Advertisement
Quick Links
Hopper Vibrator Kit
ProPass Top Dresser and MH-400 Material Delivery Unit
Model No. 44723
Safety
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
1. On
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
132-8388
2. Off
Register at www.Toro.com.
Installation
Note:
Lay out the harnesses on the machine to
determine the mounting locations of the harness
components. Use the included cable ties to retain any
surplus cable. Also, if you need to shorten or lengthen
a harness section, use the included wire splices. Heat
the integrated heat-shrink tubing until it shrinks tight
onto the wires.
Important:
sure to use the proper gauge of wire.
Preparing the Machine
1.
Park the traction unit and the topdresser on
a level surface and lower the attachments (if
equipped).
2.
Engage the parking brake, shut off the engine,
and remove the key.
Installing the Kit on a
ProPass Top Dresser
Installing the Switch Harness and
the Switch on a Workman Utility
decal132-8388
Vehicle
1.
Route the switch harness shown in
through the vehicle, starting at the front, along
the existing harness.
Note:
be in the rear of the vehicle near the high-flow
hydraulics port
Form No. 3426-889 Rev A
Installation Instructions
If you lengthen the harness, make
The vibrator-harness connector should
(Figure
1).
Original Instructions (EN)
All Rights Reserved *3426-889* A
Printed in the USA
Figure 4
Advertisement
Related Manuals for Toro 44723
Summary of Contents for Toro 44723
- Page 1 Form No. 3426-889 Rev A Hopper Vibrator Kit ProPass Top Dresser and MH-400 Material Delivery Unit Model No. 44723 Installation Instructions Safety Installation Note: Lay out the harnesses on the machine to Safety and Instructional determine the mounting locations of the harness components.
-
Page 2: Installing The Power Harness
g031580 Figure 1 Switch harness 1. Switch connector 3. Vibrator-harness connector 2. Power-harness connector Insert the switch, with the rounded side up, into the hole in the dash panel and connect the harness to the switch (Figure 2 Figure g031583 Figure 3 1. - Page 3 g031582 Figure 5 Battery harness (optional) g024368 1. Switch-harness connector 3. Positive terminal (red wire) Figure 7 2. Fuse 4. Ground terminal (black 1. Carriage bolt (4) 3. Vibrator wire) 2. Mounting plate 4. Nut (4) Connect the grounding terminal to the ground block of the vehicle.
- Page 4 Note: Remove a knockout plug from an available If the fuse block is full, add a new fuse switch location on the dash. block, connect the fuse-block connector to the new fuse block, then add a 15 A fuse to the new If no switch locations are available, install the fuse block.
- Page 5 Note: Locate 1 hole, then use the mounting plate as a template for drilling the remaining holes. g031585 Figure 14 1. Switch-harness connector 2. Vibrator connector Use cable ties to secure all the wires along the hydraulic lines all the way to the switch-harness connector.
- Page 6 Installing the Kit on an Cut off and discard the switch-harness connector and strip 10 mm (3/8 inch) of insulation off the MH-400 Material Handler wires (Figure 15). with an Outcross 9060 Traction Unit Installing the Wire Harness Note: Following these instructions allows you to use the accessory switch that is already installed on the g272997 Figure 15...
- Page 7 Insert the wires through the small hole in the boot. Install the black wire to the pin 1 terminal and the white wire to the pin 7 terminal (Figure 17). Tighten the screws to secure the wires. Assemble the 7-pin connector. Installing the Vibrator g024368 Drill 4 mounting holes (7 mm or 9/32 inch) on...
-
Page 8: Operation
Operation Using the Hopper Vibrator Press the top of the switch to turn the vibrator on (Figure Figure 22, or Figure 23). Press the bottom of the switch to turn the vibrator off. g273085 Figure 23 g267694 Figure 21 Tractor Outcross 9060 Traction Unit 1.