Page 2
Service Guide Version and Revision Version Date Revision History TPV Model Name Apr.-01-08 Initial release E198M2NBWAZEN...
Page 3
Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
Page 4
DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines. Warning: (For FCC Certified Models) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 5
Precautions Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.
Table Of Contents Monitor Features ……………………………………… General Specifications ……………………………………… LCD TV Description ……………………………………… Precautions And Notices ……………………………………… D-SUB PIN Distribution ……………………………………… Chapter 1 Factory Preset Display Modes ……………………………………… LCD TV Panel Specification ……………………………………… Panel Features ……………………………………… General Specifications ……………………………………… Mechanical Specifications ………………………………………...
LCD TV Description The LCD TV will contain a main board (include audio), an I/O board, a switching power board, a function keyboard (include an IR Board) and an Ear phone board. The main board and power board will house the flat panel to control logic I2C bus, DDC, brightness control logic for LCD panel, DC-DC conversion to supply the appropriate power to the whole board and transmitting TTL level signals into LCD Module to drive the LCD display circuit.
D-SUB PIN Distribution This procedure gives you instructions for installing and using the LCD TV display. (1) Position the display on the desired operation and plug the power cord into a convenient AC outlet. Three-wire power cord must be shielded and is provided as a safety precaution as it connects the chassis and cabinet to the electrical conduct ground.
LCD TV Panel Specification M190A1-L0A is a 19” wide TFT Liquid Crystal Display module with 4 CCFL Backlight unit and 30 pins 2ch-LVDS interface. This module supports 1440 x 900 WXGA+ mode and can display 16.7M colors. The inverter module for Backlight is not built in. Panel Features -Super wide viewing angle - High contrast ratio...
Chapter 3 Remote Control & OSD Operating instructions Using the Remote Control 5 e (Empowering Technology) Press to activate Acer Empowering Technology. See page 25. 6 MENU Press to open or close the Menu. 7 Back Press to back to previous Menu.
Page 16
Teletext 1 Color buttons (R/G/Y/B) Operates corresponding button on the teletext page. 2 INDEX Press to go to the index page. 3 SUBTITLE Press to view subtitles on the screen. 4 REVEAL Press to reveal hidden telext information. 5 SUBPAGE Press to access the teletext’s subpages directly.
Logo When the monitor is power on, the LOGO will be showed in the center, and disappear slowly. How To Optimize The DOS-Mode Plug And Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
Chapter 4 Machine Disassembly This chapter contains step-by-step procedures on how to disassemble the monitor for maintenance. Disassembly Procedure Disassemble The Base 1. Put the monitor on a clean soft cloth with panel facing to the table. (Fig 1) (Fig 1) 2.
Page 27
(Fig 3 ) Disassemble the back cover 1. Remove four screws to remove back cover. (Fig 4) ( Fig 4) Remove the main board, power Board, IR board and key board. 1. Remove the rear cover, then the main board ,power board, ir board and key board show as below. (Fig 5-6) 2.
Page 28
Key board (Fig 6) Disassemble the speaker. Remove the four screws marked in red to remove the speakers. (Fig 7) ( Fig 8 ) Remove the main frame Remove the four screws marked in red to remove the main frame.
Page 29
( Fig 9 ) (Fig 10) Disassemble the IR board (Fig 11) Disassemble the front panel...
Chapter 5 Trouble Shooting No picture (LED orange) No picture Check key board/IR board Change key board/IR board Check 24V power supply Check IC971 power supply circuit Check main board Standby power supply Change U902 Check U401 Change U401 Check I C communication Check I C bus...
Abnormal display Reset source Check the source Check signal filter circuit Replace the filter or resistance RF signal Check TV system setup Check input Check LVDS cable Check Tuner Replace LVDS cable Check panel Replace panel Replace Tuner...
Page 33
No sound Reset source Check the source Check if mute Check TV Reset TV system Check input signal TV SIF system Check U401 Check TU1 Change TU1 Change U401 Check U601 Change U601 Check speaker Change speaker...
Page 34
No Power (No LED indicator) Check CN902 pin10,11 = 12V Check AC line volt 110V or 220V Check AC input Check the voltage of C905 (+) Check bridge rectified circuit and F901 circuit Check start voltage for the pin8 of IC901 Check R904, R905 and Change IC901 Check the auxiliary voltage is bigger than 10V and smaller than 20V...
Page 35
W / LED, No Backlight Check R803=12V Check adapter or MB Check ON/OFF Check Interface board Check IC801 Change Check IC801 PIN 15 have the output of square wave at short time Change IC801 Check the input of Q80 5, Q806 Change Q805, Q806,D801,D802,D803,Q804 Check the output of PT801, PT802 Change PT801, PT802...
Page 36
Key Board OSD is unstable or not working Is Key Pad Board connecting normally? Connect Key Pad Board Replace Button Switch Is Button Switch normally? Is Key Pad Board Normally? Replace Key Pad Board Check Main Board...
Chapter 6 White-Balance, Luminance Adjustment Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment. First adjust PC mode and then adjust AV mode, before started adjust white balance, please setting the Chroma-7120 MEM. Channel 1 to Cold color, MEM. MEM. channel 3 to standard color, MEM. and MEM. channel 5 to warm color, ( our cold parameter is x = 300 ±...
Page 38
1. Set the Contrast of OSD function to 80 and Adjust Brightness to chroma-7120 Y>350 cd/m2 2. Switch the chroma-7120 to RGB-mode (with press “MODE” button) 3. Switch the MEM. channel to Channel 03 (with up or down arrow on chroma-7120) 4.
Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
Chapter 9 Schematic Diagram Main Board Inverter Audio AMP 3W X 2 PANEL POWER TDA8932BTW POWER 3.3V,2.5V,1.8V,1.2V,1.1V BOARD LVDS PCMCIA ZENTEL Common Interface Controller SCALER MT5335AKU 5V,3.3V A3S56D40ETP DDR MT8295 3.3V,2.5V,1.2V,1.1V 3.3V,1.8V 2.5V MPEG-1 layer I/II decoding,Audio ADC,Audio DAC 3D surround processing with virtual surround Automatic volume control,Audio I/F,USB2.0 2-D Graphic,De-interlace,VADCx4,HDMI In I/F Digital TV Demodulator,Analog TV IF Demodulator...
Power Source Vol- Vol+ Menu T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer Size 絬 隔 瓜 絪 腹 715T TPV MODEL TV2268W-AED Key Component MT5335 Key Pad PCB NAME 715T28981-B 称爹 <称爹>...
Page 69
C104 C102 0.1uF 10uF/10V 100pF/50V T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer TV Size 絬 隔 瓜 絪 腹 <絬隔瓜絪腹> TPV MODEL TV2268W-AED Key Component MT5335 IR/LED PCB NAME 715T2982-D 称爹 <称爹>...