. Set Mechanical Exploded view……………………………………….7-1 . Revision List…………………………………………………..…..8-1 CLASS 1 Copyright 2006 Philips Consumer Electronics B.V. Eindhoven, The Netherlands LASER PRODUCT All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.
http://www.jdwxzlw.com/?fromuser=华盛维修 Mechanical and Dismantling Instructions Dismantling Instruction The following guidelines show how to dismantle the Step2: If it is necessary to dismantle Loader or Front Panel, It recorder. should be remove the front door assembly first. (Figure 2) Step1: Remove the 8pcs of screw around the Top Cover. If the tray can’t open in normal way, you can make it through And remove it (Figure 1) the instruction as figure 3 &...
http://www.jdwxzlw.com/?fromuser=华盛维修 Mechanical and Dismantling Instructions Dismantling Instruction Uplift the bottom of loader The door will fall off automatically Figure 4 Remove the screws on Figure 3 both side of loader Push it gently, and the tray will flick out automatically Figure 5 家电维修资料网,免费下载各种维修资料...
http://www.jdwxzlw.com/?fromuser=华盛维修 Mechanical and Dismantling Instructions Dismantling Instruction Step4: Dismantling Front Panel: disconnect the 9 Step3: Dismantling Loader, First, disconnect the 2 connectors ,1 GND cable aiming in the figure then Release connectors aiming in the figure, and then remove the 4 the snaps on the both sides of Front Panel and the relative screws at both sides of the loader, (Figure 6) screws on the cabinet, finally gently pull the panel out from...
Page 6
http://www.jdwxzlw.com/?fromuser=华盛维修 Mechanical and Dismantling Instructions Dismantling Instruction Step5: Dismantling MPEG Board, first disconnect the Step6: Dismantling Tuner Board, first disconnect the 2 4 connectors ,then remove the relative screws connectors ,then remove the relative screws(Figure10) (Figure9) CON 14 CON 15 CON 13 CON 12 GND Cable...
Page 7
http://www.jdwxzlw.com/?fromuser=华盛维修 Mechanical and Dismantling Instructions Dismantling Instruction Step7: Dismantling AV Board, first disconnect the 3 connectors, and then remove the relative screws, (Figure 11) CON 18 CON 19 CON 20 Figure 11 Step9: Dismantling Power Board, first Step8: Remove the 3 screws on the back of the disconnect the connector, then remove the relative cabinet, then dismantling the IO Board.
The software version and other information are display on File System: ISO9660 the TV screen as follows: File Name: DMN8600.CUB (For DVDR3375/93) Build: XXX XXX XXX XXX XXX C ware: XXXX Note: It is required capital letter for the Label name Nav: XXXX (Software version of decoder) &...
http://www.jdwxzlw.com/?fromuser=华盛维修 Trouble Shooting Chart No display on VFD, and buttons do not work No display on VFD, and buttons do not work Check every supply voltage on main board is Refer to Power supply board part normal Check-24V+12V, VCC Fix the connection JP1 on front board (+5v) voltage on the and CN1 on power board power and front board...
Page 10
http://www.jdwxzlw.com/?fromuser=华盛维修 Trouble Shooting Chart No digital audio output No digital audio output Check the FB8 (digital audio) Fix the connection JP8 on AV board on the OP board is normal. and JP2 on OP board Check R130 Check / Replace R131、C133. (digital audio) on the AV board is normal.
Page 11
http://www.jdwxzlw.com/?fromuser=华盛维修 Trouble Shooting Chart Remote control does not work Remote control does not work Check whether keys on Replace U2 on the power board the front board work or not. Check the front board whether P1 of U4 has Replace U4 on the power board signal when pressing key on the remote Replace U1.
Page 12
http://www.jdwxzlw.com/?fromuser=华盛维修 Trouble Shooting Chart Can’t read disc or can’t open the disk door Can’t read disc or can’t open the disk door Check whether Check the connection of the 4PIN cable DVD loader running is from CN5 on the Power Board. normal Check 40pin cable from Fix the connection the 40pin cable...
Page 13
http://www.jdwxzlw.com/?fromuser=华盛维修 Trouble Shooting Chart No VFD display No VFD display Check whether the Fix the connection power board voltage +12V/+5V on the CN1& front board JP1 front board is normal Check whether Check DC12V to AC 3V switch circuit voltage between F1&VFD F2 is AC3V Check...
Page 14
http://www.jdwxzlw.com/?fromuser=华盛维修 Trouble Shooting Chart Fan don’t work Fan don’t work Check on Power board Check R9 on Power board whether P1 of CN3 is +12v Check cable Replace the cable connection fan to Power board CN3 Replace Fan 家电维修资料网,免费下载各种维修资料...
Page 15
http://www.jdwxzlw.com/?fromuser=华盛维修 Trouble Shooting Chart Can’t read disc or can’t open the disk door Can’t read disc or can’t open the disk door Check whether Check the connection of the 4PIN cable DVD loader running is from CN5 on the Power Board. normal Check 40pin cable from Fix the connection the 40pin cable...
Page 16
DVDR3375 Block Diagram 1EEE1394 TUNER AUDIO IN 1 WM8776 AUDIO IN 2 POWER AUDIO ADC AUDIO IN 3 1394 TUNER VIDEO DECODER DMN8602 CVBS CVBS S/PDIF LOAD ATAPI BUFFER AUDIO LCH WM8776 FORNT FLASH SDRAM AUDIO PANEL KEY EEROM IR &...
Page 27
6-10 6-10 DVDR3375 Main Board Electrical Diagram : TERM AT E5 & DDR & VREF/VT The VTT side of the terminaton resistors should be placed TERMINATION AT E5.1 on a wide VTT island on the surface layer. The island is...