Advertisement
A
Light Control
Module 1
Bedroom
Livingroom
Clock Radio with Light Control
D.S.T
SUMMER T. CLOCK
AUTO
1+2
A+B
1+2
ALARM
RANDOM
RADIO
A
A
1
B
OFF
ON
BUZZER
B
2
HOME SECURITY LIGHT CONTROL SYSTEM
SNOOZE
/ DATE / SLEEP OFF
LIGHT control
ALARM dial
dial (outside)
(inside)
ALARM
LIGHT CONTROL
A
B
RANDOM
1
ON
TIME
OFF
TIME
AM
PM
Light Control Module
Light control code
ID CODE
1 2
16
1
2
15
3
14
4
13
5
12
6
11
7
10
8
9
ON lamp
LIGHT ON/OFF
AC IN
How the Home
Security Light
Light Control
Control System
Module 2
Works
You can easily assemble the Home Security Light
Control System by using the main unit and the
supplied Light Control Modules (2 modules are
included in the package). The main unit sends
signals through your house wiring system to the
Light Control Modules and automatically turn
the connected lights on or off to give your home
a lived-in look while you are away.
About the ID CODE
You can choose from 16 transmission codes to
prevent signal interference from other similar
systems used in the same household or
apartment complex, etc.
Guestroom
About the Light Control
Code
You can choose from Light control code 1 or 2 on
the Light Control Module. Light control code 1
and 2 are linked to LIGHT•1 and 2, respectively,
of the main unit, and can be controlled
TIME SET
separately.
ID CODE
LIGHT
Installing the
1 2
BAND
16
15
3
1
14
4
13
5
Battery
12
6
11
7
2
FM
AM
10
8
9
To keep accurate time, your Dream Machine
OFF RADIO
requires one 6F22 battery (not supplied), in
addition to the house current. The battery keeps
the clock operating in the event of a power
ALARM RESET
SLEEP
interruption. Before setting the time and light
control on your Dream Machine, open the lid at
the bottom of the unit, install the battery with
correct polarity and then close the lid.
Note
When you are not going to use the unit for a long
time, remove the battery to avoid damage from
battery leakage and corrosion.
FM wire antenna
To check when to replace the
battery
To check the remaining battery power, unplug
the power cord from the wall outlet and plug it
in again after a few minutes. If the displayed
time is incorrect or the display does not show at
AC power cord
all, replace the battery with a new one.
Installing the Home
Security Light
TUNE
Control System
Complete this built-in ON/OFF control setup
VOL
before you proceed to the next section. This will
enable the successful control of your lights from
your Dream Machine.
1
Turn ID CODE selector on the main
unit with a coin or a flat-blade
2
AUTO
screwdriver to select the desired code.
SLEEP
2
Turn the ID CODE selector on the
module with a coin or a flat-blade
screwdriver to match the code on the
main unit.
3
Set the Light control mode switch to 1
or 2 on the modules.
1 is for LIGHT•1 and 2 is for LIGHT•2.
4
Insert the module to a desired wall
outlet in your house.
5
Insert the plug of a desired light fixture
to the module and turn on the power
switch for the light.
Note
You may also turn the light on or off manually
using the LIGHT•ON/OFF button on the module.
Cautions
• Do not connect light fixtures that use over
300 W (MAX), 2A (MAX).
• The system should only be used to control
to a wall
lights. Do not connect a coffee maker, toaster,
or other heating appliances, as this may lead to
outlet
a fire hazard.
To check the control function
1
Turn LIGHT CONTROL to the right side
from OFF to AUTO 1+2.
"AUTO" will appear in the display.
2
Confirm if the light is on.
If the light is not lit, repeat steps 1 to 5 again
in "Installing the Home Security Light
Control System" or check that the switch on
the light stand is turned on.
Setting the Light
Control ON/OFF
times
(see Fig. A)
You can preset the ON/OFF time of your lights.
Before setting the lights, be sure to set the remote
control function (See "Installing the Home
Security Light Control System").
