LASER SAFETY INFORMATION For U.S.A Class 1 LASER-Product This product is certified to comply with DHHS Rules 21 CFR Subchapter J. This product complies with European Standard EN60825 (or IEC Publication 825) For all areas This equipment is classified as a class 1 level LASER product and there is no hazardous LASER radiation. Caution: (1) Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Page 7
Handling This computer has been designed so as to minimize shock to the LCD and hard disk drive, etc., but no warranty is provided against such trouble. Therefore, as a precision instrument, be extremely careful in the handling. Do not carry the computer while the display is open, or carry it by gripping the display or the cabinet around the display (see figure A).
1 Connection Diagram Connection by Cable Connection Cable DFUP1368YA PSW-DVD-MAIN FPC Direct connection by Connectors LCD Cable DFJS893YA Parts on Bottom Side Speaker Cable L DFJS897ZA Speaker Cable R DFJS898ZA DC-IN Cable DFJS878YB LAN Cable DFJS895ZA Modem Cable DFJS896YA PAD-HDD-MAIN FPC DL3UP1470GBW Antenna Cable L DFJS899ZA...
2 Disassembly & Reassembly Instructions 2.1. Disassembly Flowchart · The chart below shows the various parts which should be removed in order to remove the parts that are to be replaced. · Parts can be replaced efficiently by following the disassembly steps in the chart. Main Unit Main Unit 2.2.1...
Page 10
2.2. Disassembly 2.2.1. Preparations 2. perate the Open Button of the LCD Unit, and open the LCD Block to an angle of 90 degrees or more. · Before disassembly, be sure to perform the following Release the four hooks of the LCD Unit and the two hooks, steps.
Page 11
3. Operate the Open Button of the LCD Unit, and open the 7. Remove the nine Screws (F) of the Top Case Ass’y. LCD Block to an angle of 90 degrees or more. Screw (F): DRQT2+G6FKL 4. Remove the Screws (E) and the six Hooks, and then remove the Side Cover (R).
2.2.4. Removing the LCD Block 2.2.6. Removing the MDC Modem Board · Preparation: Make sure that the steps in sections 2.2.1 · Preparation: Make sure that the steps in sections 2.2.1 to 2.2.3 have been taken first. to 2.2.5 have been taken first. (The entire unit is now standing upright with the LCD 1.
Page 13
2.2.8. Removing the Latch Knob 2.2.9. Removing the DVD-ROM & CD- R/RW Drive and Power SW · Preparation: Make sure that the steps in sections 2.2.1 to 2.2.5 have been taken first. · Preparation: Make sure that the steps in sections 2.2.1 1.
Page 14
2.2.10. Removing the Main Board/Wireless 9. Peel off the tape that secures the Wireless LAN Module. LAN Module FPC (PAD-HDD-MAIN FPC) CN36 Wireless LAN · Preparation: Make sure that the steps in sections 2.2.1 Module to 2.2.4 have been taken first. Top Case 1.
2.2.11. Removing the HDD/Pad FPC 4. Peel off the Pad Sheet, and remove the Touch Pad from the Pad Button. /Touch Pad Preparation: Make sure that the steps in sections 2.2.1 to Touch Pad 2.2.4 and section 2.2.10 have been taken first. 1.
Page 16
2.2.12. Removing the Antenna Board (L), 2.2.14. Removing the LCD Front Ass’y/Hinge (L), (R) · Preparation: Make sure that the steps in sections 2.2.1 · Preparation: Make sure that the steps in sections 2.2.1 to 2.2.4 and section 2.2.10 have been taken first. to 2.2.4 have been taken first.
2.2.15. Removing the LCD Unit/LCD Cable 5. Remove all the hooks (6 at the top, 5 at the bottom and 3 on each side) of the LCD Front Case Ass’y, and remove the · reparation: Make sure that the steps in sections 2.2.1 to LCD Front Case Ass’y.
