Page 1
PROJECTION TV RECEIVER Chassis : P58A(N) Model : HCN559WX/XAA HCN5529WX/XAA HCN529WX/XAA PROJECTION TV RECEIVER C O N T E N T S Specifications Alignment and Adjustments Exploded View and Parts List Electric Parts List PCB Diagrams Schematic Diagrams...
VIDEO ADJUST 2 VIDEO ADJUST 3 VIDEO ADJUST 4 VIDEO ADJUST 5 VIDEO ADJUST 6 VERSION INFORMATION RESET 4. Service Mode Control Keys MAIN MENU MENU DISPLAY Select item by moving cursor Decrease or increase the adjustment values Samsung Electronics...
Alignment and Adjustments 2-2 Factory Data DVI connection item is corresponded to DVI application model. (HCN559W/HCN5529W) 2-2-1 Defection Samsung Electronics...
Page 7
Alignment and Adjustments 2-2-2 Video Adjust 1 Samsung Electronics...
Page 8
Alignment and Adjustments 2-2-3 Video Adjust 2 Samsung Electronics...
Page 9
Alignment and Adjustments 2-2-4 Video Adjust 3 Samsung Electronics...
Page 10
Alignment and Adjustments 2-2-5 Video Adjust 4 Samsung Electronics...
Page 11
Alignment and Adjustments 2-2-6 Video Adjust 5 Samsung Electronics...
Page 12
SUB CONTRAST R 0 ~ 255 0 ~ 255 0 x361[7 :0] SUB CONTRAST G Contrast Control 0 ~ 255 0 ~ 255 0 x362[7 :0] SUB CONTRAST B 0 x363[7 :0] 0 ~ 255 0 ~ 255 Samsung Electronics...
Alignment and Adjustments 2-3 Screen Change (When adjusting I C Bus Geometric items) V SIZE V SHIFT V LINEARITY V - S - CORRECTION PIN PHASE H SIZE PIN AMP H SHIFT V BOW V ANGLE Samsung Electronics...
Page 15
Examine these points together. following sequence. 1. Use a digital multimeter. 2. Connect the digital multimeter to the JIG pin (DZ482S) terminals 3. Adjust VR (RR402S) so that the voltage becomes 2.25V. Examine these points together Fig. 2-1 Crosshatch Pattern. Samsung Electronics 2-11...
Page 16
(approximately 1~3 mm area) within a 3-block grid around the horizontal center-line. If the color aberration is irregular, adjust the lens as shown in the diagram below. (Accurate alignment of Green is important for overall color quality.) 2-12 Samsung Electronics...
Page 17
13. Adjust the Focus-pack VR for fine focusing. 14. Press the button on the remote control, and the mode changes to the Convergence Adjustment mode. 15. Press the button on the remote control to return to normal viewing. Samsung Electronics 2-13...
Page 18
Alignment and Adjustments 2-6 Convergence-Jig 2-6-1 HCN479W X 1045, Y 588 (X:396=12*2+ 31*12, Y:48 8=40*2+68*6) 31.67mm 81.81mm 31.67mm 48.20mm 81.93mm 48.20mm 2-6-2 HCN559W/5529W X 1225, Y 686 (X:396=12*2+ 31*12, Y:48 8=40*2+68*6) 37.12mm 95.90mm 37.12mm 56.23mm 95.59mm 56.23mm 2-14 Samsung Electronics...
Page 19
Alignment and Adjustments 2-6-3 HCN659W X 1442, Y 838 (X:396 =1 2*2 +31*12, Y: 488=40*2+68*6) 43.70mm 112 .88mm 43.70mm 68.69mm 116 .77mm 68.69mm 2-6-4 HCN529W X 1153, Y 649 (X:396=12*2+ 31*12, Y:48 8=40*2+68*6) 34.94mm 90.26mm 34.94mm 53.20mm 90.43mm 53.20mm Samsung Electronics 2-15...
Page 20
Alignment and Adjustments 2-7 Remote Control Key Functions in Convergence Mode 2-16 Samsung Electronics...
Press to switch the cursor direction horizontally or vertically. 12. SAVE BUTTON After the Convergence Adjustments are completed, press to save data. 13 EXIT BUTTON After the Convergence adjustments are completed, press to exit to TV mode. Samsung Electronics 2-17...
Page 22
After pressing the ANTENNA button, use the Channel Up/Down and Volume +/- buttons to create a tilt to the Convergence Pattern. Note : Use the following two buttons only when they are indispensable. 21. Beam aligment Adjustment Pattern achieve Button 2-18 Samsung Electronics...
If OSD displayed as shown in figure below, press the key to exit. Then, redo step 3 to enter the Convergence Mode. After entering the Convergence Mode, Stand by for about five seconds before doing the adjustments. Samsung Electronics 2-19...
Page 24
Press to move the cursor right or down. 5. The key moves the cursor horizontally or vertically. When the key is pressed once again, the cursor moves horizontally. 6. . The key moves the cursor right, and the key moves the cursor left. 2-20 Samsung Electronics...
Page 25
Channel and Volume keys (Up/Down)to make big adjustments. 9. After the green convergence adjustments are completed, press the key to save the data. 10. Superimpose the Red and Green colors by pessing the and the keys. Samsung Electronics 2-21...
Page 26
B-Mute, and (3) the key for B- select 13. To adjust BLUE, redo steps 5~7, 13. 14. If any color is not properly adjusted when displaying the red, blue and green colors, readjust the color. 2-22 Samsung Electronics...
Page 27
When auto Convergence is complete, the data is automatically saved and the convergence pattern revets. Convergence must be adjusted and saved correctly before Perfect Focus can be performed. Otherwise, a “No Sense Data” error message will appear. Samsung Electronics 2-23...
Page 28
I Changes when applying Almighty-Cg, Module (How to extract the basic Cg Data) Inch Model Name Data Screen Display 47" CN479W 5- 473 52" HCN529W 5- 521 HCN559W 55" 5- 553 HCN5529W 65" HCN659W 5- 653 2-24 Samsung Electronics...