If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after com- pletion of soldering work. If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer. XE-A21S LEAD-FREE SOLDER...
4) While holding down the FEED key, plugin the AC cord to the wall outlet. Note: In case power failure occurs when the machine has no battery attached to it, the master reset operation is automatically performed after the power has been restored. XE-A21S MASTER RESET and program reset 1 – 1...
LOWER TAX LIMIT 5.0000% TAX3 0.20 ------ TAX4 ("------": INHIBIT) C#01 CLERK.01 Clerk No. /Clerk name C#02 CLERK.02 : VARIOUS PROGRAM C#25 CLERK.25 Refer to the programming section about the data of each JOB. XE-A21S PROGRAM MODE 2 – 1...
“OPEN”, its amount entry type is set as below automatically. Inhibited ★ 1 “INHIBIT” “PRESET” Open “OPEN & PRESET” 1 “OPEN” Preset Open & Preset MRS = 0 MRS = 00010071 (TAXABLE 1, NORMAL, SIGN (+), HALO = 7, OPEN) XE-A21S PROGRAM MODE 2 – 3...
Page 7
C: LIMITATION DIGITS (0=INHIBIT) = 0 to 8 XXXX.XXXX: Rate for CONVERSION (0.0000 to 9999.9999) MRS = 008 The DECIMAL POINT must be entered for setting the decimal digits. MRS = 0.00 (%n) 0.0000 (CONVERSION) XE-A21S PROGRAM MODE 2 – 4...
Page 8
Y: 0 = SUBDEPT, 1 = PLU YYY 3 [00] KEY MRS = 1 (PLU type) YYY: CHARACTER CODE (3 DIGITS) (or [000] KEY ACCORDING TO PGM PRESET) MRS = Refer to the following table XE-A21S PROGRAM MODE 2 – 5...
***RA SHARP ***PO CUSTOMER TRA NS CT THE BEST NET3 (SALES) N E T 3 CASH C A S H CHECK CHECK GROSS CHARGE1 CHARGE REFUND CHARGE1 CHARGE - CONVERSION (PRESET RATE) CONV 1 XE-A21S PROGRAM MODE 2 – 6...
Page 10
(Case of interval between break point is 1 dollar or more and less than MRS = 100.00 (%) 100 dollar, 36 breakpoints is programmed for each table.) * DEPRESSION OF THE [SBTL] KEY AT THE FOLLOWING POINTS MEANS A TAX TABLE DELETE OPERATION. XE-A21S PROGRAM MODE 2 – 7...
★ PRINT [JOB#1] MACHINE No. (6digits) -- XXXXXX -- NOT PRINT MRS = 000000 D: DATE PRINTING (for all receipt) ★ PRINT [JOB#2] CONSECUTIVE No. (4digits) -- XXXX -- NOT PRINT MRS = 0000 XE-A21S PROGRAM MODE 2 – 8...
Page 12
3-LINE HEADER INSTEAD OF GRAPHIC LOGO G: Date format ★ GRAPHIC LOGO ONLY ★ M-D-Y GRAPHIC LOGO AND 3-LINE FOOTER D-M-Y 6-LINE HEADER Y-M-D GRAPHIC LOGO AND 3-LINE HEADER H: TAB 3-LINE HEADER AND 3-LINE FOOTER ★ XE-A21S PROGRAM MODE 2 – 9...
Page 13
MRS = 00000000 Disable A, B, C, D, E, F, G, H: Not used (Fixed at “00000000”) D: Copy Receipt ★ E: Entry that causes the merchandise SUBTOTAL to be smaller than zero. ★ Enable Disable XE-A21S PROGRAM MODE 2 – 10...
Page 14
F: GST EXEMPT on X/Z It is available only at “RECEIPT PRINTER TYPE”. ★ PRINTED NOT PRINTED GH: TAX SYSTEM = 00 to 11 AUTO TAX = 00 CANADA TAX (GST TYPE nn) = 01 to 11 XE-A21S PROGRAM MODE 2 – 11...