Page 18
2.3. Reassenbly instructions 2.3.1. Attention when CF-Y4H series is repaired · Execute writing BIOS ID when you exchange the Main Board. · Parts (sheet and rubber) etc. related various the conductive cloth and heat spreader cannot be recycled. Use new parts. 2.3.2.
Page 19
Assenbly of Hinge Hinge insertion details Hinge L Conclusion position Insert in the divergence part of the LCD Cable before installing Hinge (L). LCD Panel Hinge L Hinge R Combination procedure of LCD Case The order of setting hooks: A B C D E Hook position LCD Front Case LCD Rear Case...
Page 20
2.3.3. Line processing of Antenna Cable Hang on the hook, and hold down the part of Pass the outside of this rib. Processing chart seen from core side 2.3.4. Installation of Disk Cover Click Plate Screw Bottom Case Disk Cover Click Plate Draw shaking clockwise when you arrange the Disk Cover Click Plate.
Page 21
2.3.5. Bend of PAD FPC Bend PAD FPC and put into the state in a right picture. (The bend margin of error PAD FFC Dotted line: Valley type bends. Solid line: Mountain type bends. 2.3.6. Static electricity removal of PAD FPC Remove static electricity on the point of contact side of connector (CN900) with the brush when you install PAD FPC in the Board.
Page 22
2.3.7. Installation of touch pad Pad Ring Touch Pad Pad Button Insert FPC The standard of the FPC insertion is FPC reinforcement board and PAD sheet edge side. The Touch Pad back tape affixation specification Installation of Pad Ring and Touch Pad Match the Pad Ring to the convex part (two places).
Page 23
2.3.8. Line processing of Modem Cable and the order of tightening screw of MDC Modem The order of tightening Screw: A B MDC tape putting specification MDC Modem Surface side Screw B MDC Modem Screw A Tag Part Connector Modem Cable insertion MDC Tape MDC Modem back side...
Page 24
2.3.10. Line processing of Speaker Cable Pass the under. Catch for the pin in two places. Catch for the pin CN37 CN27 2.3.11. Attention when Speaker is exchanged Assembly of Speaker R Side + Side - Side Speaker Ring Soldering Long Speaker Cable R Speaker...
Page 25
2.3.12. Line processing of DC-IN Cable 1. Shild film wrapped 2. Wrap the tape on Shild film. around the DC-IN cable. Cover all Shild film with the tape. Shild film Tape DC-IN Cable DC-IN Jack 10 3mm Speaker Cable DC-IN 2.3.13.
Page 26
2.3.14. The order of tightening screws of Drive Unit The order of tightening screws: A Screw C Screw B Screw A Drive Unit Be careful not to pinch when you arrange the drive unit. Bend and stay up. The drive unit must draw in the direction of the arrow and stop the screw.
Page 27
2.3.16. Line processing of LCD Cable Pass the cable under the hinge Take care not to pinch the cables! LCD Cable Align the holes and adhere Inverter Cable Above the hinge: Inverter Cable Below the hinge: LCD Cable 2.3.17. Affixation specification of Disk Protecting (B) Disk side Put between K/B Disk Angle...
Page 28
2.3.18. Assembly of keyboard unit 1. When making repairs, be absolutely sure to re-apply the heatreleasing grease (1) < G-751 > on part A (using an amount equivalent to the size of a pea), and insert according to the ditch of a top case. 2.
Page 29
2.3.19. The order of tightening screw of Each Unit After servicing, tighten the screwsin the following sequence. 1. Tightening the screws of the LCD Unit. 1-1.Tighten DXYN3+J5FNL(J). No.1, No.2 1-2.Tighten XTB26+10GFN(H). No.3, No.4 Screw (H) Screw (J) Screw (H) Screw (J) 2.
Page 30
2.3.20. Assembly of DIMM Cover Unit DIMM Cover heat spreader sheet DIMM Cover Be careful not to get on the edge of the DIMM cover. Please put the DIMM Cover heat spreader sheet according to right Cover Corner of the DIMM Cover Unit. 2.3.21.
