6. Perform the following precautions against unwanted radiation and rise in internal temperature. • Always return the internal wiring to the original styling. • Attach parts (Gascket, Ferrite Core, Ground, Rear Cover, Shield Case etc.) surely after disassembly. PDP-433CMX...
PRODUCT SAFETY NOTICE Many electrical and mechanical parts in PIONEER set have special Leakage Current Cold Check safety related characteristics. These are often not evident from With the AC plug removed from an AC power source, place a visual inspection nor the protection afforded by them necessarily jumper across the two plug prongs.
Page 4
Assy Front SCAN (B) Assy X CONNECTOR (A) Assy X DRIVE Assy X CONNECTOR (B) Assy SW POWER SUPPLY Module Power Switch (S1) AC Inlet with Filter Power Cord Fig.1 Charged Section and High Voltage Generating Point (Rear View) PDP-433CMX...
Page 5
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. PDP-433CMX...
............................. 7.1 DIAGNOSIS ..................... 7.1.1 CONFIGURATION OF THE PC BOARD ............7.1.2 DIAGNOSIS FOR SHUTDOWN AND POWER-DOWN BY LED ..............7.1.3 AUTOMATIC BACKUP OF DIGITAL VIDEO ASSY DATA ........................... 7.1.4 DISASSEMBLY ........................... 7.2 IC INFORMATION ............................8. PANEL FACILITIES PDP-433CMX...
• For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING PDP-433CMX Only PDP-433MXE PDP-433CMX Only...
Page 9
Remote Control Unit AXD1459 Ferrite Core See Contrast table (2) Warranty Card Contens Label See Contrast table (2) (2) CONTRAST TABLE PDP-433CMX/LUCB and PDP-433MXE/YVLDK are constructed the same except for the following : Part No. Mark Symbol and Description PDP-433CMX PDP-433MXE Remarks...
Page 27
ADX2738 Screw AMZ30P060FZK • • • • • Solder Warning Label See Contrast table (2) (2) CONTRAST TABLE PDP-433CMX/LUCB and PDP-433MXE/YVLDK are constructed the same except for the following : Part No. Mark Symbol and Description PDP-433CMX PDP-433MXE Remarks LUCB...
Screw ABZ30P050FZK Screw VMZ30P060FZK Energy Star Label AAX2856 Display Label See Contrast table (2) (2) CONTRAST TABLE PDP-433CMX/LUCB and PDP-433MXE/YVLDK are constructed the same except for the following : Part No. Mark Symbol and Description PDP-433CMX PDP-433MXE Remarks LUCB YVLDK...
See Contrast table (2) Rear Corner Label AAX2862 Korean Label See Contrast table (2) Bottom View (2) CONTRAST TABLE PDP-433CMX/LUCB and PDP-433MXE/YVLDK are constructed the same except for the following : Part No. Mark Symbol and Description Remarks PDP-433CMX PDP-433MXE...
Page 31
: Module exclusive use PW : Common use of public use and module ∗ In case of this unit, the parts that "W" is marked removes. PDP Service Assy 433 (AWU1069) Circuit Board Spacer Circuit Board Spacer (AEC1872) (AEC1872) PDP-433CMX...
Page 49
Clamp Mode : AUTO Clamp Mode : AUTO Clamp Mode : AUTO Clamp Mode : AUTO Color Mode : COLOR MODE 1 Color Mode : COLOR MODE 1 Color Mode : COLOR MODE 1 Color Mode : COLOR MODE 1 PDP-433CMX...
Page 50
K5315 (HD_SEL) and k 5317 (HD _ 30) synchronize with K5316 (VD_SEL). K5316 (VD_SEL) K5317 (HD_30) K5314 (DE_SEL) K5315 (HD_SEL) Magnified K5316 (VD_SEL) section of No. 32. Frequency of 2 times of K5314 K5316 (VD_SEL) (DE_SEL), K5315 (HD_SEL) and K5317 (HD_30) in the 1125i indication. K5316 (VD_SEL) K5317 (HD_30) PDP-433CMX...
MUTING key (AA49) Double audio (AA1E) OFFSET mode • Adjustment of the signal input side. MUTING key (AA49) VIDEO OPTION mode SCREEN SIZE (AAD3-AF3C) MUTING key (AA49) INITIALIZE mode Full auto zoom (AAD3-AF36) or P. ZOOM (AAD3-AF22) PDP-433CMX...
