Page 2
IMPORTANT SERVICE GUIDE ◆ MODE SWITCH (PROGRAM SWITCH) ASSEMBLY POINT 1) When installing the ass’y deck on the Main PCB, be sure to align the assembly point of mode switch. ASSEMBLY POINT MAIN PCB Fig. 1 ◆ HOW TO EJECT THE CASSETTE TAPE (If the tape is stuck in the unit) 1) Turn the Gear Worm Œ...
Page 3
Metal Part cal return path to the chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the out- ohmmeter let and repeat the test. See Fig. 1-1. Fig. 1-2 Insulation Resistance Test Samsung Electronics...
Page 4
(5) antenna wiring. Always inspect in all areas tinuously and new instructions are issued whenev- for pinched, out-of-place, or frayed wiring, Do not er appropriate. change spacing between a component and the printed-circuit board. Check the AC power cord for damage. Samsung Electronics...
Components identi- fied by shading, by( ) or by ( ) in the circuit dia- gram are important for safety or for the characteris- tics of the unit. Always replace them with the exact replacement components. Samsung Electronics...
Page 6
(6) Do not remove a replacement ESD device from its protective package until immediately before your are ready to install it.(Most replacement ESD devices are packaged with leads electrically short- ed together by conductive foam, aluminum foil or comparable conductive materials). Samsung Electronics...
Page 7
◆ Be sure to put on a wrist strap grounded to the sheet. ◆ Be sure to lay a conductive sheet made of copper etc. Which is grounded to the table. Samsung Electronics...
Page 8
3) Make solder land 2 points short on Pick-up. (See Fig. 1-4) 4) Disassemble the Pick-up. Note : If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged. SOLDER LAND 2 POINTS SHORT PICK-UP ASS'Y Fig. 1-4 Samsung Electronics...
- When the adjustment is completed, be sure to turn the power off. 2-1-1(a) Location of adjustment button of remote control STANDBY/ON OPEN/CLOSE X-Point (Tracking Center) Adjustment ; NVRAM Option Setting ; Head Switching Adjustment ; Fig. 2-1 Samsung Electronics...
Page 10
Alignment and Adjustments 2-1-1(b) TEST location for adjustment mode setting TEST (SW706) BUTTON Fig. 2-2 VCR Main PCB (Top View) Samsung Electronics...
” button is pressed, the selected number is changescolor. ; See Fig. 2-4) 5) Press the “ENTER” button of remote control again to store the option number. 6) Turn the Power off. PLEASE WAIT CNG : OK SAVE : RETURN Fig. 2-3 Fig. 2-4 Samsung Electronics...
Alignment and Adjustments 2-2 DVD Adjustment 2-2-1 Location of Test Point Fig. 2-5 Location of test Point (DVD Main PCB - Top Side) Samsung Electronics...
Page 14
<Table 2-2> Test Disc Adjustment Spec. Test Point Adjustment Location TDV-533 “ENV” Ass’y Deck - Top Side Chapter 14 Flat Waveform (DVD Main PCB - Top Side) (See Fig. 2-6) (See Fig. 2-5) Fig. 2-6 Ass’y Deck (Top Side) Samsung Electronics...
Page 15
If you cannot obtain a Flat waveform, then the unit is defective. Note : The Deck must be in a horizontal position. Use both “A” and “B” screws to adjust. Typical Waveform before Adjustment Waveform after Correct Adjustment Fig. 2-7 Envelope Waveform Samsung Electronics...
Fig. 2-8 Location of Tape Transport Adjustment PINCH ROLLER FE HEAD CYLINDER ASS'Y GUIDE ROLLER "S" GUIDE ROLLER "T" POST TENSION #8 GUIDE POST #9 GUIDE POST #3 GUIDE POST MAIN BASE ACE HEAD CAPSTAN SHAFT Fig. 2-9 Tape Travel Diagram Samsung Electronics...
Page 17
HEIGHT ADJUST X-POSITION ADJUSTING SLIT SCREW (B) SCREW (D) AZIMUTH ADJUST X-POSITION LOCKING Fig. 2-10 Location of ACE Head Adjustment Screw AUDIO HEAD VIDEO HEAD 0 ~ 0 .25 mm CONTROL HEAD Fig. 2-11 ACE Head Height Adjustment Samsung Electronics...
Page 18
Fig. 2-12 Tape Guide Check c. AUDIO AZIMUTH ADJUSTMENT 1) Load alignment tape (Mono scope) and playback the 7KHz signal. 2) Connect channel-1 scope probe to audio output. 3) Adjust screw (B) to achieve maximum audio level. (See Fig. 2-10) 2-10 Samsung Electronics...
Page 19
5) Insert the (-) driver into the X-Point adjustment hole and adjust it so that envelope waveform is maximum. Test point : TP2 (Audio Output) TP3 (Envelope) TP4 (H’D S/W -Trigger) TP5 (Control Pulse) AUDIO OUTPUT ENVELOPE HEAD SWITCHING CONTROL PULSE Fig. 2-13 Location of Test point (Main PCB-Top View) Samsung Electronics 2-11...