Page 15
(In case of “ US$”, the number of character is 3.) Ex) Case of “ US$”: (The currency symbol means “US$”) |AAAADEPARTMENT01 US$10000.00 | HEADER Programmed symbol 05/02/2006 12:34PM DATE/TIME/CLERK NO 123456#1234 BETTY___ MACHINE NO. /CC-NO. /CLERK NAME *PGM* MODE TITLE JOB# XE-A21S PROGRAM MODE 2 – 12...
Page 16
[JOB#140] Format SD CARD This job formats SD card. (It deletes all data on SD card.) After formatting card, the folder \SHARP\ECRXXX01 is made to a root HEADER directory. And then, \ALL, \PROGRAM, \SALES, \EJPRINT, \EJ and \LOGO are...
Page 17
E - S d - P. O F F DISPLAY: ERROR MESSAGE POWER OFF ERROR AT THE DEVICE CONTROL PRINT : MESSAGE of POWER OFF SET DATA&TIME AGAIN (The message is fixed in ROM.) (Issuing Receipt) XE-A21S PROGRAM MODE 2 – 14...
: Text “abcABC”. [NUMBER] 3 [1] [2] [3] 3 [NUMBER] 3 [1] [2] [3] : Text “123” and numeric number 123. [DC] 3 [A] [B] [C] 3 [DC] 3 [A] [B] [C] : Text “ABCABC”. XE-A21S PROGRAM MODE 2 – 15...
Page 19
Ä ñ Ö Ü Š – ç ¿ (DC) Note: The character of this table is for reference. Please see actual display. (DC) : Double Code : ECR Control Character (Not used for text) XE-A21S PROGRAM MODE 2 – 16...
<Help Menu> Print menu [HELP] Date/Time setup Rate of TAX setup Department setup Sales Z report Logo setting Receipt issue What is P in Display What is ERROR 32 SD card command Install PC software XE-A21S PROGRAM MODE 2 – 17...
Page 21
LAYOUT ON KEYBOARD OR L:LINE NUMBER(1-6) NUMERIC KEY ON KEYBOARD. TEXT CAN BE ENTERED BY USING THE CHARACTER LAYOUT ON KEYBOARD OR NUMERIC KEY ON KEYBOARD. 3)GRAPHIC LOGO PLEASE REFER TO CUSTOMER SUPPORT TOOL XE-A21S PROGRAM MODE 2 – 18...
Page 22
MACHINE NO./CC-NO./CLERK NAME 8 WHAT IS ERROR 32 MODE TITLE [ ERROR STATUS ] NO ENTRY OF CLERK CODE [ RESOLUTION ] ENTER A CLERK CODE EX ) ENTRY OF CLERK #1 1- [ CLK# ] XE-A21S PROGRAM MODE 2 – 19...
Page 23
Z1 : Daily Z report X2 : Periodic X report Z2 : Periodic Z report (X report): The corresponding data is held in the ECR. (Z report): The corresponding data is cleared in the ECR. XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE 3 – 1...
Page 24
In that case, the contents of EJ memory is printed just after issued general Z1 report. (Issuing general Z1 report 3 Clear daily DEPT & TRANS memory 3 Issuing EJ memory 3 Clear EJ memory) XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE 3 – 2...
“Customer Support Tool” software on PC. Maximum 400 times data is kept in SD Card when the SD memory is not full. Note: After saving EJ data, ECR is clear the Electronic Journal memory. XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE 3 – 3...
Page 26
S d - A C C E S S . DISPLAY : “ . ” is blinking while executing job. PRINT : (NON) --- Continue to JOB END MESSAGE (NEXT PAGE) XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE 3 – 4...
Page 27
Over limitation of data records (Over max record in sales or EJ data.) <<< Reserved >>> SD CARD ERROR (Anyhow error except above SD ERROR is occurred when ECR accesses SD Card.) XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE 3 – 5...
Page 28
COPYRIGHT 2006 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted. In any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.