IMPORTANT SAFETY NOTICE There are special parts used in Panasonic LCD Projectors which are important for safety. These parts are shaded on the schematic diagram. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire, or other hazards.
TABLE OF CONTENTS COVER PAGE ■ 1. Safety Precautions 2. Specifications SECTION 1 <Service Information> ■ 1. The name of each part 2. OSD Menu Navigation 3. Extend mode (EXT OPTION menu) 4. External Control 5. Notification for service operation 6.
1. Safety Precautions 1.1. General Guidelines - For continued safety, no modification of any circuit must be attempted. - Unplug the power cord from the power outlet before disassembling this projector. - Use correctly the supplied power cord and must ground it. - It is advisable to use an isolation transformer in the AC power line before the service.
2. Specifications *1 : Measurement, measuring conditions and method of notation all comply with ISO21118 international standards. *2 : For details of video signals that can be projected using this projector, refer to “List of compatible signals” of Operating Instructions.
Page 6
*1 : HD/SYNC, and VD terminals do not accept tri-level sync signals. *2 : Average value. Weight varies for each product..
SECTION 1 < Service Information > PT-AE7000U / AE7000EA / AE7000EH Model No. PT-AT5000E CONTENTS 1. The name of each part ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ INF-2 1.1. Projector body 1.2. Control panel 1.3. Rear terminals 1.4. Remote control 2. OSD Menu Navigation ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ INF-4 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 3.Extend mode (EXT OPTION menu) INF-6 3.
3. Extend mode (EXT OPTION menu) This projector has extend mode "EXT OPTION" menu in addition to standard on-screen menus. This mode has Self-Check function, Test Pattern and other functions for Service. 3. 1. Procedure to open / close "EXT OPTION" menu. 1.
Page 13
Rotation check of Exhaust fan and Power fan (Displays "NG" when Fan is abnormal condition) (17)- * When detected abnormal temperature around the air intake port / air exhaust port / LCD block, TEMP indicator turned on. If arriving at the critical temperature, the power supply will shut down automatically (thermal shutdown) and the indicator will flash.
4. External Controls of SERIAL Connection The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer which is connected to this connecter. 4.
4. 5. Basic format The transmission from Personal Computer starts with STX, Command, Parameter and EXT are sent in order. Parameter is added depending on the control. : Command Parameter Start byte(02h) 3 bytes 1 byte 1byte - 4 bytes End (03h) ・The projector can not receive any command for 10 seconds after the lamp is switched on.
5. Notification for service operation 5. 1. Before service operation 5. 1. 1. LCD panel 1. The display unit of this projector comprises three LCD panels. Although an LCD panel is a product of high precision technology, some of the pixels on the projected image may be missing or constantly lit. Please note that this is not a malfunction.
5. 2. Service 5. 2. 1. Supporting Methods The basic service policy is shown below. Service method Applied parts ・ Analyses block (* Specified components are replaced) ・ Optical Block (with projection lens) *Projection lens can not be separated from optical block. Block replacement P.C.Board replacement ・...
Page 19
5. 3. 2. Replacement procedure for lamp unit 1. Confirm that the lamp unit is cooled down completely. (More than 1 hour has passed after main power is off.) 2. Open the top cover in the direction of the arrow. 3.
Page 20
5. 3. 4. Air filter unit maintenance 1. If too much dust accumulates in the air filter the internal temperature of the projector cannot be maintained at the normal level. 2. Confirmation message is displayed on the screen, and at the same time <TEMP> illuminates red. The power is cut off automatically after a while.
6. Troubleshooting 6. 1. Summary of shut down system When the abnormality of the lamp and the abnormality of the fan occurred, possess a shut down function to make a standby state for safety promptly. Monitor LED indication Shut down Detection Presumed Factor OSD Warning Indication Power fuse...
Page 22
SECTION 2 <Disassembly Procedures> PT-AE7000U / AE7000EA / AE7000EH Model No. PT-AT5000E CONTENTS 1. Parts Location ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ DIS-2 1. 1. Electrical Parts Location (P.C.Board) 1. 2. Electrical Parts Location (Fan) 2. Disassembly Instructions ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ DIS-3 2. 1. Flowchart for Disassembly 2. 2. Removal of Top Cover 2.
1. Parts Location 1. 1. Electrical Parts Location (P.C.Board) Function summary Function summary Board Name Board Name Image processing system Temp sensor (Exhaust) / Microcomputer Control Panel Temp sensor (Air flow) Indicator LED Ballast power / Ballast control 3D-IR transmitter Power supply (DC-DC) Iris posistion sensor AC Inlet...