Page 20
5) If the section B in Fig. 2-15 does not meet the specification, adjust the guide roller T up or down. a b c d c,b,d/a Fig. 2-14 Envelope Waveform Adjustment H'D SWITCHING PULSE ENVELOPE Fig. 2-15 Adjustment Points 2-12 Samsung Electronics...
Page 21
) driver to obtain a flat video RF envelope as shown in Fig. 2-16. IDEAL ENVELOPE S HEIGHT TOO HIGH S HEIGHT TOO LOW T HEIGHT TOO HIGH T HEIGHT TOO LOW GUIDE ROLLER S GUIDE ROLLER T Fig. 2-16 Guide Roller S, T Height Adjustment Samsung Electronics 2-13...
Page 22
2) If excessive tape wrinkle is observed, perform the following adjustments in Playback mode : ◆ Tape wrinkle at the guide roller S, T section : Linearity adjustment. ◆ Tape wrinkle at tape guide flange : ACE head assembly coarse adjustment. 2-14 Samsung Electronics...
Page 23
4) Transportation of accurate driving force is done by gears. (Gear Center Ass’y) Note : If the spec. does not meet the followings specifications, replace the holder clutch ass’y and then recheck. <Table 2-4> MODE TORQUE g/cm GAUGE 42 ± 11 Cassette Torquemeter 145 ± 30 Cassette Torquemeter Samsung Electronics 2-15...
Page 24
Alignment and Adjustments MEMO 2-16 Samsung Electronics...
Page 25
3-4 DVD Mechanical Parts - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-8 Notice You can search for the updated part code through ITSELF web site. URL; http://itself.sec.samsung.co.kr Samsung Electronics...
0403-001211 DIODE-ZENER;MTZJ12B,11.44-12.03V,500MW,D R610 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R611 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM SYSTEM CONTROL/SERVO PARTS R613 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608 BACK-UP 1HOUR Only C601 2203-002398 C-CER,CHIP;22nF,10%,50V,X7R,TP,1608 R614 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM C602 2401-002095 C-AL;47uF,20%,25V,GP,TP,6.3x5,5 R615 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 36
2203-000257 C-CER,CHIP;10nF,10%,50V,X7R,TP,1608 L302 2701-000002 INDUCTOR-AXIAL;100uH,10%,4298 C329 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- L303 2701-000002 INDUCTOR-AXIAL;100uH,10%,4298 C330 2203-000975 C-CER,CHIP;47nF,10%,25V,X7R,TP,1608,- L304 3301-000297 BEAD-AXIAL;25ohm,3.6x1.2x5.7mm,,TP,,, C331 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- L370 2701-000113 INDUCTOR-AXIAL;100uH,5%,2534 C332 2202-002055 C-CERAMIC,MLC-AXIAL;47nF,+80-20%,50V,Y5V L3A01 2702-000120 INDUCTOR-RADIAL;15000uH,5%,6.2x7.4mm Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 37
2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM C525 2401-001249 C-AL;4.7uF,20%,35V,GP,TP,4x5,2.5 R3A28 2007-000079 R-CHIP;1.8Kohm,5%,1/10W,TP,1608 C526 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5 R3A50 2001-000800 R-CARBON;5.1KOHM,5%,1/8W,AA,TP,1.8X3.2M C527 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5S,TP, R3A51 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608 C529 2401-001250 C-AL;4.7uF,20%,35V,GP,TP,4x5,5 R3A60 2001-000605 R-CARBON;3.6KOHM,5%,1/8W,AA,TP,1.8X3.2M C530 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 38
2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608 Not used CIS C4N09 2401-000408 C-AL;10uF,20%,16V,GP,TP,3.5x5,2.5 R6P10 2007-000075 R-CHIP;220ohm,5%,1/10W,TP,1608 C4N10 2401-000408 C-AL;10uF,20%,16V,GP,TP,3.5x5,2.5 R6P12 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M C4N11 2401-002186 C-AL;3.3UF,20%,50V,GP,BK,4X5,2.5 R6P13 2007-000097 R-CHIP;47Kohm,5%,1/10W,TP,1608 C4N12 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- R6P14 2007-000123 R-CHIP;1.5Kohm,5%,1/10W,TP,1608 Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 39
R803 2007-000079 R-CHIP;1.8Kohm,5%,1/10W,TP,1608 D705 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35, R804 2001-000563 R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM Not used CANAL+ DT701 AK07-00004A LED DISPLAY;BCD-9027A,(BRIGHT),DVD-V3000 R805 2007-000643 R-CHIP;270ohm,5%,1/10W,TP,1608 IC701 1003-001561 IC-LED DRIVER;PT6961,SOP,32P,300MIL,-,40 R806 2007-000643 R-CHIP;270ohm,5%,1/10W,TP,1608 L701 2701-000002 INDUCTOR-AXIAL;100uH,10%,4298 Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 40