Page 69
• AXD1459 (PDP-503CMX/PDP-433CMX) POWER POWER MENU SCREEN DISPLAY CALL SIZE SCREEN SIZE FULL AUTO FULL AUTO ZOOM ZOOM DISPLAY CALL SURROUND MUTE MODE MUTE SOUND AUDIO VOLUME SOUND MENU VOLUME AV MEMORY SURROUND MODE AV SELECT AUDIO • AXD1432 • AXD1673...
Page 70
• While there is no input, The partial setting, or while incompatible PC signals are input, settings that are not dependent on the signal mode can be performed. (For the MASK setting, see "MASK 1," and "MASK 2.") The setting items that are dependent on the input signal mode are grayed on the display and cannot be changed. PDP-433CMX...
R SIDE MASK LEV R SIDE MASK LEV VOP-M LEV-1 0 to 255 IC30 G SIDE MASK LEV G SIDE MASK LEV VOP-M LEV-2 0 to 255 B SIDE MASK LEV B SIDE MASK LEV VOP-M LEV-3 0 to 255 PDP-433CMX...
Page 72
VIDEO OPTION), and add the OFFSET value of the selected setting. The addition of the COLOR TEMP OFFSET value is not needed in Integrator mode or in Service Factory mode (except for COLOR TEMP adjustment mode,) because the unit operates with the COLOR TEMP 3 settings. PDP-433CMX...
: OFFSET value (adjustment value) * Adjustment value is REFERENCE value + OFFSET value. 3. When VIDEO OPTION is selected : No display When INITIALIZE is selected : Selected setting. (No display for an item having the lower layer.) PDP-433CMX...
Page 74
• When this mode is entered, the VERSION display (the function called by pressing the "1" key) is displayed first. • When any of the above keys are pressed, the corresponding operation is executed. Note: The VERSION display is the default display for Service Factory mode. PDP-433CMX...
Page 75
Up to eight power-downs are displayed. If the number of power-downs becomes more than 8, the latest data are added, and the oldest data are cleared. Display details at PD INFORMATION Display PD Point Display PD Point X-DRV X-DRIVE ADRES ADDRESS junction X-DDC X-DC/DC CONVERTER ADR-K ADDRESS resonance Y-DRV Y-DRIVE POWER Power supply Y-DDC Y-DC/DC CONVERTER DC-DC DC/DC CONVERTER (DIGITAL) PDP-433CMX...
Page 77
• When a slot is not inserted, or when a slot manufactured by other vendor is inserted, the SLOT item cannot be selected. (The display is not skipped during item selection.) • Items that cannot be selected are grayed on the display. PDP-433CMX...
Page 78
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "____," and the item indication is grayed. PDP-433CMX...
Page 79
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "____," and the item indication is grayed. PDP-433CMX...
Page 80
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "____," and the item indication is grayed. PDP-433CMX...
Page 81
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "____," and the item indication is grayed. PDP-433CMX...
Page 82
• When a slot is not inserted, or when a slot manufactured by other vendor is inserted, the SLOT item cannot be selected. (The display is not skipped during item selection.) • Items that cannot be selected are grayed on the display. • Selection of each item is impossible when there is no input signal. PDP-433CMX...
Page 83
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "___(___)," and the item indication is grayed. PDP-433CMX...
Page 84
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "___(___)," and the item indication is grayed. PDP-433CMX...
Page 85
• When the input signal mode is not identified, the adjustment value is displayed with "___(___)," and the item indication is grayed. • As the items X-SUS-B, X-SUS-G, Y-SUS-B, Y-SUS-G, V-SUS, and V-OFFSET do not have OFFSET adjustment values, making settings is not allowed. These items are grayed, and the adjustment values are displayed with "___(___)." PDP-433CMX...
Page 86
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "___(___)," and the item indication is grayed. PDP-433CMX...
Page 87
RANGE CHECK AA59 AV SELECT REFERENCE Shifting to various AA43 AV MEMORY adjustment / setting AA1E OFFSET screen AAD3-AF3C SCREEN SIZE VIDEO OPTION AAD3-AF36 FULL AUTO ZOOM INITIALIZE AAD3-AF22 P.ZOOM Shifting to next adjustment AA49 MUTING INITIALIZE / setting screen PDP-433CMX...
