Table of Contents
Advertisement
Descale
The appliance must be descaled regularly in order for it
to continue operating correctly.
There are several steps in the descaling programme. All
steps must be completed in full. Only after this is the
appliance ready for use again.
If you touch the ÿ On/Off button during the
Note:
descaling programme, the process is interrupted and
the appliance switches off. Once the appliance has
been switched back on again, it must first be rinsed
twice in order to remove any remaining descaling
solution from the appliance. The appliance is locked for
other applications until the second rinsing cycle is
complete.
Descale (approx. 30 minutes), then empty the
■
evaporator dish and refill the water tank
First rinsing cycle (20 seconds), then empty the
■
evaporator dish
Second rinsing cycle (20 seconds), then remove the
■
remaining water
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only five more steam-assisted operations are
possible, or fewer, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Start
Caution!
Damage to the appliance: Use only liquid descalers
■
that are recommended by us for the descaling
programme. The time the product needs to work
during descaling depends on the type of descaler
used. Other descalers may damage the appliance.
Descaler order no. 311 680
Descaling solution: Do not allow any descaling
■
solution or descaler to come into contact with the
control panel or other delicate surfaces. This will
damage the surfaces. If this does happen, remove
the descaling solution immediately with water.
Mix 300 ml water with 60 ml liquid descaler to make
1.
a descaling solution.
Remove the water tank and fill with descaling
2.
solution.
Fully insert the water tank filled with the descaling
3.
solution.
Close the appliance door.
4.
Touch the ÿ On/Off button.
5.
Touch the V Descale operating mode.
6.
The duration of the descaling programme is
displayed. It cannot be changed.
Press the l Start/Stop button to start.
7.
The appliance is descaled. The time counts down on
the display. As soon as the descaling programme
has finished, an audible signal sounds.
First rinsing cycle
Use the cleaning sponge provided to remove the
1.
descaling solution from the evaporator dish.
Remove the water tank, rinse thoroughly, fill with
2.
water and reinsert.
Close the appliance door.
3.
Press the l Start/Stop button to start.
4.
The appliance rinses. The first rinsing cycle ends
after around 20 seconds.
Open the appliance door.
5.
Thoroughly rinse out the cleaning sponge with water.
6.
Use the cleaning sponge to remove the remaining
7.
water in the evaporator dish.
Proceed with the second rinsing cycle.
8.
Second rinsing cycle
Remove the water tank, rinse thoroughly, fill with
1.
water and reinsert.
Close the appliance door.
2.
Press the l Start/Stop button to start.
3.
The appliance rinses. The second rinsing cycle ends
after around 20 seconds.
Use the cleaning sponge to remove the remaining
4.
water in the evaporator dish.
Use the cleaning sponge to wipe out the cooking
5.
compartment and then dry it with a soft cloth.
Switch off the appliance.
6.
Descaling is complete and the appliance is ready for
use again.
Descaling the evaporator dish only
You can also use "Descale" if you do not wish to
descale the whole appliance, but only the evaporator
dish in the cooking compartment.
The only difference is as follows:
Mix 100 ml water with 20 ml liquid descaler to make
1.
a descaling solution.
Completely fill the evaporator dish with descaling
2.
solution.
Fill the water tank with water only.
3.
Start "Descale" as described.
4.
You can also descale the evaporator dish manually.
Cleaning
en
21
Advertisement
Table of Contents
