Page 1
MONITOR USER’S MANUAL V810 MANUEL D’UTILISATION EasyMenu with EasyMenu is HITACHI’s On Screen Display function for easy operation. READ INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your color monitor.
Limited Warranty For USA Customers Only Hitachi America, Ltd. (HAL) warrants our Hitachi color monitor to be free from defects in material and workmanship for 36 months from the date you purchased it from your authorized HAL dealer. In the event of a defect during this 36 months period, HAL will, at its option, repair or replace the monitor at no charge except as set forth below.
Page 3
REPLACEMENT, AS DESCRIBED ABOVE. UNDER NO CIRCUMSTANCES WILL HAL BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING ANY LOST SAVINGS, LOST PROFITS, OR ANY OTHER DAMAGES CAUSED BY THE USE OF THIS MONITOR OR INABILITY TO USE IT, EVEN IF THE DEALER OR HITACHI AMERICA HAS BEEN ADVISED...
CONTENTS FEATURES ....................1 CAUTIONS ....................2 INSTALLATION..................... 6 STANDARD SETTINGS ................. 8 OPERATION....................9 POWER SAVING SYSTEM................16 PLUG & PLAY .................... 16 SPECIFICATIONS ..................17 FEATURES The following features are provided by the Colour Monitor. Sharpest Focus Highest Contrast Flat screen CRT with anti-glare, dynamic focus circuit, dark glass, and an INVAR shadow mask gives the sharpest focus and highest contrast to minimize eye fatigue.
CAUTIONS NEVER REMOVE REAR COVER The rear cover MUST be removed only by authorized service personnel. This colour monitor contains high voltage components. THE RECEPTACLE SHOULD BE CLOSE TO THE MONITOR AND EASILY ACCESSIBLE ! INSTALL UNIT SUITABLE ENVIRONMENT DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard. This unit is designed used...
CAUTION 240V operation only This equipment relies on the protective devices in the building installation for short-circuit and over- current protection. Refer to the following table for the suitable number and location of the protective devices which should be provided in the building installation. Informative examples of protective devices in single - phase equipment or sub - assemblies Protection...
Page 7
FCC (Federal Communications Commission) STATEMENT WARNING WARNING : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 8
FOR THE CUSTOMERS IN THE U.K. THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
INSTALLATION Install the monitor in the following way, taking care to maintain safety. Front Cover Rear Cover CRT Surface Signal Input Connector Power Switch Slot (for optional Control Switches Module “DUB-01A)” Tilt & Swivel Base AC Inlet FRONT VIEW REAR VIEW 1.
Page 10
Use a signal cable with the D-Sub Mini 15-pin Connector. Pin No. Input 1 Input 2 Red Video Red Video Green Video Green Video (Sync. optional) (Sync. optional) Blue Video Blue Video No Pin No Pin No connection No connection Red Ground Red Ground Green Ground...
STANDARD SETTINGS Microprocessor-based preset functions can store 26 sets of geometry settings including the standard settings. The following industrial standard settings have been pre-programmed by the factory. Video Mode Name Horizontal (with Resolution and Video Mode Frequency Vertical Frequency) 640 × 400 - 70 Hz 31.47 kHz 640 ×...
OPERATION Control Switches Select Switch Adjust Switch Input Switch Page 10 “DEGAUSSING” Page 9~13 “ADJUSTMENT” Page 9 “POWER ON/OFF” POWER ON/OFF Press the Power switch, to switch the power ON or OFF. When power is ON, the power LED lights. INPUT This monitor has two input terminals, INPUT 1 and INPUT 2.
Page 13
DEGAUSSING Press the switch “ ”, to degauss manually. DEGAUSS Use this function only when you see colour impurities on the screen after turning ON the monitor. Remember, the monitor is automatically degaussed during initial power Wait for about 10 minutes before repeating the function. ADJUSTMENT Press the select switch of the item you want to adjust.
Page 14
ADJUSTMENT (Continue) Adjust Switch Select Item Switch Function moves position right. H. Position moves position left. expands horizontally. H. Size shrinks horizontally. moves position V. Position moves position down. expands vertically. V. Size shrinks vertically. rotates clockwise. Rotation rotates counter clockwise.
Page 15
ADJUSTMENT (Continue) Adjust Switch Select Item Switch Function changes the colour to the next mode. Colour Select No.1:9300K No.2:6500K No.3:5000K No.4:USER (if available) changes the colour to the previous mode. No.4:USER available) No.3:5000K No.2:6500K No.1:9300K makes the Red stronger. When the Red reaches the upper limit, it makes the simultaneously.
Page 16
ADJUSTMENT (Continue) Adjust Switch Select Item Switch Function operates the horizontal moire changing H. Moire circuit. Reduction simultaneously. stops the horizontal moire changing circuit. makes the operation of the horizontal moire changing circuit stronger. makes the operation of the horizontal moire changing circuit weaker.
Page 17
STORE You can store your settings automatically when the EasyMenu is disappeared. Item Storing Condition Restoring Condition H.Position One setting is allowed for each video mode. When the monitor H.Size detects the same video You can store maximum 26 sets of geometry V.Position mode.
SIGNAL CHECK To refer to the input signal condition, press any switch (Select Switch or Adjust Switch). The horizontal frequency and vertical frequency will be indicated. Precision frequency, ± Horizontal approximately ± 2 Hz Vertical approximately Sample of “EasyMenu” AUTOMATIC SIGNAL CHECK When the monitor has detected the change of the signal input condition, the monitor will indicate the condition automatically, as follows.
POWER SAVING SYSTEM ® This monitor complies with VESA and E power saving requirements. NERGY The power saving system works only when used with VESA DPMS compliant PC’s and/or graphic controllers. When to switch the power OFF during the monitor is in OFF mode, sometimes LED flashing continues a few seconds.
SPECIFICATIONS 21 inch picture tube, 0.22 mm horizontal dot pitch (0.21 horizontal mask pitch), Invar shadow mask, Black matrix, Short persistence phosphors, New Anti-Reflection coat. Video : 0.70 Vp-p, Analogue Input Signal Sync. : Separate H/V, level Composite H/V, level Sync.
Page 21
Technical Support : 1 - 800 - 536 - 6721 World Wide Web Home page : http://www.hitachidisplays.com In Canada : 1 - 800 - HITACHI or 905 - 821 - 4545 World Wide Web Home page : http://www.hitachi.ca All Rights Reserved...