Page 88
• COLOR TEMP setting during COLOR TEMP adjustment When Service Factory mode is entered, the setting for COLOR TEMP becomes MIDDLE regardless of the user's setting. During COLOR TEMP adjustment, the unit operates in the selected COLOR TEMP mode. PDP-433CMX...
Page 89
• When this mode is entered, the R SIDE MASK LEVEL display (the function called by pressing the "1" key) is displayed first. • When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. PDP-433CMX...
Page 90
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • During COLOR MODE adjustment, the setting becomes COLOR MODE 2, and the adjusted value will be stored in memory, but the color mode setting will not be stored after adjustment is completed. PDP-433CMX...
Page 91
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • During COLOR TEMP adjustment, the unit operates with the selected COLOR TEMP setting, and the adjusted value will be stored in memory, but the COLOR TEMP setting will return to MIDDLE after adjustment is completed. PDP-433CMX...
Page 92
RANGE CHECK AA59 AV SELECT REFERENCE Shifting to various AA43 AV MEMORY adjustment / setting AA1E OFFSET screen AAD3-AF3C SCREEN SIZE VIDEO OPTION AAD3-AF36 FULL AUTO ZOOM INITIALIZE AAD3-AF22 P.ZOOM Shifting to next adjustment AA49 MUTING INFORMATION / setting screen PDP-433CMX...
Page 93
SET : To register the setting and shift to the confirmation screen for setting changes. U L S S E T N OW D A T A : 1 2 3 4 5 S E T D A T A : 0 9 7 0 0 PDP-433CMX...
Page 94
• To release the mask setting, use "M00" of RS-232C Factory Adjustment mode or "MASK OFF" of Service Factory menu. (The mask setting cannot be released with FULL MASK OFF of the Integrator menu or "FMN" of the RS-232C Factory Adjustment mode.) PDP-433CMX...
Page 95
Note: If PICTURE DEFAULT is executed: 1 All the PICTURE items set on the user menu are reset. 2 The values for PICTURE, WHITE BAL, and SIDE MASK LEVEL of the Integrator menu will become those of current adjustment values of Service Factory mode. PDP-433CMX...
Page 96
For each function that can be controlled by the PC HDTV MODE 1035i Common to all input functions COMPONENT1 750p/1125i/1125p VIDEO INPUT COMPONENT2 525i/525p/625i/625p SUB VOLUME For each input function Common to all units BAUD RATE 4800BPS (Setting/Timer time/Mask time/mask color) TIMER OFF/1/0.0/WHT Common to all input functions PDP-433CMX...
Page 97
Common to all units − − ID NO SET SLOT INPUT VIDEO (RGB) Factory Setting Item INTE MODE UNLOCK MASK1/2 setting Common to all units ACL SW COLOR DET NO CARE RS-232C Setting Item VIDEO MUTE Common to all units 100% display PDP-433CMX...
Page 98
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. Note: During MASK setting, an OSD is not displayed. If another operation is selected, an OSD is displayed for 2 seconds after the MASK signal output is stopped, then the selected FULL MASK display will be displayed again. PDP-433CMX...
Page 99
RANGE CHECK AA59 AV SELECT REFERENCE Shifting to various adjustment / AA43 AV MEMORY setting screen AA1E OFFSET AAD3-AF3C SCREEN SIZE VIDEO OPTION AAD3-AF36 FULL AUTO ZOOM INITIALIZE AAD3-AF22 P.ZOOM AA49 MUTING Shifting to next adjustment / setting screen INFORMATION PDP-433CMX...
3. If you are reusing the collected old PC board as a service part, attach the new IC1204 to the board. DIGITAL VIDEO Assy SW POWER SUPPLY Module Y DRIVE Assy X DRIVE Assy RGB Assy Video Card (PDA-5002) Fig. 1 Configuration of the PC Board (rear side view) PDP-433CMX...
Adjust the TINT so that the height ratio of each stairstep waveform becomes constant. c: Adjust the Level so that the waveform becomes 525 mVp-p. B-Y Level Color-Bar IC7103 CN7401-pin 5 525mVp-p Adjustment (IC7103) (SA100) 525mVp-p Each adjustment value is stored in IC7104. PDP-433CMX...
Page 106
Side mask color / Level Adjustment SIDE MASK LEV. Set the indicated value with the keys on the remote control unit (1, 2 and 3 keys). R SIDE LEVEL : key 1 G SIDE LEVEL : key 2 B SIDE LEVEL : key 3 PDP-433CMX...