Example: To set the ON/OFF time for LIGHT•1.
1
To set the ON time, press LIGHT•1 for
a few seconds.
A short beep sounds. The "ON TIME" and
"1" indications and the hour will flash in the
display.
2
Press either TIME SET + or – until the
desired hour appears in the display.
3
Press LIGHT•1 to set the minutes.
The minutes will flash in the display.
4
Press either TIME SET + or – until the
desired minutes appear in the display.
5
Press LIGHT•1 to set the OFF time.
A short beep sounds. The "OFF TIME" and
"1" indications and the hour will flash in the
display.
6
Press either TIME SET + or – until the
desired hour appears in the display.
7
Press LIGHT•1 to set the minutes.
The minutes will flash in the display.
8
Press either TIME SET + or – until the
desired minutes appear in the display.
9
Press LIGHT•1.
Two short beeps sound to indicate successful
presetting.
Note
You can check the ON/OFF time setting by
pressing LIGHT•1 or 2.
Turning the lights ON/OFF
Turn the light control dial to "AUTO 1+2" to turn
on the lights immediately.
Turn the light control dial to "OFF" to turn off
the lights immediately.
Note
The AUTO 1+2 function can be used as an instant
light control switch besides to control the ON/
OFF times of the lights (see Setting the Light
Control Mode - AUTO 1+2). However, this
setting will turn the lights on and off as
described in Setting the Light Control Mode.
Setting the Light
Control Mode
If you adjust the Light Control dial to the
position shown in the table, the Light Control
Modules will operate as described below.
Light Control
The Light Control
Position
Modules will
OFF
turn off.
turn on and off repeatedly
every 2 hours for Module 1
AUTO 1+2
and every 3.5 hours for
Module 2.
turn on/off, Module 1 at the
setting of LIGHT•1 and
1+2
Module 2 at the setting of
LIGHT•2.
turn on/off for Module 1
only, the ON/OFF time for
1
LIGHT•1 will operate as
preset.
turn on/off for Module 2
only, the ON/OFF time for
2
LIGHT•2 will operate as
preset.
Notes
• A beep will sound each time you reset the
LIGHT CONTROL dial.
• The ON/OFF time for AUTO is factory set.
• If you do not set the preset time for LIGHT•1
and 2, the Light control mode will not operate
even when you set the LIGHT CONTROL dial to
1, 2 and 1+2.
To Use the Random
Function
You can randomize the on and off times to give
your home a lived-in look while you are away.
Set the RANDOM switch to ON.
The on and off times will operate as preset on the
first day, with a 24 minutes advance on the
second day, a 48 minutes advance on the third
day, and a 36 minutes advance on the fourth day.
The four day cycle will then be repeated from the
fifth day.
AUTO mode with or without the RANDOM
To stop the alarm
function:
When the RANDOM function is not activated,
Press ALARM RESET while the alarm is
LIGHT•1 will alterate between on and off every 2
activated.
hours and LIGHT•2 every 3.5 hours.
The alarm will come on at the same time the next
When the RANDOM function is activated, the
day.
ON/OFF times will follow the cycles below:
LIGHT•1
To cancel the alarm
5 hours
2 hours
4 hours
3 hours
ON/OFF
ON/OFF
ON/OFF
ON/OFF
Turn ALARM dial to OFF so that neither
the "A" nor "B" indication is displayed.
Notes
LIGHT•2
• The alarm does not function, unless you set
3.5 hours
2 hours
5 hours
2.5 hours
the clock, ALARM•RADIO A or
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ALARM•BUZZER B function.
• If both the radio and buzzer alarm are set for
the same time, the radio alarm takes
precedence.
• You can check the alarm time setting by
To cancel the RANDOM function, set RANDOM
pressing ALARM•RADIO A or
to OFF.
ALARM•BUZZER B.
To doze for a few more
Setting the Clock
minutes
1
Plug in the clock radio.
1
Press SNOOZE/DATE/SLEEP OFF.
"AM 12:00" will flash in the display.
