Table of Contents
Advertisement
--------------------------------------------------------------------------HMcS~4AC
(Note 1) Pull-up MOS current and output buffer current are excluded.
(Note 2) The MCU is in the reset state. The input/output current does not flow.
Test Conditions:
MCU state;
• Reset state in Operation Mode
Pin state;
• RESET, TEST ... Vee voltage
• D.
-0"
R3- R9 '" Vee voltage
• D.-DIS, RO-R2, RAQ' RA1'" Vdisp voltage
(Note 3) The timer/counter operate with the fastest clock and input/output current does not flow.
Test Conditions:
MCU state;
• Standby Mode
• Input/Output; Reset state
• TIMER-A; +2 prescaler divide ratio
• TIMER-S; +2 prescaler divide ratio
• SER IAL Interface ; Stop
Pin state;
• RESET .. ·GND voltage
• TEST ... Vee voltage
• 0.-0"
R3-R9 .. · Vee voltage
• D. -DIS, RO-R2, RAQ, RA1 ... Vdisp voltage
(Note 4) The timer/counter operate with the slowest clock and input/output current does not flow.
Test Conditions:
MCU state;
• Standby Mode
• Input/Output; Reset state
• TIMER-A; +2048 prescaler divide ratio
• TIMER-S; +2048 prescaler divide ratio
• SERIAL Interface; Stop
Pin state;
• RESET. .. · GND voltage
• TEST ... Vee voltage
• D.
-0"
R3- R9 ... V cc voltage
• D. -DIS, RO- R2, RAQ, RA1 .. , V disp voltage
(Note 5) Pull-down MOS current is excluded.
(Note 6) When fosc=x[MHz] , the Current Dissipation in Operation mode and Standby mode are estimated as follows:
max. value (fosc=X [MHz] )
=~x
max. value (fosc= 6 [MHz])
• INPUT/OUTPUT CHARACTERISTICS FOR STANDARD PIN
(Vee
=
4.5V to 6V,GND
=
OV, Vdisp
=
Vee-40V to Vee, Ta
=
-20 to +75°C, if not specified.)
Item
Symbol
Pin Name
Test Conditions
Input "High"
V IH
Do -
03,
Voltage
R3 - R5, R9
Input "Low"
V IL
Do -
03,
Voltage
R3- R5, R9
00 - 03,
Output "High"
V OH
R3- R8
-loH
=
1.0 mA
Voltage
Do -
03,
-IOH
=
0.01 mA
R3- R8
Output "Low"
VOL
00 - 03,
IOL
=
1.6 mA
Voltage
R3- R8
Input/Output
\lILI
00 - 03,
Yin
=
OV to VCC
Leakage Current
R3- R9
Pull-Up MOS
-Ip
00 - 03,
Vee - 5V
Current
R3- R9
Yin
=
OV
(Note 1) Applied to I/O pins with "CMOS" Output selected by mask option.
(Note 2) Pull-up MOS current and output buffer current are excluded.
(Note 3) Applied to I/O pins "with Pull-up MOS" selected by mask option.
301
Value
min
typ
0. 7V ee
-
-0.3
-
Vee- 1 . O
-
Vee- 0 . 3
-
-
-
-
-
30
60
Unit
Note
max
Vee+ 0 . 3
V
0. 22V ec
V
-
V
1
-
V
1
0.4
V
1
p.A
2
120
p.A
3
Advertisement
Table of Contents