Replacement Parts List Note: Important Safety Notice Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer's specified parts. CF-Y4HWPZZBM REF.NO. and AREA PART NO. DESCRIPTION Q'TY Main Block Unit CR2032/S5Y LITHIUM BATTERY DFJS878YB DC-IN CABLE...
Page 35
DFGX0403ZB-1 HINGE COVER L DFGX0404ZB-1 HINGE COVER R DFGX0406ZA-0 RJ DUST COVER DFGX0419ZA-0 DIMM COVER DFHE0463ZA EMI SHEET 3 DFHE0472ZA INSULATION SHEET DFHE0555ZA HINGE GASKET DFHE0793ZB GASKET HINGE DFHE0843ZA LCD MAGNET DFHE0844ZA GASKET PAD DFHE0845ZA GASKET COMBO DFHE0852ZA GASKET USB DFHE0854ZA GASKET HDD DFHE0856ZA...
Page 36
DFKM8168ZB-1 LCD FRONT ASSY K72-1 DFGX0397ZA-0 LCD BATT RUBBER K72-2 DFHG1718ZA-0 LCD RUBBER CUSHION DFMC0613ZA EMI TAPE A DFMC0703ZA SHIELD SHEET DFMD1171ZA JACK HDD ANGLE DFMD1178ZA DISK ANGLE LIGHT DFMD2162ZA LCD PROTECT PLATE DFMD7925YA DISK LOCK ANGLE DFMD7986ZA LCD HOOK DFMD7997ZA KB PLATE DFMX1120ZA...
Page 37
Replacement Parts List Note: Important Safety Notice Components identified by mark have special characteristics important for safety. When replacing any of these components use only manufacturer's specified parts. CF-Y4HWPZZBM REF. NO and AREA PART NO. DESCRIPTION Q'TY MAIN PCB F1J0J106A013 CAPACITOR, 6.3V, 10µF C 11 C 12...
Page 38
C 81 C 89 C 90 C 100 C 102 C 103 C 106 C 107 C 111 C 169 C 174 C 180 C 181 C 184 C 297 C 298 C 347 C 348 C 352 C 354 C 355 C 356 C 363...
Page 39
C 101 C 113 C 115 C 116 C 119 C 120 C 121 C 122 C 125 C 126 C 127 C 128 C 131 C 132 C 134 C 135 C 138 C 139 C 142 C 144 C 152 C 153 C 154...
Page 40
C 222 C 223 C 228 C 229 C 230 C 231 C 232 C 233 C 234 C 235 C 236 C 237 C 239 C 241 C 242 C 246 C 247 C 249 C 250 C 253 C 257 C 258 C 270...
Page 41
C 337 C 340 C 344 C 345 C 349 C 357 C 360 C 364 C 367 C 368 C 391 C 392 C 394 C 399 C 401 C 402 C 403 C 408 C 409 C 413 C 417 C 423 C 429...
Page 42
C 201 C 219 C 238 C 262 C 264 C 266 C 305 C 341 C 343 C 369 C 376 C 378 C 385 C 415 C 416 C 447 C 466 C 601 C 626 C 678 C 729 C 730 C 55...
Page 43
C 366 C 387 C 389 C 390 C 395 C 396 C 397 C 412 C 414 C 418 C 419 C 420 C 421 C 422 C 441 C 616 C 621 C 632 C 633 C 659 C 667 C 679 C 690...
Page 44
C 212 C 218 C 114 DCUM1A1051BD CAPACITOR, 10V, 1µF C 117 C 118 C 123 C 124 C 129 C 130 C 133 C 136 C 137 C 156 C 157 C 158 C 159 C 192 C 198 C 199 C 248 C 292...
Page 45
C 683 C 725 C 190 F1G1H7R0A452 CAPACITOR, 50V, 7pF C 320 C 193 F1G1H6R0A452 CAPACITOR, 50V, 6pF C 322 C 424 C 425 C 251 EEFUD0J151ER CAPACITOR, 6.3V, 150µF C 358 C 410 C 271 F1G1H330A451 CAPACITOR, 50V, 33pF C 272 C 273 C 274...