Page 107
Green signal measured in step 9. Tolerance: ± 0.05V OFFSET mode: Select RGB 1 mode with the top and bottom keys. AD B HIGH : "8" key Adjust with the right and left keys. PDP-433CMX...
Page 108
Green signal measured in step 9 of video signal. Tolerance: ± 0.05V OFFSET mode: Select RGB 1 mode with the top and bottom keys. AD R HIGH : "6" key Adjust with the right and left keys. PDP-433CMX...
Page 109
TINT : "4" key Reference: Adjustment values when using the Minolta color-difference meter NTSC 20% window-step signal (-3dB) White Balance 80% window-step signal (-3dB) − Flesh Window chroma signal Color − PDP-433CMX...
TxD outputs of data on various SETUP settings − − − − GET ADJUST SLOT TxD outputs of data of picture quality setting of SLOT − − − − GET ADJUST RGB TxD outputs of data of picture quality adjustment (RGB 1) PDP-433CMX...
Page 113
Top and bottom reversing display − − MIRROR MODE XY Top/bottom and right/left reversing display − − VIDEO MUTE NO To turn the video mute of IC30 to OFF − − VIDEO MUTE YES To turn the video mute of IC30 to ON PDP-433CMX...
Page 114
− − VARIABLE OUTPUT To set the audio output to variable − − − 3S Y/C MOTION To set the 3D Y/C setting to MOTION − − − 3D Y/C STILL To set the 3D Y/C setting to STILL PDP-433CMX...
Page 115
3 byte Offset of W/B adjustment value (Offset data) 3 byte (Note 1) Blue (Note 1) : If data are output when the Reference mode is selected, the same data as the reference data are output as the offset data. PDP-433CMX...
Page 116
3 byte Wide /FLASH ROM version 3 byte Display Information Data Model PDP-503CMX/MXE (initial value) PDP-433CMX/MXE Module 50 inches Module 43 inches PDP-503HD PDP-433HD GS2: Outputting data for power down, temperature and condensation information • Data are output according to the transmission order and size in the table below.
Page 117
(Note 1) (Reference data) 3 byte B-Y LEVEL (Offset data) 3 byte (Note 1) (Note 1) : If data are output when Reference mode is selected, the same data as the reference data are output as the offset data. PDP-433CMX...
Page 118
H.POSITION 3 byte V.POSITION 3 byte CLOCK 3 byte (Note 1) PHASE 3 byte (Note 1) V.SIZE 3 byte (Note 1) When the current input signal mode is VIDEO or INPUT 5(DVI), dummy data(*) are output as adjustment data. PDP-433CMX...
Page 119
Hour meter information of the eighth latest PD 7 byte Upper 5byte: HOUR, Lower 2byte: MINUTE (Note 1) See the table below on PD information Data Power Down Point None Y-DRIVE Y-DC/DC CONVERTER X-DC/DC CONVERTER X-DRIVE Power supply ADDRESS junction ADDRESS resonance DC/DC CONVERTER (DIGITAL) PDP-433CMX...
Page 120
(Note 1) See the table below on SD information Table 2: SD contents GET Data Shut Down Point Panel microcomputer communication failure Module IIC communication failure Condensation Temperature abnormality FAN abnormality Module microcomputer communication failure Wide microcomputer communication failure Main IIC communication failure AUDIO failure PDP-433CMX...
Page 121
(Note 1) As for the setting data not related to the current input function/input signal/setting, dummy data are output. (Note 2) If data are output when the Reference mode is selected, the same data as the reference data are output as the offset data. PDP-433CMX...
Page 122
SUB VOLUME (INPUT4) 2 byte 0 to 60 (Note 1) SUB VOLUME (INPUT5) 2 byte 0 to 60 (Note 1) (Note 1) As for the setting data not related to the current input function/input signal/setting, dummy data are output. PDP-433CMX...
Page 123
TEMPERATURE 3 byte A/D input value (Note 2) HOUR METER 5 byte Unit : H 0: Lock release KEY LOCK 1 byte 1: Lock (Note 1) Dummy data (*) are output when a SLOT manufactured by Pioneer is connected. PDP-433CMX...
X CONNECTOR Assy (B) Assy I/O Assy SP OUT L ADR CONNECT C RGB Assy Assy Assy RESONANCE Assy SUB ADDRESS B MX LED Assy Assy ADR CONNECT B Assy BRIDGE D Assy ADR CONNECT A Assy Rear View PDP-433CMX...
