Kenwood TK-260G Service Manual page 11

8. Self Programming Mode (TK-270G only)
Write mode for frequency data and signalling etc. Mainly
used by the person maintaining the user equipment.
8.1 Self programming mode setting
Remove D17 from the TX-RX unit (Figure 3) (K models
only). Hold down the [LAMP]+[ ] switches and turn the
power switch on.
When the self programming mode is entered, [SELF]
appears on the display. The mode changes automatically
to Model Select Mode and "PORTABLE" is displayed in
about one second.
Note :
This mode (self programming mode) cannot be set when it
has been disabled with the FPU.
Flow Chart
Radio type
Radio Band & Channel Type
Frequency Version
[3]
Self programming mode
Channel set mode
Note :
IF the radio type of TK-270G was temporally set to "Mobile"
for the cloning purposes, "UNPROG" is displayed (at User
Mode) when the TK-270G is turned on.
In this case, please set the radio type back to "Portable" at
Model Select Mode menu.
8-2. Channel Setting Mode
This is a mode for making channel settings with the panel
keys without using the FPU.
Pressing [MON] when "SELF" is displayed, sets Channel
Setting Mode.
Select an item set using [3] then change the selection with
the encoder.
The data displayed using [2] is stored in the memory and
then proceeds to the next item. Pressing [3] proceeds to
the next item without storing it in the memory.
Press [MON] to set the display to "SELF" and return to reset
(default) status.
Downloaded from www.Manualslib.com
Portable
[2]
VHF 8CH
[2]
VHF F1
[2]
[MON] [LAMP]
Function set mode
manuals search engine
REALIGNMENT
Mobile
[CH]
[CH]
VHF 128CH UHF 8CH
[CH] [CH]
[CH]
VHF F2 UHF F1
[CH] [CH]
No. Function Choices Display
Select
Channel
Select
Group
1 RX frequency Step 2.5kHz-1MHz STP_250 Display when an item is selected
2 Rx Signaling OFF
TK-260G/270G
X57-587X
Compoent Side
D17
Fig. 3
UHF 128CH
[CH]
UHF F3 UHF F4
[CH] [CH]
Cannot be
Cannot be
set when
set when
Mobile is
Portable is
select
select
1-128 _1-_1._ [3] : Group selection/
_1-128._ Channel selection change
1-128 _1.-_1_
128.-_1_
STP_1000 or when a step is changed
(about 0.5 seconds)
•
[ ] Step change
VHF : 2.5, 5.0,6.25,7.5kHz,1MHz,Step
Blank ———— [LAMP] : Freq On/Blank switching
100.0000- R.100.0000 The rightmost dot indicates
550.0000MHz 50Hz digit (On=5; Off=0).
———— [LAMP] : Off/QT/DQT switching
•
QT 67.0-250.3Hz QT_67.0_ [ ] : Mode switching
°
(EIA Mode) QT_250.3_ [ ] : Normal/Inverse
QT 67.0-250.3Hz QT_67.0*
(0.1Hz Step Mode) QT_250.3*
DQT 000-777 (Normal) DQT000N*
(1 Step Mode) DQT777N*
DQT 023-754 (Normal) DQT023N
(Standard Table Mode) DQT754N
DQT 000-777 (Inverse) DQT000I*
(1 Step Mode) DQT777I*
DQT 023-754 (Inverse) DQT023I
(Standard Table Mode) DQT754I
Remarks
switching
11