2. Disassembly Instructions 2. 1. Flowchart for Disassembly * Before Disassembly the projector, turn off the POWER switch and disconnect the power plug from the wall outlet. * To assemble, reverse the disassembly procedures. * When tore off sticky tapes, please use a new thing without reusing it on the occasion of assembling. * Description of the illustration may be different from the real.
2. 2. Removal of Top Cover 1. Remove the Top panel. Top panel 1) Hold the top cover as shown in the diagram. 2) While pushing the arm in the direction of the arrow (inside projector), pull out from the groove. * Attaching the top panel 1) Hold the top cover as shown in the diagram.
2. 4. Removal of Optical Block / Analysis Block 1. Remove the A-P.C.Board block according to the steps 1 through 2 in the section 2.3. "Removal of A-P.C.Board". 2. Loosen the 2 screws and remove the Lamp unit. 3. Unscrew the 1 screw and remove the V-P.C.Board. 4.
2. 5. Removal of L-P.C.Board 1. Remove the Optical block according to the steps 1 through 6 in the section 2.4. "Removal of Optical Block / Analysis Block". 2. Unscrew the 2 screws and remove the LED cover. LED cover Optical block 3.
2. 7. Removal of PBS Array / Iris Unit 1. Remove the Analysis block according to the section 2.4. "Removal of Optical Block / Analysis Block". 2. Unscrew the 5 screws and remove the Analysis case (upper). * Can be removal of PBS Array. * The incidence polarizer is installed in the Analysis case (upper).
Page 29
4. Unscrew the 1 screw and remove the Lamp socket. Lamp socket 5. Unscrew the 5 screws and remove the Ballast block. * Remove the P2 connector. Ballast block 6. Unscrew the 2 screws and remove the P-P.C.Board. P-P.C.Board 7. Unscrew the 2 screws and while pressing to shut each hook of the 2 resinous stands, remove the B-P.C.Board. B-P.C.Board Note : 1) The direction the Power Fan install.
2. 9. Removal of K1-P.C.board / K2-P.C.Board 1. Remove the A-P.C.Board earth metal according to the steps 1 through 5 in the section 2.4. "Removal of Optical Block / Analysis Block". 2. Unscrew the 4 screws and remove the Optical Block and Analysis Block. Optical Block + Analysis Block 3.
2.10. Remonal of M2-P.C.Board 1. Remove the Top Cover according to the section 2.2 "Removal of Top Cover". 2. Unscrew the 1 screw and remove the V-P.C.Board. Front cover 3. Unscrew the 3 screws and remove the Front cover. V-P.C.Board 4.
Page 32
SECTION 3 < Adjustments > PT-AE7000U / AE7000EA / AE7000EH Model No. PT-AT5000E CONTENTS 1. Adjustment items and procedure ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ADJ-2 1. 1. Flicker Adjustment 1. 2. Data Transfer 1. 3. Model Information Setup 1. 4. Model Information Setup 1. 5. Clog Sensor calibration 2.
1. Adjustment item and a procedure When the following components in this projector are replaced, adjustments are required. Adjust each item according to the table below. Adjustment Items Replaced parts Remarks 1. 1. Flicker Adjustment OPTICAL BLOCK / A-P.C.Board Save data to a PC before A-P.C.B exchange and 1.
Page 34
5. 1) Click the [ Reception ] button of Micom Data. 2) Select the save place and click the [ Save ] button. 3) When the progress bar reaches the right-side end, the save of data is completion. 4) Save the Gamma Data, Uniformity Data and the Color Management Data in the same procedure of 1-3. ①...
1. 3. Model Information Setup 1. 3. 1. Required equipments 1. PC : Use it as adjustment use. 2. Communication cable : D-sub 9pin (male/emale RS-232C straight) 3. Software : [Service ORCA10.exe]Adjustment software is downloaded from the projector service homepage. 1.
Page 36
1. 4. Serial Number Setup 1. 4. 1. Required equipments 1. PC : Use it as adjustment use. 2. Communication cable : D-sub 9pin (male/emale RS-232C straight) 3. Software : [Service ORCA10.exe]Adjustment software is downloaded from the projector service homepage. 1.
1. 5. Clog Sensor Calibration Clog sensor circuit is calibrated. * This operation should be done with the main body is completely assembled and set on the floor and the adjuster legs are set in the main body. (A state of Disassembly, cannot correct it.) * Confirm that there is no heating equipments, flow out of air conditioner, obstacles for air intake and exhausting for the projector.
2. Microprocessor update procedure * The update is done by SERIAL terminal connection. * During update, prevent PC from going into stand-by or shut down. 2. 1. Update by the SERIAL terminal connection 2. 1. 1. Equipment to be used 1.