Wait another 5 seconds, then recover the unit by setting the MAIN X-DC/DC CONVERTER POWER button to ON. X-DRIVE Power supply Note: After power-down is released, the unit restarts and goes to Standby mode. Address junction Address resonance DIGITAL-DC/DC CONVERTER PDP-433CMX...
Page 126
Block Diagram of the Shutdown Signal System ("STANDBY/ON" LED: Blinking in green) PDP-433CMX...
Page 127
1 byte Seventh latest "SD INFO" 1 byte Shutdown Point OSD Data Panel microcomputer communication failure Module IIC communication failure Condensation Temperature abnormality FAN abnormality Module microcomputer communication failure Wide microcomputer communication failure Main IIC communication failure AUDIO failure PDP-433CMX...
Page 128
T EMP 2 Temperature displayed in "INFORMATION" of the Factory menu T E MP 3 : 0 8 8 TEMP1 (°C) TEMP1 (data) -50 F A N 1 3 5 TEMP2 (°C) TEMP2 (data) /2+5 TEMP3 (°C) TEMP3 (data) /2+5 PDP-433CMX...
Page 129
: The power is shut down as soon as a failure is detected. Possible causes • Disconnection of a connector between the MX AUDIO Assy (A5) and the RGB Assy (R8). • Short-circuiting between + and - of C8615 and C8622. PDP-433CMX...
Page 130
Block Diagram of the Power Down Signal System ("STANDBY/ON" LED: Blinking red) PDP-433CMX...
Page 131
P.D. by 3.3V undervoltage (= overcurrent) 2.5V OVP P.D. by 2.5V overvoltage 2.5V UVP P.D. by 2.5V undervoltage (= overcurrent) Reference OVP : Over Voltage Protect UVP : Under Voltage Protect OCP : Over Current Protect : Power Down PDP-433CMX...
Page 132
Seventh latest "1st PD" point 1 byte Seventh latest "2nd PD" point 1 byte Seventh latest PD time stamp 7 byte Eighth latest "1st PD" point 1 byte Eighth latest "2nd PD" point 1 byte Eighth latest PD time stamp 7 byte PDP-433CMX...
Page 134
Similarly, the switches and the semifixed VRs inside the power- 200V AC). supply module must not be adjusted without a special reason. Setting: For the MXE model only, the switch is set to 200V, and for other models, it is set to 100V. PDP-433CMX...
1 Automatic copying is performed every time the Service Factory mode is entered (regardless of the keyword.) 2 When the power is turned on, keyword checking is performed, then automatic copying is performed if the keyword for the DIGITAL VIDEO Assy (Area B) is "not adjusted," and that for the RGB Assy is "adjusted." PDP-433CMX...
Page 136
After repair, readjustment is required. 2. Except for data for the COLOR and TINT items, data in Area C in the EEPROM of the RGB Assy are assembly-adjustment data. Readjustment is not required when the RGB Assy is replaced with one for service. PDP-433CMX...
SW Power Supply Remove the four screws. Module Remove the SW Power Supply Module. SW Power Supply Module Slit SW Power Supply Module Insert the SW Power Supply Module into the slits of sub frame L and R. Diagnosis PDP-433CMX...
Page 138
DIGITAL VIDEO Assy RGB Base ×2 ×2 ×2 ×2 I/O Assy Terminal Panel CMX DIGITAL VIDEO Assy Remove the connectors and binders, and remove the RGB base with PCB Assys. DIGITAL VIDEO Assy RGB Assy SLOT CONNECTOR Assy RGB Base PDP-433CMX...
Page 139
Front Case Assy 43 (M) Rear Case ×6 Aluminum Materials The hook of the front case assy 43 (M) is fixed with the rear case (M) and the aluminum material, as shown in the illustration. ×6 SCAN (B) Assy PDP-433CMX...
Page 140
(GGD1035). ×2 ×2 Jig Cable SLOT CONNECTOR Assy (GGD1035) RGB Assy ×2 ×2 Video Card X DRIVE Assy Reconnect the video card. (Do not insert it into the slot.) Video Card SLOT CONNECTOR Assy RGB Assy Diagnosis PDP-433CMX...
List of IC SN755860PJ, M30624FGAFP, HD64F2328VF, GAL22V10, M30624FGAFP, PD6358A, PST9246N, FS781BZB, ML6426CS-1, CXA3516R, BA5417, STK795-460 SN755864APZP (SCAN A ASSY : IC6201 - IC6206) SN755864APZP (SCAN B ASSY : IC6001 - IC6006) • Scan IC • Pin Assignment (Top view) PDP-433CMX...
