Advertisement
Quick Links
Trailer Light Kit
Side-Dump Mixers
Model No. 68062
WARNING
CALIFORNIA
Proposition 65 Warning
This product contains a chemical or chemicals
known to the State of California to cause cancer,
birth defects, or reproductive harm.
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
© 2013—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
Bracket
Bolt
Nut
Wire harness
Cable clamp
Edge clip—parallel
Edge clip—perpendicular
Fir-tree mount
Bolt
Nut
Cable tie
Grommet
Light
License-plate holder
Nut
Reflector
Bolt
Nut
No parts required
Register at www.Toro.com.
Form No. 3377-600 Rev B
Installation Instructions
Qty.
2
4
Install the brackets.
4
1
7
4
1
2
Install the wires.
5
5
5
2
2
1
Install the lights.
4
2
2
Install the reflectors.
2
–
Replace the light bulbs.
Original Instructions (EN)
All Rights Reserved *3377-600* B
Printed in the USA
Use
Advertisement
Related Manuals for Toro 68062
Summary of Contents for Toro 68062
- Page 1 Form No. 3377-600 Rev B Trailer Light Kit Side-Dump Mixers Model No. 68062 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
-
Page 2: Installing The Brackets
Installing the Brackets Installing the Wires Parts needed for this procedure: Parts needed for this procedure: Wire harness Bracket Cable clamp Bolt Edge clip—parallel Edge clip—perpendicular Fir-tree mount Procedure Bolt 1. Align the bolt holes of a bracket with the bolt holes in the side frame rail under the cowl (Figure 1). - Page 3 3. Route the wire harness as shown in Figure 4, Figure 7, or Figure 8, depending on the model. G021626 Figure 4 Concrete mixers (frame underside shown for clarity) 1. Edge clip 3. Wire harness 2. Excess wire 4. Cable clamp Note: Some concrete mixers (Figure 4) have a hole in the rear vertical part of the frame;...
- Page 4 G021630 Figure 6 Frame without hole 1. Edge clip location G021627 Figure 7 Belt-drive mortar mixers (frame underside shown for clarity) 1. Edge clip 3. Wire harness 2. Excess wire 4. Cable clamp...
- Page 5 G021628 Figure 8 Gear-box mortar mixer (frame underside shown for clarity) 1. Edge clip 3. Wire harness 2. Excess wire 4. Cable clamp 4. Use cable clamps and edge clips to secure the wire harness along the inside of the frame (Figure 9). G020912 G020980 Figure 9...
-
Page 6: Installing The Lights
Installing the Lights Parts needed for this procedure: Light License-plate holder G02091 Figure 11 Procedure 1. Grommet 3. Cable tie 2. Fir-tree mount 1. Position the license-plate holder onto the posts of the light with the clear bottom lens, so that the clear lens is facing the license-plate holder (Figure 13). - Page 7 G020914 Figure 14 Right light G020921 Figure 16 1. Green wire—stop and turn 3. White wire—ground Model 68024 2. Brown wire—tail light 1. Reflector 2. Insert a bolt through the reflector and the frame, and install a nut on the other side. 3.
-
Page 8: Replacing The Light Bulbs
Replacing the Light Bulbs No Parts Required Replacing the Rear-facing Bulbs Note: The left rear-facing bulb also illuminates license plate. G020830 Figure 18 1. Use a screwdriver to remove the 4 screws from the large square lens on the light (Figure 17). 2.