Table of Contents
Advertisement
Quick Links
Ultra Sonic Boom
2013 and After Multi-Pro 5800, 1750 and WM Turf Sprayers
Model No. 41219—Serial No. 314000001 and Up
This attachment maintains consistent distances from the boom nozzles to the ground when
spraying over uneven surfaces and is intended to be used by professional, hired operators in
commercial applications. It is primarily designed for spraying golf course applications, parks,
sports fields, and on commercial grounds. It is designed to only be used in conjunction with
machines designated by the manufacturer.
This product complies with all relevant European directives. For details, please see the
separate product specific Declaration of Conformity (DOC) sheet.
WARNING
CALIFORNIA
Proposition 65 Warning
This product contains a chemical or chemicals
known to the State of California to cause cancer,
birth defects, or reproductive harm.
Use of this product may cause exposure to
chemicals known to the State of California
to cause cancer, birth defects, or other
reproductive harm.
© 2014—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
™
Leveling Kit
Register at www.Toro.com.
Form No. 3385-426 Rev A
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3385-426* A
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Toro Ultra Sonic Boom 41219
Summary of Contents for Toro Ultra Sonic Boom 41219
- Page 1 Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. © 2014—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3385-426* A 8111 Lyndale Avenue South...
-
Page 2: Table Of Contents
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Hinge Angled strap (for an uncovered boom) Angled strap (for a covered boom) Top or bottom strap Assemble the sensor mounting Compression spring hardware. -
Page 3: No Parts Required
Note: The top straps for the uncovered booms also serve as the bottom straps for the covered booms. Preparing the Machine No Parts Required Procedure Position the machine on a level surface, stop the engine, remove the ignition key, and engage the parking brake. CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously... -
Page 4: Hydraulic Manifold Block
3. Install a flat washer on each of the 2 hex-head bolts (3-1/4 inch). 4. Insert the bolts through the hinged welded tube openings, hinges, and straps (Figure 3). Preparing the Booms Parts needed for this procedure: Hydraulic manifold block Hydraulic fitting Procedure The booms are set at the factory to travel downward no... - Page 5 9. Tighten the jam nut on each rod until it is snug. 10. Remove the hydraulic block cover plate. 11. Label all the hoses connected to the hydraulic manifold block (ports C1 through C4), and disconnect them from the block. Note: Loosen the 2 hydraulic connectors on the right side and the gauge port (Figure 6).
-
Page 6: Boom Cradle Arm
Replacing the Boom Cradle Installing the Sonic Boom Arms Sensors Parts needed for this procedure: Parts needed for this procedure: Boom cradle arm Sonic boom sensor Caps Bracket Programming plug Procedure Sensor cover The new boom cradle arms allow the booms to fold up Lower sensor housing without contacting each other, preventing any possible Cap tube... - Page 7 G017148 Figure 9 Rear view G017150 1. Mounting bracket (2) 2. Locknuts (1/4 inch) (12) 2. Install the sensor guard bracket onto the mounting bracket with 2 bolts (5/16 x 3/4 inch) and 2 flange nuts (5/16 inch) as shown in Figure 10. Figure 11 For a covered boom only 1.
- Page 8 G017158 Figure 14 1. Sideways “T” 3. Notch 2. Arrows aligned 4. Sensor 6. Insert the sensor into the lower sensor housing, and secure it with 2 large nuts provided with the sensor (Figure 13). Note: Discard the lock washers that come with the sensors.
-
Page 9: Locknut (1/4 Inch)
Mounting the Electronic Control Parts needed for this procedure: Electronic controller Mounting bracket Bolt (1/4 x 1-1/8 inch) Locknut (1/4 inch) g025940 Figure 16 Procedure 1. Bolt 4. Cover 2. Bracket 5. Nut Important: In order to complete the installation, a 3. -
Page 10: Rocker Switch
Note: The controller connection is keyed and can be 4. Route the wiring harness to the hydraulic manifold (Figure 17). connected in only one way. 5. Route the electronic control terminal on the wiring 2. For model 1750, connect the wiring harness to the harness through the knockout hole, but do not connect electronic controller by routing the wiring harness the terminal to the controller. - Page 11 7. Install the battery terminal on the wiring harness to the 6. Install the right-hand side cover on the center console positive (+) terminal of the battery. using the fasteners that you removed in step 1. 7. Route the wiring harness to the back of the vehicle 8.
-
Page 12: No Parts Required
Note: The green light on the sonic boom switch will flash rapidly, indicating that the sonic boom system is in calibration mode. You now have 20 seconds to use the Raise and Lower boom switches to set the desired distance from the booms to the ground. After the 20 Calibrating the Sonic Booms seconds, the green light will flash slowly. - Page 13 Operating the Sprayer Operation Important: When operating the machine over especially Using the Controls uneven terrain, reduce the ground speed to prevent the booms from striking the ground. The Sonic boom switch is located on the dashboard and has 2 settings: Automatic and Manual. Maintenance •...
- Page 14 Off. 2. The light is burned out. 2. Replace the light. 3. The electronic controller or wiring is 3. Contact an Authorized Toro Distributor. damaged. One or both booms malfunction; the sonic 1. There is a minor system error.
- Page 15 Notes:...
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.