When Check the AC power cord for possible damages. Keep voltage exceeds the specified limits, check each special the part or the lead away from any heat-emitting part. materials. Samsung Electronics...
Page 6
Critical safety parts should be bracketed with ( Use only regular parts for replacements (in particular, flame resistance and dielectric strength specifications). Irregular parts or materials may cause electric shock or fire. Samsung Electronics...
5. Check for insulation between the blade of the AC plug 10. The sharp edges of the metal material may cause and that of any conductive materials (i.e. the metal physical damage, so ensure wearing protective gloves panel, input terminal, earphone jack, etc). during the repair. Samsung Electronics...
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...
5. Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product. Also check the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause fire or electric shock. Samsung Electronics...
4. When replacing the Side AV Ass'y : No adjustments required 5. When replacing the PIP Module : No adjustments required 6. When replacing the Control Ass'y : No adjustments required 7. When replacing the PFC Ass'y : No adjustments required Samsung Electronics...
Bus Stop Off CHECKSUM 0000 G2 Adjust RESET T-RHMNSA-XXXX 20XX/XX/XX 3. Functions of the Keys within Service Mode. MENU Show all menus Move the cursor to select an item. ▲ / ▼ Adjust the selected configuration value ◀ / ▶ Samsung Electronics...
Var. Plug Play Var. StandBy LED Var. 2. Option2 Model Item Var./Fixed CL29M21FQ CL29M16MQ CL29M2MQ CL29T21FQ X-Ray Protect Var. High Deviation Var. V-Guard Var. Var. Var. 4:3 Zoom 4:3 Zoom 4:3 Zoom Var. Hotel Mode Var. Philippines Var. Samsung Electronics...
Page 14
V Shift Var. H EW Var. H Shift Var. V Linearity Fixed V S-Correction Fixed V Slope Fixed V Scroll Fixed V Zoom Fixed H Parabola Fixed Upper Corner Fixed Lower Corner Fixed H Trapezium Fixed Fixed Angle Fixed Samsung Electronics...
Page 16
VM Mode Fixed VM Gain Fixed VM Delay Fixed Blue Stretch Fixed G2 Adjust Bright Fixed Soft Clipping Level Fixed Peak White Limit Fixed Cathode Drive Level Fixed IF Demodulator Fixed Fast Filter IF PLL Fixed FOAB Fixed Samsung Electronics...
Page 17
IF Preset Value 2 Fixed IF PLL Osc Preset Value Fixed Preset Gain R Fixed Preset Gain G Fixed Preset Gain B Fixed Turbo Center Frequency Fixed DCXO Caps/NICAM Center Fixed DCXO Scaning Control Gain Fixed Component H-Shift Offset Fixed Samsung Electronics...
Page 18
Fixed Chroma Trap Mode Fixed Black Current Measure Line Fixed EHT Tracking Mode Fixed 10. YC Delay Model Item Var./Fixed CL29M21FQ CL29M16MQ CL29M2MQ CL29T21FQ PAL Delay Fixed NTSC Delay Fixed PAL AV Delay Fixed NTSC AV Delay Fixed Samsung Electronics...
Page 19
12. Bus Stop : Off 13. Checksum : 0000 14. G2 Adjust : Screen Adjust OK/NG/Obove 15. Reset Item DATA MICOM(UOC3) T-RHMNSA-**** T-RHMNSA-**** T-RHMNSA-**** Version NO. 2005/**/** 2005/**/** 2005/**/** White Balance 275/275/40ft 275/275/40ft 275/275/40ft (NTSC/PAL N-M) 265/265/2.0ft 265/265/2.0ft 265/265/2.0ft Samsung Electronics...
2. Press "Power Off → Mute → 1 → 8 → 2 → Power On" using the remote control and enter Factory Mode. 3. Enter Deflection Mode. 4. Adjust the V-AMP, V-SHIFT, H-AMP and H-SHIFT items so that the width becomes 5 and the height becomes 4. 3-10 Samsung Electronics...
Page 21
7. When the adjustments are complete, display the Lion pattern and check that the picture size has not been changed. If there is no change, finish the adjustments. Samsung Electronics 3-11...
1. To enter Service Mode, press the keys on the remote control according to the following sequence. (in Stand-by status) Mute → 1 → 8 → 2 → Power On 2. When entering Service mode, the software information is displayed at the top of the service mode menu OSD. ex) T-RHMNSA-1000 20XX/XX/XX 3-12 Samsung Electronics...
Page 23
- Check the "Flash selection" item is appoint "Manual" - You can adjust program delay time for program speed but we use the normal "5[ms]" - Check the green lamp if this is sometime red lamp you can not programming Samsung Electronics 3-13...
