Service Call Errors - Canon iPF6100 Service Manual

E196-4040
E196-4041
E196-4042
E196-4045
E196-404C
E196-404D
E196-404E
E198-401C
E198-401D
E198-401E
E199-404B
E602-401A
E602-401B

8.4.3 Service Call Errors

iPF6300 / iPF6350 / iPF6300S
*Codes correspond to the numbers shown on the DISPLAY in the service mode.
Code
E141-4046 Number of recovery rotations reaching
50,000 or more
E144-4047 Number of carrriage scan operation is full Replace the tube unit, and then clear the parts counter in the service mode.
E144-4048 Printhead ink filling failure
E146-4001 Waste ink recovery count error
E161-403E Abnormal temperature rise in left printhead Replace the left printhead.
E161-403F Abnormal temperature rise in right
printhead
E194-404A Non-discharging nozzle count error
E196-4040 Checksum error (when execute the
firmware update)
E196-4041 Flash memory erase error (when execute
the firmware update)
E196-4042 Flash memory write error (when execute
the firmware update)
E196-4043 Memory error (when execute the firmware
update)
E196-4044 Firmware size error (when execute the
firmware update)
E196-4045 EEPROM read/write error (controller part) Replace the main controller PCB.
E196-4049 Firmware data error (when execute the
firmware update)
E196-404C Serial number mismatch between main
controller PCB and maintenance cartridge
ROM PCB.
E196-404D Machine ID mismatch between main
controller PCB and maintenance cartridge
ROM PCB.
E196-404E EEPROM read/write error (engine part)
E198-401C RTC error
E198-401D RTC low battery error
E198-401E RTC clock stop
E199-404B Temperature/humidity sensor connector
out of position
E602-401A HDD read/write error (HDD failure)
E602-401B HDD connection error
E602-405A HDD size error
Code* Description
Checksum error
Flash memory erase error
Flash memory write error
EEPROM write error
Serial number mismatch between boards
Machine ID mismatch between boards
EEPROM read error
RTC error
RTC low battery error
RTC clock stop
Temperature/humidity sensor board
connector out of position
HDD failure
HDD connection error
Description
Replace the main controller PCB.
Replace the main controller PCB.
Replace the main controller PCB.
Replace the main controller PCB.
Execute PCB replacement mode or replace the main
controller PCB.
Replace the main controller PCB.
Replace the main controller PCB.
Replace the lithium battery or replace the main controller
PCB.
Replace the lithium battery or replace the main controller
PCB.
Replace the lithium battery or replace the main controller
PCB.
Check the temperature/humidity sensor board connector
or replace the board.
Replace the HDD unit.
Check the HDD connector/Replace the HDD unit.
T-8-10
Replace the purge unit, and then clear the parts counter in the service mode.
Replace the printhead.
Replace the platen duct or mist fan or mist filter or suction fan, and then clear the parts
counter in the service mode.
(Confirm the parts reached to the exchange value by the service mode or PRINT INF.)
Replace the right printhead.
Replace the head management sensor unit, and then clear the parts counter in the service
mode.
Execute firmware update or replace the main controller PCB.
Execute firmware update or replace the main controller PCB.
Execute firmware update or replace the main controller PCB.
Execute firmware update or replace the main controller PCB.
Execute firmware update or replace the main controller PCB.
Execute firmware update or replace the main controller PCB.
Execute PCB replacement mode or replace the main controller PCB.
Execute PCB replacement mode or replace the main controller PCB.
Replace the main controller PCB.
Replace the lithium battery or replace the main controller PCB.
Replace the lithium battery or replace the main controller PCB.
Replace the lithium battery or replace the main controller PCB.
Check the temperature/humidity sensor connector or replace the sensor.
Replace the HDD unit.
Check the HDD connector or replace the HDD.
Replace the HDD unit.
Action
Action
Chapter 8
0024-9332
8-41