LG LRN8240D Series Owner's Manual page 55

numeric digit and symbols up to 21 characters. The number of
maximum characters is depends on the language.
• Audio: Select the input audio channel. You can hear from the
selected input audio channel. If you set to ON for the IP channel,
you can hear the input audio of the IP camera.
• IP Enable :
On : Uses the camera as a IP camera.
Off : Uses the camera as a Analog camera.
NOTE
• If the [IP Enable] is set to [ON], you cannot set the [Device-
PTZ], [Record-Normal], [Record-Sensor], [Record-Motion],
[Record-Text], [Record-Instant/Panic] and [Event-Motion]
options because they are deactivated.
• This option is not supported for model LRN8240D.
IP Camera
• Channel: Selects the desired channel to set the connected IP
camera.
• Vendor: Selects the IP camera vendor from the drop-down list.
• Model Name: Enter the model name of the IP camera.
• Stream : Select the camera stream you want to display using the
Stream drop-down box.
• Host Name: Enter the IP address of the IP camera.
• User Name: Enter the user ID.
• Password: Enter the user password.
• RTSP/HTTP Port: Enter the RTSP/HTTP port number.
• RTP Mode: Selects the RTP mode from the drop-down list.
ATM/POS Setting
• Interface Device: Select the interface device from the drop-
down list.
• Camera: Select the camera number for mapping with ATM/POS
device.
• Baud Rate: Select the desired parameter to set the
communication speed between DVR and ATM/POS device.
• Data Bits: Select the number of the data bits for RS-485
communication.
• Stop Bits: Select the desired parameter. The stop bit is added to
the last of data, in asynchronous communication.
• Parity: Select the desired parameter. The parity bit is added to
the data, to perform parity check.
NOTE
This option is not supported for model LRN8240D.
Storage
• Overwrite:
- On : Overwrite recording is possible when the partition of
HDD have fully recorded.
- Off: Do not use overwriting.
• Full Warning: When the HDD has overflowed a warning message
is displayed.
• Auto Delete: Set the auto delete date. If you set the auto delete
date, the recorded data will be deleted except the data within
the selected date period of time. The Auto Delete function is
activated every 35 minutes.
• Storage Saving : Saves the storage space by reducing the quality
of the recorded data.
Display settings
• Channel: Selects the desired channel to adjust.
Channel Composition
• Name: Selects the desired channel.
NOTE
This option is not supported for model LRN8240D.
PTZ
Settings for the PTZ cameras connected via the data port of the
RS-485 terminal.
• Port: Selects the connected data port of the RS-485 terminal
on the rear panel. The DATA 2 port is used to control the PTZ
camera connected to DVR or to control by using the LKD1000
controller. If you want to use the PTZ camera via DATA 2 port,
you should set the [Remote Controller ID] to [NONE]. If you use
the LKD1000 controller to control the DVR via DATA 2 port, you
should set the [Remote Controller ID] number between 1 and
16.
• Control ID: Selects the PTZ camera ID. Make the same settings
as the PTZ camera.
• Protocol: Selects the protocol supported by PTZ camera.
• Baud Rate: Selects the communication speed.
NOTE
This option is not supported for model LRN8240D.
Video Adjustment
Adjust the brightness, contrast and color settings of each camera
channel. You can see the settings screen from the preview windows.
• Brightness: Adjust the brightness value from 0 to 100 for the
selected channel.
• Contrast: Adjust the contrast value from 0 to 100 for the selected
channel.
• Color: Adjust the color value from 0 to 100 for the selected
channel.
NOTE
This option is not supported for model LRN8240D.
LG Network Client Program 55
5