Page 24
- Click the “Erase Flash” button for before program erase - You can select flash selection item but we use normal “All” mode - Change the “Select flash ROM to erase. When ready press Send.” - Click the “Send” button 3-14 Samsung Electronics...
Page 25
- Click the “Browse” button and find the new program folder in your computer - Click the “Send” button 6. Verify new program - Click the “Verify Flash” button - Change the “Select flash to verify correct programming. When ready press Send.” - Click the “Send” button Samsung Electronics 3-15...
4. Slowly turn the Static Focus VR counter clockwise so that the center vertical line is the most clearly displayed. [adjusted point : Center(2/1)] After Adjustment Single 5. Check the entire screen focus and repeat steps 3 to 4, if necessary. Focus VR 3-16 Samsung Electronics...
Page 27
2. Initialize all settings to the values appropriate to the corresponding model. 3. Display the Toshiba pattern. 4. First check IBRM in "G2 Adjust" of Factory and adjust Screen VR until the color of IBRM item turns green. Screen Samsung Electronics 3-17...
Page 28
4. When the adjustment is finished, check the following checklist. - If there is a spot on the screen when turning the TV set off/on, adjust the Screen Voltage again. - If there is a ghost line on the screen, adjust the Screen Voltage again. 3-18 Samsung Electronics...
2) Check that the Master Switch has been pressed. 3) Check that the transmitter is turned on. 4) Check that transmitter device selection is set to TV. 5) Check that the signal cable is properly connected. 6) Check that channel setting has been set. Samsung Electronics...
Page 34
+ D “ ” 1 805A t r a D “ 805A” Q “ ” 1 805A) IC601 IC901 IC201S TU01S Q “ ” 1 IC802 r i a IC803 Q401S IC804 T401S IC801S QE01 IC301S Power cord Samsung Electronics...
You can check the checksum according in the following order. Factory Mode → Checksum → Right Button → Calculate Checksum → Output Checksum (e.g. 3036) ■ Checksum Examples T-TR2PEU-1000 : checksum = 8036 T-TR2PEU-1010 : checksum = B612 Samsung Electronics...
Check the +125V line B+ line “D811”(D811A) open T444 B+ Pin #3 Change IC201 Check IC501 Pin#6 and check Open and check Change the “D811” Check the “Q401” (D811A) Change the “Q401” Change IC501 Compleat repair no picture Samsung Electronics...
7-2-2 Power Block Diagram Switching IC (FREEW6750F) 7 ( . 7 ( . l i f - r e t 7 ( . y a l o i t t u p s t l , V . . l o Samsung Electronics...
Page 43
(TDQ-6F/13F2S) F I - F I - / Y ( ) i 0 KEY1 MATRIX KEY3 MATRIX POWER KEY (CH UP/DOWN, H-DRIVE/S-CASTLE VOL UP/DOWN, MENU) V-DRIVE/V-sync 7-2-4 CRT Drive Block Diagram VIDEO AMP (TDA6108AJF) r e t UOC3 Samsung Electronics...
* K16A is a typical analog CRT TV set adapted to New mutiple-function IC (UOC3). UOC3 = UOC2 + Sound processor. * Only IF block is out of UOC3 IC. (Split type) * K16A have a good picture quality,called DNIe Jr. (Gamma & Dynamic skin tone) Samsung Electronics 13-1...
* Main trans have 2pins for sound B+option. * We use 2types Sound Amp. (TDA7297SA can output over 10W+10W, TDA7266SA can output under 7W+7W) * UOC IC need variety power supply, so we use 3type IC vol.regulator. (78R33,78R05,78R08) 13-2 Samsung Electronics...
Page 47
* PIP, Component(480i) are switched at the PIP module, so it can't display sub-picture at the Component mode. 13-2-4 CRT Block Description VIDEO AMP (TDA6108AJF) r e t UOC3 * R,G,B output from UOC3 IC is small, so we need high-output video amp(TDA6108AJF). Samsung Electronics 13-3...
Schematic Diagram 10. Schematic Diagram 10-1 Power & Deflection Block This Document can not be used without Samsung’s authorization. TP01 Power Signal TP02 TP02 TP03 TP08 TP01 TP03 TP08 Samsung Electronics 10-1...
Schematic Diagram 10-2 IF & UOC(Chroma_Micom) Block This Document can not be used without Samsung’s authorization. TP04 Power Signal TP07 TP05 TP06 TP06 TP07 TP04 TP05 10-2 Samsung Electronics...
Schematic Diagram 10-3 PIP & CRT Block This Document can not be used without Samsung’s authorization. TP09 Power Signal TP10 TP11 Samsung Electronics 10-3...