Bosch Benchmark 500 Series Installation Manual
Hide thumbs
Also See for Benchmark 500 Series:
- Installation manual (64 pages) ,
- Installation manual (56 pages) ,
- Installation manual (39 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bosch Benchmark 500 Series
Summary of Contents for Bosch Benchmark 500 Series
- Page 1 Built-In Oven Installation Manual 500/800/Benchmark™ Series HBL5351UC, HBL5451UC, HBL5551UC, HBL5651UC, HBL8442UC, HBL8451UC, HBL8461UC, HBL8642UC, HBL8651UC, HBL8661UC, HBLP451LUC, HBLP451RUC, HBLP451UC, HBLP651LUC, HBLP651RUC, HBLP651UC, HBN5451UC, HBN5651UC, HBN8451UC, HBN8651UC...
-
Page 3: Table Of Contents
Before Calling Service ....13 Cabinet Dimension Requirements . 15 Dimensions for 27” Single Oven Units . . 15 This Bosch Appliance is made by BSH Home Appliances Corporation 1901 Main Street, Suite 600... -
Page 5: Safety Definitions
9 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Appliance Handling Safety Safety Definitions Do not lift appliance by door handle. Remove the door for easier handling and installation. See instructions in Use and Care Manual. 9 WARNING This indicates that death or serious injuries may Unit is heavy and it is recommended that at least two occur as a result of non-observance of this warning. - Page 6 9 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Refer to data plate for more information. See "Data Plate" under "Service" for data plate location. Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections and grounding must comply with all applicable codes.
-
Page 7: Preparation
Checklist Preparation Use this checklist to verify that you have completed each step of the installation process. This can help you avoid mistakes. Before You Begin ___ 1. Before installing the oven, be sure to verify the cabinet dimensions are correct for your unit and Tools and Parts Needed the required electrical connections are present. -
Page 8: Dimensions And Cabinet Requirements
Combination Oven Pre-Assembly Dimensions and Cabinet Requirements Cabinet requirements vary depending on the model to be support. This supporting base must be well secured to installed. Please consult the “Cabinet Dimension the floor/cabinet and must be level. Requirements” section at the back of this installation •... -
Page 9: Installation
Installation This installation manual provides instructions for the power supply installation of single ovens and double ovens. junction box black wires red wires Electrical Installation green or bare All model ovens on the front cover of this installation wire instruction manual are dual rated, designed to be connected to either 208 or 240V AC, 60 Hz, 4 wire, single- green wire white wires... -
Page 10: Installing The Oven Unit Into The Wall
Combination Oven Pre-Assembly Installing the Oven Unit into the Wall Cabinet NOTICES Before installing the oven, be sure to verify the cabinet dimensions and electrical connections. Check that the cabinet opening is level and plumb for correct installation. For Best Installation It is recommended to remove the oven door (bottom hinge models only) to help reduce the unit weight and provide easier access to the handholds located inside the oven. - Page 11 Lifting Recommendations Vary Dependent Upon Oven Door Type Bottom Hinge Door Side Hinge Door Lift Locations (with door(s) removed) Lift Locations (with lower door opened to 90°-110°) Lift points (1) on the front of the unit are for lifting from the sides of the unit.
-
Page 12: Installing The Oven
Installing the Oven 4. Holding the door firmly on both sides and using both hands, WARNING close the door gently until it stops against • Make sure oven is cool and power to the oven the latch levers, about has been turned off before removing the door. 30º... -
Page 13: Installing The Oven Into The Cabinet
Installing the Oven into the Cabinet (all ovens) 1. The unit and its bottom packaging (wood and styrofoam base) should be positioned close to and in front of the cabinet opening prior to beginning to lift the unit into place. 2. -
Page 14: Ovens With Bottom Hinge Doors Only
Ovens with Bottom Hinge Doors Only Ovens with Side Hinge Doors Only Re-Install the oven doors: Side Hinge Door Aligment Note: Only align the side hinge oven doors after the unit is 1. Hold the door firmly in fully installed into the cabinet. both hands. - Page 15 Side Hinge Door Alignment Procedure 1. Open the door to approximately 135°. 2. Using a Torx T-20 star- head screwdriver, loosen the 3 screws (A) on the lower hinge by 1 to 2 full turns. Note: All adjustment is made with the lower hinge only.
- Page 16 Side Hinge Door Opening/Closing Troubleshooting Guide Primary observation Additional observations Cause Solution The door does not pull The side edge of the inner The installation is Check the installation of the unit in the itself closed and feels door (on the handle side of causing the side cabinetry.
-
Page 17: Before Calling Service
5. If installing a double oven, test the second oven as well. 6. If any of the tests do not result as explained above, contact Bosch service for assistance. Otherwise, the installation is complete at this time. Before Calling Service See the Use and Care Manual for troubleshooting information. - Page 18 Single Ovens, Side Hinge Note: The rating plates (A) are opposite the door hinge. For left hinge doors, the rating plates will be on the door trim on the right hand side of the door. For right hinge doors, the rating plates will be on the door trim on the left hand side of the door.
-
Page 19: Cabinet Dimension Requirements
Cabinet Dimension Requirements It is good practice, when an oven is installed at the end of a Single Oven 27” Flush Mount cabinet run, adjacent to a perpendicular wall, or cabinet Installation door, to allow at least 1/4” (6 mm) space between the side of the oven and the wall/door. -
Page 20: Double Oven 27" Flush Mount Installation
Double Oven 27” Flush Mount Single Oven 30” Flush Mount Installation Installations Flush installation requires two side cleats to be attached Flush installation requires two side cleats to be attached inside the cabinet frame, recessed from the front. inside the cabinet frame, recessed from the front. Dimensions for 30”... -
Page 21: Dimensions For 30" Double Oven Units
Dimensions for 30” Double Double Oven 30” Flush Mount Installion Oven Units Double Oven 30” Flush installation requires two side cleats The cabinet opening must be plumb and the base must be to be attached inside the cabinet frame, recessed from the flat and level and capable of supporting a weight of at least front. - Page 22 English 18 9001065629 Rev A...