The radio or buzzer will shut off but will
2
Press CLOCK for a few seconds.
automatically come on again after about
You will hear a beep and the year will start to
8 minutes. You can repeat this process as
flash in the display.
many times as you like.
3
Press TIME SET + or – until the correct
year appears in the display
4
Press CLOCK once.
Setting the Sleep
5
Repeat steps 3 and 4 to set the month,
date, hour, and minutes.
Timer
After setting the minutes, press and release
CLOCK to activate the clock.
You can enjoy falling asleep to the radio using
the built-in sleep timer that turns off the radio
• To display the year and date, press SNOOZE/
automatically after a preset duration.
DATE/SLEEP OFF once for the date and within
2 seconds press it again for the year. The date
1
Press SLEEP.
or year will appear in the display for a few
The radio turns on. It will go off after the
seconds and then the display returns to the
preset duration. You can set the sleep timer
current time.
to 90, 60, 30, or 15 minutes. When you press
When SNOOZE/DATE/SLEEP OFF is pressed
SLEEP repeatedly, the display changes as
while the SNOOZE function is operating, the
follows.
year and date will not appear in the display.
• To set the current time rapidly, hold down the
OFF (current time)
+ or – button.
• To set the current time from zero seconds,
release CLOCK with the time signal at step 5.
The radio will play for the duration you set,
and then shut off.
To change the display to the
daylight saving time (summer time)
• To turn off the radio before the preset time,
indication
press SNOOZE/DATE/SLEEP OFF.
Press D.S.T./SUMMER T.
"
" is displayed and the time indication
To Use Both Sleep Timer
changes to summer time.
and Alarm
To cancel the summer time indication, press
D.S.T./SUMMER T. again.
You can fall asleep to the radio sound and be
awakened by the radio or buzzer alarm at the
preset time.
1
Playing the Radio
Set the alarm. (See "Setting the
Alarm".)
1
Press RADIO ON to turn on the radio.
2
Set the sleep timer. (See "Setting the
2
Set BAND to FM or AM.
Sleep Timer".)
3
Use TUNE to tune into the desired
station.
4
Adjust volume using VOL.
Troubleshooting
• To turn off the radio, press RADIO OFF.
• To improve reception
Should any problem occur with the unit, make
FM: Extend the FM wire antenna fully to
the following simple checks to determine
increase FM reception sensitivity.
whether or not servicing is required.
AM:Rotate the unit horizontally for optimum
If the problem persists, consult the nearest Sony
dealer.
reception. A ferrite bar antenna is built in
to the unit.
The radio or buzzer alarm does not sound at
the preset alarm time.
• Has the desired radio and/or buzzer alarm
mode been activated with the ALARM dial
Setting the Alarm
("A" and/or "B" indication shown in the
display)?
You can set the radio and buzzer alarms at the
preset time. Before setting the alarm, be sure to
The module does not respond to the control
set the clock (See "Setting the Clock").
of the Dream Machine.
• Be sure the Dream Machine and module are set
1
Hold down ALARM•RADIO A or
to the same ID code.
• Be sure the power switch for the light is turned
ALARM•BUZZER B until a short beep
on.
sounds.
The "A" or "B" indication and the hour will
Lights turn on or off by themselves.
flash in the display.
• Interference from a neighbor's HOME
2
Press either TIME SET + or – until the
SECURITY LIGHT CONTROL SYSTEM Dream
Machine. Change your system's ID code.
desired hour appears in the display.
3
Press ALARM•RADIO A or
ALARM•BUZZER B to set the minutes.
The minutes will flash in the display.
4
Press either TIME SET + or – until the
desired minutes appear in the display.
5
Press ALARM•RADIO A or
ALARM•BUZZER B.
Two short beeps sound to indicate successful
presetting.
6
Turn ALARM dial to the left side from
OFF to set the desired alarm mode.
At the preset alarm time, the radio or buzzer
sounds for 60 minutes or until turned off.
Note
A beep will sound each time you change the
ALARM dial setting.
90(min)
On
15
30
60
Advertisement
