Advertisement
NOTE: Make sure that the water level in the tank does not go above the 'MAX' level indicated on the scale marking.
6.2.7.
Once water is filled, take extra care to ensure that you DO NOT tilt the cooler.
6.2.8.
Keep the unit on a flat, stable ground without any obstacles near it when operating or moving it.
6.2.9.
Connect to the mains supply.
6.3.
CONTROL PANEL (fig.3)
SPEED
6.3.1.
Select the relevant speed button to start the unit. There are three options – Low, Medium or High.
SWING
6.3.2.
Press this button to start or stop louvre oscillation from left to right.
HUMIDIFIER
6.3.3.
To begin humidification press the labelled button.
NOTE:
The fan needs to be running before either swing or humidifier functions operate.
6.3.4.
INTERNAL LOUVRES
Vertical adjustment of air stream angle can be achieved by using the small levers on the right hand side of the front grille (fig.1.2).
7. CLEANING
WARNING! Disconnect from mains supply before removing the filters or carrying out any cleaning or maintenance.
‰
DO NOT use harsh detergents or chemical cleaners or solvents as they may damage the surface of plastic components.
8
7.3.1.
MAIN BODY
Use a soft duster to dust off all surfaces.
Clean the air filter and filter cover (fig.2.4, fig.2.5) using a vacuum cleaner on a regular basis (refer to 7.3.2.)
Wipe all the parts with a soft damp (not wet) cloth dipped in mild soapy water. CAUTION: Ensure that water doesn't get inside the
unit. Use a dry cloth to thoroughly dry the unit before turning on.
7.3.2.
AIR INLET COVER AND INNER FILTER
Unclip the air inlet cover. Vacuum clean the inner filter. Replace the inner filter if necessary by pulling up the clip on the top edge and
easing the inner filter out. Vacuum clean the inner screen. Fit new filter (if necessary) and clip the air inlet cover back in place.
WATER TANK
7.3.3.
WARNING! Unplug the unit from the mains supply before removing the water tank.
‰
When the unit will not be used for some time, empty the water from the water tank. Use mild soap and water to clean the water tank.
Allow it to air dry or wipe dry using a soft cloth. Make sure the water tank is completely dry before storage. This helps prevent any
mould or mildew inside the water tank. Empty the water in the ice blocks and dry out before storage. Make sure the filter, filter cover
and water tank are replaced in position before switching on again.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
BATTERY REMOVAL:
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak's registered compliance scheme. Jack
Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
01284 703534
sales@sealey.co.uk
Original Language Version
fig.3
www.sealey.co.uk
SAC04 Issue 1 09/05/19
Advertisement
