Page 1
Form No. 3392-160 Rev A Verticutter Reelmaster ® 6000-D Series Cutting Unit Model No. 03877—Serial No. 316000001 and Up *3392-160* A Register at www.Toro.com. Original Instructions (EN)
Setup ................4 1 Inspecting the Verticutter........5 You may contact Toro directly at www.Toro.com for product 2 Installing the Transport Rollers ....... 5 safety and operation training materials, accessory information, 3 Adjusting the Blade Depth ........5 help finding a dealer, or to register your product.
Also, tighten any • To ensure optimum performance and continued safety loose nuts, bolts, and screws to ensure that the verticutters certification of the machine, use only genuine Toro are in safe operating condition. replacement parts and accessories. Replacement parts •...
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Inspect the verticutter. Transport roller Install the transport rollers. – No parts required Adjust the blade depth. – No parts required Adjust the rear grass shield.
Note: Whenever the verticutter has to be tipped to expose the verticutter blades, use the kickstand (supplied with traction unit); refer to Figure Installing the Transport Rollers Parts needed for this procedure: Transport roller Procedure Secure a transport-roller bracket to each side-plate pin with a cotter pin (Figure Figure 2...
Figure 5 1. Rear grass shield 2. Pivot cap screw Figure 4 2. Rotate the grass shield to the desired setting, and 1. Gauge bar (1/4 inch) 2. Adjusting bolt tighten the cap screws (Figure WARNING Note: The verticutter blades must not touch the gauge bars.
2. Move the scraper rods in or out to attain 0.0 to 0.75 mm (0.0 to 0.03 inch) clearance between the scraper and the roller. 3. Ensure that the scraper rod is parallel to the roller and Mounting the Lift Brackets and to the level surface.
Note: Rotate the brackets 10° to the outboard side 2. On lift arms 2 and 3, position the brackets and U-bolts 38 cm (15 inches) behind the center line of the pivot of the machine. knuckle (Figure 4. Tighten all the U-bolt nuts to 52 to 65 N∙m (38 to 48 ft-lb).
3. Secure pivot knuckle to carrier frame with a thrust washer, a flat washer, and a flange-head cap screw (Figure 12). 4. Insert a thrust washer onto the vertical shaft of the pivot knuckle (Figure 12). 5. If removed, insert the vertical shaft of the pivot knuckle Figure 11 into the lift-arm pivot hub (Figure...
Operation Training Period Before operating the verticutter reels, evaluate the performance of the reel at the desired setting. Operate them in a clear, unused area to determine if they will achieve the desired results. Adjust them as desired. Operating Tips •...
Maintenance Adjusting the Reel Bearings To ensure long life of the reel bearings, periodically check for Lubricating the Verticutter any reel end play. Check and adjust the bearings as follows: 1. Hold on to the reel shaft and try to move the reel Each cutting unit has 7 grease fittings that you must lubricate assembly side to side (Figure...
Replacing the Blades 5. Continue to install spacers and blades in this manner until the full complement of blades have been installed. Removing the Blades from the Shaft Note: When properly assembled, the blades are staggered in such a manner as to appear like a helix. 1.
Page 14
The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
Page 15
The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
Page 16
Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.