3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3 CNL2 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3 CNR1 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 0504-000128 TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP CNR10 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608 AQ10 0501-000341 TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT- CNR11 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608 AQ11 0501-000341 TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT- CNR2 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 41
2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608 RC15 2203-000975 C-CER,CHIP;47nF,10%,25V,X7R,TP,1608,- FR12 2007-000124 R-CHIP;2.2Kohm,5%,1/10W,TP,1608 RC16 2203-000257 C-CER,CHIP;10nF,10%,50V,X7R,TP,1608 FR13 2007-000124 R-CHIP;2.2Kohm,5%,1/10W,TP,1608 RC17 2203-000560 C-CER,CHIP;220nF,+80-20%,25V,Y5V,TP,1608 FR14 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608 RC18 2203-000236 C-CER,CHIP;0.1NF,5%,50V,C0G,TP,1608 FR15 2007-000655 R-CHIP;27Kohm,5%,1/10W,TP,1608 RC19 2203-000560 C-CER,CHIP;220nF,+80-20%,25V,Y5V,TP,1608 Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 42
2007-000124 R-CHIP;2.2Kohm,5%,1/10W,TP,1608 2007-000077 R-CHIP;470ohm,5%,1/10W,TP,1608 SR13 2007-000092 R-CHIP;15Kohm,5%,1/10W,TP,1608 2007-000312 R-CHIP;10ohm,5%,1/4W,TP,3216 SR14 2007-000092 R-CHIP;15Kohm,5%,1/10W,TP,1608 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- SR15 2007-000091 R-CHIP;12Kohm,5%,1/10W,TP,1608 SC11 2203-000560 C-CER,CHIP;220nF,+80-20%,25V,Y5V,TP,1608 SR16 2007-000655 R-CHIP;27Kohm,5%,1/10W,TP,1608 SC13 2203-001634 C-CER,CHIP;33nF,10%,50V,X7R,TP,1608,1.6m SR17 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608 Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 43
3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3 0403-001083 DIODE-ZENER;UDZ9.1B,9.1V,8.85-9.23V,200m ZL15 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- ZL195 3301-000314 BEAD-SMD;120ohm,1.6x0.8x0.8mm,150mA,,,, ZC10 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- ZL196 2703-000398 INDUCTOR-SMD;10uH,10%,3225 ZC101 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- ZL197 2703-000398 INDUCTOR-SMD;10uH,10%,3225 ZC102 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3 Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 44
R-CHIP;4.7Kohm,5%,1/10W,TP,1608 R1SF05 2001-000527 R-CARBON;22OHM,5%,1/8W,AA,TP,1.8X3.2MM ZR80 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 R1SF06 2004-000459 R-METAL;2.2Kohm,1%,1/8W,AA,TP,1.8x3.2m ZR81 2007-000076 R-CHIP;330ohm,5%,1/10W,TP,1608 R1SF07 2003-000105 R-METAL OXIDE;0.33ohm,5%,2W,AD,TP,6x16mm ZR82 2007-001167 R-CHIP;75ohm,5%,1/10W,TP,1608 R1SQ11 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608 R1SR01 2001-000548 R-CARBON;270KOHM,5%,1/8W,AA,TP,1.8X3.2M 4-10 Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 45
C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- HR109 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 HC166 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- HR110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 HC17 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- HR118 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 HC172 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- HR119 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 HC175 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,- HR122 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 Samsung Electronics 4-11 This Document can not be used without Samsung’s authorization...
Page 46
3404-001182 SWITCH-TACT;DC12V,50MA,100GF,6.0X6.0X5.0 SW710 3404-001182 SWITCH-TACT;DC12V,50MA,100GF,6.0X6.0X5.0 SW711 3404-001182 SWITCH-TACT;DC12V,50MA,100GF,6.0X6.0X5.0 SW712 3404-001182 SWITCH-TACT;DC12V,50MA,100GF,6.0X6.0X5.0 SW714 3404-001182 SWITCH-TACT;DC12V,50MA,100GF,6.0X6.0X5.0 SW715 3404-001182 SWITCH-TACT;DC12V,50MA,100GF,6.0X6.0X5.0 ASSY PCB-HOUSING;DP-9,EXINO S.N.A HCN1 AH39-00266B CONNECT WIRE;-,#26,-,-,-,WHT/BLK,-,-,-,- HSW1 3409-001138 SWITCH-DETECTOR;5V DC,1A,DPST,30GF,- 4-12 Samsung Electronics This Document can not be used without Samsung’s authorization...
DVD & CD Processor & Digital Level Shifter VCR Main Micom EPROM SIC2 4M EDO RAM IC701 ZIC3 (PT6961) (MBM29LV800BA) LED Drive IMB Flash Memory Front A/V Jack STEREO (DT701) Samsung Electronics This Document can not be used without Samsung’s authorization...
Page 48
Block Diagram MEMO Samsung Electronics This Document can not be used without Samsung’s authorization...