Sony CDX-1000RF Operating Instructions page 2

Connections
Caution
•This unit is designed for negative ground 12 V DC operation only.
•Before making connections, disconnect the ground terminal of the car battery to avoid short circuits.
•Connect the yellow and red power input leads only after all other leads have been connected.
•Be sure to connect the red power input lead to the positive 12 V power terminal which is energized
when the ignition key is in the accessory position.
•Run all ground wires to a common ground point.
•Connect the yellow cord to a free car circuit rated higher than the unit's fuse rating.
If you connect this unit in series with other stereo components, the car circuit they are connected to
must be rated higher than the sum of the individual component's fuse rating.
If there are no car circuits rated as high as the unit's fuse rating, connect the unit directly to the
battery.
If no car circuits are available for connecting this unit, connect the unit to a car circuit rated higher
than the unit's fuse rating in such a way that if the unit blows its fuse, no other circuits will be cut
off.
•The use of optical instruments with this product will increase eye hazard.
Reset button
When the installation and connections are complete, be sure to press the reset button with a ball-point
pen, etc.
AMS
SHUF DSPL
REPEAT OFF
Reset button
Connection example
To a metal point of the car
First connect the black ground lead, then connect the yellow
and red power input leads.
To the +12 V power terminal which is energized in
the accessory position of the ignition key
Be sure to connect the black ground lead first.
To the +12 V power terminal which is energized at
all times
Be sure to connect the black ground lead first.
Rotary commander RM-X4S*
(not supplied)
If you have a Sony car audio with the Sony BUS terminal, the optional source selector
XA-107 can be used in your system.
Sony car audio
AUDIO IN BUS CONTROL IN
AUDIO OUT MASTER
Source selector
XA-107
AUDIO IN
AUDIO OUT
CDX-1000RF
Parts for Installation and Connections
The numbers in the list are keyed to those in the instructions.
1 2
4 5
7 8
4
Caution
Cautionary notice for handling the bracket 1.
Handle the bracket carefully to avoid injuring your fingers.
Black Blue/White
To AMP REMOTE IN
of the car audio*
0.5 m 0.5 m
AMP REMOTE OUT
(1 ft. 8 in.) (1 ft. 8 in.)
Max. supply current 0.3 A
Fuse
Red
0.5 m
(1 ft. 8 in.)
1 You can only connect a car audio which has both a remote
*
amplifier input (AMP REMOTE IN) and an audio input (AUDIO IN).
Fuse
Note
Yellow
Do not connect an external amplifier to the audio output (AUDIO
OUT) of this unit. Otherwise, the volume of the connected
0.5 m
speakers cannot be adjusted.
(1 ft. 8 in.)
AUDIO OUT
8
L
R
AUDIO OUT
RCA pin cord
(not supplied)
REMOTE IN
1.9 m (6 ft. 3 in.)
2
0.5 m
(1 ft. 8 in.)
Car audio
3
Antenna connector*
* 2 You can also control the following functions with the rotary cammander
RM-X4S:
Power on – Press SOURCE.
Power off – Press OFF.
Locate a specific track
– Rotate the SEEK/AMS control momentarily and release.
Locate a specific point within a track
– Rotate the SEEK/AMS control and release when the desired point is found.
Adjust the volume – Rotate the volume control.
* 3 An adaptor (optional) may be necessary for your car and car audio system.
In such a case, consult your dealer.
Installation
Precautions
•Do not tamper with the four holes on the upper surface of the unit. They are for tuner adjustments to be
3
done only by service technicians.
•Choose the installation location carefully so that the unit will not hamper the driver during driving.
•Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or
hot air from the heater, or where it would be subject to dust, dirt, or excessive vibration.
•Use only the supplied mounting hardware for a safe and secure installation.
Mounting example
6
Installation in the dashboard
1
1 8 2
m m
(7
1
2
9
1
With the TOP marking up
4
5
With the TOP marking up
1
Mounting the unit in a Japanese car
You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer.
TOYOTA
7 max. size 5 6 mm
( 7 / 1 / in.)
32 4
Bracket
To AUDIO IN
1
of the car audio*
Existing parts supplied with your car
Note
From car antenna
To prevent malfunction, install only with the supplied screws 7.
Removing the unit
Speaker system
Insert the supplied tool 9 between the unit and the frame, and rotate 90° to
1
release the hidden mounting spring. Repeat on the opposite side and remove
the frame.
13
10 mm ( / in.)
32
Mounting angle adjustment
Adjust the mounting angle to less than 60°.
2 3
/
4 in .)
5 3 m
m
(2 1
/
in .)
8
Bend these claws, if necessary.
Note
To prevent malfunction, install
only with the supplied screws 7.
To support the unit
1
2
NISSAN
7 max. size 5
( 7 / 1 / in.)
32 4
Car audio with FM tuner
to dashboard/center console
7 max. size 5 6 mm
( 7 / 1 / in.)
32 4
CDX-1000RF
Bracket
2 Insert a flathead screwdriver between the bracket and mounting spring. Gently
pry the spring toward the unit while pulling the unit out a little. Repeat on the
opposite side and remove the unit.
9
90º
max. size 5 6 mm
7
7 1
( / 32 / 4 in.)
6 7
6
6 7
max. size 5 6 mm
7 1
( / 32 / 4 in.)
Fire wall
2
Dashboard
3 max. size M4 6 mm
( 3 / 1 / in.)
16 4
4
1
6 mm
Car audio with FM tuner
to dashboard/center console
7
max. size 5 6 mm
( 7 / 1 / in.)
Bracket 32 4
CDX-1000RF
Bracket
Existing parts supplied with your car
4 mm ( 3 / in.)
16