall; injuring you or bystanders. Hold the ramp in place when removing straps and use care to lower the ramp carefully to the ground. Remove the pin on the hold down bar and lay the chain and pin on the center of the trailer bed.
  • Page 10 Notes:...
  • Page 11 Notes:...

This manual is also suitable for:

22979hd

Table of Contents