Page 142
The high potential circuit power supply which is common to HVO1 - HVO32 − 41, 42, 78, 79 The high potential circuit power supply which is common to HVO33 - HVO64 29, 33, 43, 47 − It is the insulation electrically 77, 80, 83, 96 PDP-433CMX...
Page 143
Non connection 44 NC 45 OSD_CE Enable for OSD 46 CE CE input for flash writing (pull-up) 47 WU_CE Enable for waide microcomputer 48 FAN_NG NG detection for fan 49 IN5DET Video signal input detection 50 CB_MUTE Combination mute PDP-433CMX...
Page 144
95 TEMP2 A/D input for temperature sensor 2 96 AVSS GND for AD conversion (GND connection) 97 PM_ST Pull-up 98 VREF AD conversion reference voltage 99 AVCC Power supply for AD conversion 100 RXD Serial 3 line data input PDP-433CMX...
Page 145
Vact interrupt input after frame rate conversion DE_W DE interrupt for start line detection of panel link input V VD_W Vertical synchronization interrupts before FRC VACT_IP Histogram acquisition interrupt input FILM_IP Acquisition interrupt input of film information 3.3V power supply Data bus Data bus PDP-433CMX...
Page 146
Reset input from the main unit microcomputer and reset IC Not used Pull-up Not used 3.3V power supply XTAL Connect a ceramic resonator (25MHz) EXTAL 3.3V power supply PHAI System clock output 3.3V power supply SGLB_IP Single input selecting output of IC102 PDP-433CMX...
Page 160
) t i ) t i ) t i ) t i ) t i f i f ) t i r i f ) t i ) t i ) t i ) t r PDP-433CMX...
Page 161
) t i ) t i ) t i ) t i ) t i ) t i ) t i PDP-433CMX...
Page 162
PST9246N (DIGITAL VIDEO ASSY : IC1208) • Reset IC • Pin Assignment (Top View) SOT - 25 (TOP VIEW) • Block Diagram • Pin Function Pin No. Pin name Functions control pin Substrate pin GND pin Reset signal output pin pin/voltage detect pin PDP-433CMX...
Page 163
CMOS/TTL Modulated Clock Frequency Output. The center frequency is the same as the input reference frequency for FS781. Input frequency is multiplied by 2x and 4x for FS782 and FS784 respectively. Power Positive Power Supply. Power Power Supply Ground PDP-433CMX...
Page 164
Internally pulled low. B Unfiltered analog G- or U-channel input for Bank <B>. Sync must be SYNC IN Input for an external H-sync logic provided at SYNC IN pin. signal for filter channels. CMOS level input. Active High. PDP-433CMX...
Page 165
CXA3516R (RGB ASSY : IC4603) • AD + PLL IC • Pin Assignment (Top View) PDP-433CMX...
SET button Press to adjust or enter various settings on the unit. SCREEN SIZE button Press to select the screen size. AUTO SET UP button When using computer signal input, automatically sets the POSITION and CLOCK/PHASE to optimum values. PDP-433CMX...
For connection of components that have RGB or CONTROL IN/OUT (monaural mini jacks) component output jacks such as a personal computer, For connection of PIONEER components that bear the Î mark. Making CONTROL connection enables control DVD player, or external RGB decoder. Make sure that the connection made corresponds to the format of the of the plasma display as a component in a system.
Page 174
AC power source. SPEAKER (L) terminal For connection of an external left speaker. Connect a speaker that has an impedance of 8 -16 Ω. PDP-433CMX...
Press to put the unit in operation or standby mode. DISPLAY button Press to view the unit’s current input and setup mode. POINT ZOOM button Use to select and enlarge one part of the screen. VOLUME (+/–) buttons Use to adjust the volume. PDP-433CMX...
2 Set this unit in the stand. CAUTION Because this unit weighs about 88 lbs 3 oz (about 30 kg) and the lack of depth makes it fairly unstable, please use 2 people or more when packing, carrying or installing. PDP-433CMX...
Page 177
÷ When possible, please install using parts and accessories on a flat, unwarped surface. manufactured by PIONEER. PIONEER will not he held responsible for accident or damage caused by the use of parts and accessories manufactured by other companies.