Sony hcd-gn1000d Service Manual page 19

QQ
3 7 63 1515 0
Procedure:
1. Press button to turn on the system.
?/1
2. Press [TUNER/BAND] button repeatedly to select the "AM".
3. Press button to turn off the system.
?/1
4. Press [ENTER] button and
system will turn on automatically. The message "AM 9k STEP"
or "AM 10k STEP" appears on the fluorescent indicator tube
and thus the channel step is changed.
[DVD SHIP MODE (WITH MEMORY CLEAR)]
• This mode moves the optical pick-up to the position durable to
vibration and clears all data including preset data stored in the
RAM to initial conditions. Use this mode when returning the
set to the customer after repair.
Procedure:
1. Press button to turn on the system.
?/1
2. Select DVD function.
button, [SOUND FLASH] button and
3. Press
x
simultaneously during "DVD NO DISC" condition. The
system will turn off automatically.
4. After the "STANDBY" blinking display finishes, a message
"MECHA LOCK" appears on the fluorescent indicator tube and
the DVD ship mode is set.
[DVD SHIP MODE (WITHOUT MEMORY CLEAR)]
• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
TE
L 13942296513
Procedure:
1. Press button to turn on the system.
?/1
2. Select DVD function.
3. Press [DVD] button and
"DVD NO DISC" condition. The system will turn off
automatically.
4. After the "STANDBY" blinking display finishes, a message
"MECHA LOCK" appears on the fluorescent indicator tube and
the DVD ship mode is set.
[DVD TRAY LOCK MODE]
• This mode is used to lock the disc tray. When this mode is
activated, the disc tray will not open when [OPEN/CLOSE]
button or [EX-CHANGE/DISC SKIP] button is pressed. The
message "LOCKED" appears on the fluorescent indicator tube.
Procedure:
1. Press button to turn on the system.
?/1
2. Select DVD function.
button and [OPEN/CLOSE] button simultaneously
3. Press x
and hold down until "LOCKED" or "UNLOCKED" appears
on the fluorescent indicator tube (around 5 seconds).
[TV/SAT SWITCHING]
• This mode let you switch from TV to SAT and vice-versa.
Procedure:
www
1. Press button to turn on the system.
?/1
2. Select TV function.
3. Press [TV/SAT] button and
function will change to SAT. Press the same buttons again to
.
change from SAT to TV.
http://www.xiaoyu163.com
button simultaneously. The
?/1
?/1
button simultaneously during
?/1
x ao u163
y
button simultaneously. The
?/1
i
http://www.xiaoyu163.com
2 9
8
[DVD COLOR SYSTEM]
• This mode let you change the color system of the video output
from PAL to NTSC or vice-versa.
Procedure:
1. Press button to turn on the system.
?/1
2. Select DVD function.
3. Press button again to turn off the system.
?/1
4. Press X button and
will turn on automatically.
5. The message "COLOR PAL" or "COLOR NTSC" appears on
the fluorescent indicator tube.
[REMOTE COMMANDER DISABLE MODE]
• This mode let you disable the remote commander reception. When
this mode is activated, the system will not response if the button
on the remote commander is pressed. The message
"RemoteDisable" appears on the fluorescent indicator tube.This
mode is essential for conducting test and repairing when no
interruption from the other remote commander is expected. This
button
mode is cancelled automatically when the AC power supply is
cutoff.
Procedure:
1. Press button to turn on the system.
?/1
2. Press
x
simultaneousl untill"RemoteDisable" or "RemoteEnable"
appears on the fluorescent indicator tube.
Q Q
3 6 7 1 3 1 5
[TCM OFFLINE MODE]
• This mode is used to prevent the system from turning off
automatically when TCM is not connected. Therefore,
measurements can be done even when TCM is not connected
during production.
• Procedure:
1. When the system is turned off, press [EQ BAND] button, [TAPE
A/B] button and
turn on automatically.
2. The message "TCM OFFLINE" will appears on the fluorescent
indicator tube.
• To release from TCM Offline Mode, perform "COLD RESET" or
turn off the power supply.
[MTK FIRMWARE DISPLAY]
• This mode is used to display the MTK firmware version.
• Procedure:
1. Press button to turn on the system.
?/1
2. Press [DVD] button to switch to DVD function.
3. Press button again to turn off the system.
?/1
4. Press x button and
The system turns on automatically.
5. The version of MTK firmware appears on the TV screen.
[MTK OFFLINE]
• This mode is used to enable audio output from the function other
co
than DVD function in order to check the audio output from the
system without connecting MTK.
.
• Procedure:
1. Press button to turn on the system.
?/1
2. Press
x
simultaneously and the message "MTK OFFLINE" appears on
the fluorescent indicator tube.
HCD-GN1000D
9 4 2 8
button simultaneously. The system
?/1
button, [FLANGER] button and [DISC 2] button
0 5 8 2 9 9 4
button simultaneously. The system will
?/1
button.
?/1
m
button, [FLANGER] button and [DISC 1] button
9 9
2 8 9 9
19