Page 39
6. Click the [ SOFT UPDATE ] button. 7. Click the [OK] button and start update. 8. Click the [ OK ] button after completion message is displayed. * Reboot Projector, and please confirm whether the version of the Microprocessor Software is updated definitely, with sub menu "...
Page 40
SECTION 4 Important Safety Notice < Schematic Diagram > Components identified by the intemational symbol have special characteristics important for safety. When replacing any of these components, use only the manufacturer's specified ones. PT-AE7000U / AE7000EA / AE7000EH Model No. ■Notes 1.
ADJUSTER LEG TXFKK01REGZ LENS CAP ASSY TBMV249 OPERATION SHEET 50-1 TKKX5109 LENS CAP STRAP 5 TEEC5512 EXHAUST DUCT 1 TBMA413 PANASONIC BADGE TEEC5513 EXHAUST DUCT 2 TBMA414 3D LOGO BADGE TEEC5515 INTAKE DUCT TQFX260 MODEL NO. LABEL TKPB60001 SHIFT COVER TQFX267 MODEL NO.
Page 56
Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks TXJ/V1RWDZ V1-A9 CABLE TXJ/S1RWDZ S1-A8 CABLE CIRCUIT BOARD A TXANP99RWDZ (RTL) TXJ/M2RWDZ M3-A13 CABLE TXFEW01RWDZ M1-A12 CABLE TNPA5458 CIRCUIT BOARD S (RTL) ...
Page 57
Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks C1084 F1G1C104A077 C.CAPACITOR CH 16V 0.1U C1232 F1H1A225A051 C.CAPACITOR CH 10V 2.2U C1085 C.CAPACITOR CH 10V 10U C1233 C.CAPACITOR CH 50V 22P F1J1A106A043 F1G1H220A565 C1086 F1G1C104A077 C.CAPACITOR CH 16V 0.1U...
Page 58
Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks C1603-06 EEFCX0D221R E.CAPACITOR CH 2.5V 220U C1765 F1G1C104A077 C.CAPACITOR CH 16V 0.1U C1607 E.CAPACITOR CH 4V 220U C1766 C.CAPACITOR CH 50V 220P F2G0G2210009 F1G1H221A571 C1608-11 F1J0J2260004 C.CAPACITOR CH 6.3V 22U...
Page 59
Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks C1895 F1H1E104A030 C.CAPACITOR CH 25V 0.1U FL1000-02 J0HABC000011 EMI FILTER C1896 F1G1C104A077 C.CAPACITOR CH 16V 0.1U FL1003 J0HAYY000046 EMI FILTER C1897 F1H1E104A030 C.CAPACITOR CH 25V 0.1U C1898 F2G1E3300010 E.CAPACITOR CH 25V 33U...
Page 60
Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks L1047,48 R1002-07 J0JYC0000024 EMI FILTER ERJ6ENF75R0 M 75 OHM, 1/10W L1049,50 J0JBC0000086 EMI FILTER R1008,09 ERJ3GEYJ101 M 100 OHM,J,1/16W L1051 J0JYC0000024 EMI FILTER R1010-15 ERJ6ENF75R0 M 75 OHM, 1/10W L1052...
Page 61
Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks R1244 R1366 ERJ2GEJ101 M 100 OHM, 0.063W ERJ3GEYJ392 M 3.9K OHM,J,1/16W R1245,46 ERJ2GE0R00 M 0 OHM, 0.063W R1367 ERJ3GEYJ470 M 47 OHM,J,1/16W R1247 ERJ3GEY0R00 M 0 OHM,J,1/16W R1368 ERJ3GEYJ100...
Page 62
Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks R1535 R1751 ERJ2GE0R00 M 0 OHM, 0.063W ERJ2GEJ223 M 22K OHM, 0.063W R1536 ERJ2GEJ472 M4.7K OHM, 0.063W R1752 ERJ3GEY0R00 M 0 OHM,J,1/16W R1537 ERJ3GEY0R00 M 0 OHM,J,1/16W R1753 ERJ2GEJ472...
Page 63
Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks R1952 C2001 ERJ3GEY0R00 M 0 OHM,J,1/16W F1J1A106A097 CAPACITOR R1953 ERJ3EKF2201 M 2.2K OHM, 1/16W C2002 F1G1C104A077 C.CAPACITOR CH 16V 0.1U R1954 ERJ3GEY0R00 M 0 OHM,J,1/16W R1955 ERJ3EKF1002 M 10KOHM, 1/16W...
Page 64
Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks MISCELLANEOUS TXAWC01VKJ8 AC INLET U TXJ/K1VKG7 K1-KP CABLE TNPA5470 CIRCUIT BOARD K2 F9101 FUSE K5E802BZA004 SW9101 K0AAKA000014 AC SWICH SPL-15...