English CORDLESS GRINDER DCG412 Congratulations! EC-Declaration of Conformity You have chosen a D WALT tool. Years of experience, thorough Machinery Directive product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data...
Page 7
*Date code 201811475B or later **Date code 201536 or later English Batteries Chargers/Charge Times (Minutes) Weight (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119 Cat # DCB546 18/54 6.0/2.0 1.05 DCB547 18/54 9.0/3.0 1.46 135* 135* DCB548 18/54 12.0/4.0 1.44 DCB181 0.35...
English h ) Do not let familiarity gained from frequent use of contacts eyes, additionally seek medical help. Liquid tools allow you to become complacent and ignore ejected from the battery may cause irritation or burns. tool safety principles. A careless action can cause severe e ) Do not use a battery pack or tool that is damaged injury within a fraction of a second.
English FURTHER SAFETY INSTRUCTIONS FOR ALL chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. OPERATIONS If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After Causes and Operator Prevention inspecting and installing an accessory, position of Kickback...
Page 10
English Safety Warnings Specific for Wire Brushing amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel Operations fragments and accidental contact with wheel and sparks a ) Be aware that wire bristles are thrown by the brush that could ignite clothing.
English When using a cable reel, always unwind the cable completely. Do not disassemble charger; take it to an authorised • service centre when service or repair is required. Incorrect Important Safety Instructions for All Battery reassembly may result in a risk of electric shock, electrocution Chargers or fire.
English pack charging mode. This feature ensures maximum battery charger as battery pack may rupture causing serious pack life. personal injury. A cold battery pack will charge at a slower rate than a warm • Charge the battery packs only in D WALT chargers.
The Use Wh rating might indicate 108 Wh (1 battery implied). Battery Type Storage Recommendations The DCG412 operates on a 18 volt battery pack. 1. The best storage place is one that is cool and dry away These battery packs may be used: DCB181, DCB182, DCB183, from direct sunlight and excess heat or cold.
English Package Contents Intended Use The DCG412 cordless angle grinder has been designed for The package contains: professional cutting, light-duty material removal and wire- 1 Angle grinder brush applications. 1 Guard DO nOT use grinding wheels other than centre depressed 1 Side handle wheels and flap discs.
Page 15
English subject to variation based on product components, temperature 3. Keeping the guard release lever open, push the guard down and end-user application. until the guard lugs engage and rotate them in the groove on the gear case hub. Release the guard release lever. Attaching Side Handle (Fig.
Page 16
English Mounting Non-Hubbed Wheels (Fig. A, E) Mounting and Removing Hubbed Wheels (Fig. A) nOTE: The Type 27 guard supplied with grinder MUsT be used. nOTE: The Type 27 guard supplied with grinder MUsT be used. WARNING: Failure to properly seat the flanges and/or Hubbed wheels install directly on the threaded spindle.
English 1. Place the unthreaded backing flange on spindle with the 6 workpiece near the line of cut and near the edge of the raised centre facing up. The raised centre on the backing workpiece on both sides of the wheel. flange will be against the wheel when the wheel is installed.
Page 18
English WARNING: Hold the side handle and body of the tool 4. Once a cut is begun and a notch is established in the firmly to maintain control of the tool at start up and workpiece, do not change the angle of the cut. Changing during use and until the wheel or accessory stops rotating.
English Precautions to Take When Wire Brushing Paint insulation in the machine becoming degraded with a potential risk of an electrical shock. 1. Wire brushing of lead based paint is NOT RECOMMENDED To avoid build-up of metal swarf inside the machine, we due to the difficulty of controlling the contaminated dust.
English Pop-off Brushes materials. Please recycle electrical products and batteries according to local provisions. Further information is available at The motor will be automatically shut off indicating that the www.2helpU.com. carbon brushes are nearly worn out and that the tool needs Rechargeable Battery Pack servicing.
Page 21
English GRINDING AND CUTTING ACCESSORY CHART guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Threaded clamp nut Wire wheels with threaded nut Type 27 guard Wire wheel...
Page 22
English GRINDING AND CUTTING ACCESSORY CHART (cont.) guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Diamond cutting wheels Type 1 Guard Cutting wheel Type 27 Guard Threaded clamp nut...
Page 24
Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)