Page 46
C 362 C 398 C 462 C 384 F1G1A683A014 CAPACITOR, 10V, 0.068µF C 386 C 436 F1J0J475A009 CAPACITOR, 6.3V, 4.7µF C 620 C 642 C 663 C 685 C 463 EEFCD0J470ER CAPACITOR, 6.3V, 47µF C 600 F1H1H104A783 CAPACITOR, 50V, 0.1µF C 602 C 615 C 617...
Page 47
C 668 C 674 F1H1H472A748 CAPACITOR, 50V, 4700pF C 704 F1G1H152A450 CAPACITOR, 50V, 1500pF C 716 F1K1E1060001 CAPACITOR, 25V, 10µF C 717 CF 1 D4CC1103A038 THERMISTOR CN 1 K1MMH2B00003 CONNECTOR CN 2 K1KA02BA0014 CONNECTOR CN 27 CN 31 CN 4 K1MN50B00043 CONNECTOR CN 6...
Page 48
D 622 D 609 B0JCQD000001 DIODE D 611 B0JDAE000004 DIODE D 627 D 630 D 613 MAZ80510ML DIODE D 614 D 615 D 617 D 618 D 640 D 616 MAZ80620ML DIODE D 619 MA2S111-TX DIODE D 621 D 624 B0JCCE000008 DIODE D 625...
Page 49
IC 614 IC 41 C0JBAE000302 IC, LOGIC IC 46 IC 49 IC 42 C0JBAA000346 IC, LOGIC IC 43 IC 44 C1DB00001179 IC, LSI IC 59 C0DBZHG00043 IC, USB POWER CONTROL IC 60 C1DB00001221 IC, USB-ATAPI LSI IC 62 C0ABBA000093 IC, OP AMP IC 601 IC 64 C0CBCBC00181...
Page 50
L 23 EXC28CE201U INDUCTOR L 24 L 26 DDB5Z024E-L INDUCTOR L 54 L 27 J0JCC0000186 INDUCTOR L 28 L 29 L 30 L 31 L 32 L 33 L 34 DDB5Z024C-L INDUCTOR L 35 L 36 L 37 L 56 ERJ6GEY0R00V INDUCTOR L 600...
Page 53
R 33 ERJ2RKF2210X RESISTOR, 1/16W, 221Ω R 39 R 34 ERJ2RKF1000X RESISTOR, 1/16W, 100Ω R 40 R 42 R 37 ERJ2RKF24R9X RESISTOR, 1/16W, 24.9Ω R 38 R 66 R 232 R 41 ERJ2GE0R00X RESISTOR, 1/16W, 0Ω R 114 R 115 R 116 R 117 R 118...
Page 54
R 383 R 384 R 394 R 426 R 428 R 430 R 439 R 442 R 443 R 449 R 604 R 689 R 693 R 784 R 786 R 47 ERJ2RKF80R6X RESISTOR, 1/16W, 80.6Ω R 48 R 49 ERJ2GEJ103X RESISTOR, 1/16W, 10KΩ...
Page 55
R 400 R 402 R 411 R 412 R 419 R 421 R 422 R 425 R 432 R 445 R 446 R 454 R 457 R 459 R 460 R 463 R 616 R 684 R 697 R 698 R 705 R 710 R 711...
Page 56
R 365 R 390 R 391 R 392 R 393 R 401 R 617 R 618 R 651 R 652 R 653 R 654 R 655 R 656 R 788 R 53 ERJ2RKF1002X RESISTOR, 1/16W, 10KΩ R 54 ERJ2RKF1500X RESISTOR, 1/16W, 150Ω R 55 R 56 R 282...
Page 57
R 93 R 94 R 95 R 96 R 97 R 98 R 99 R 100 R 101 R 102 R 103 R 104 R 105 R 106 R 107 R 444 R 112 D1HA56080001 RESISTOR ARRAY R 113 R 140 R 141 R 142 R 143...
Page 58
R 363 R 369 R 371 R 375 R 388 R 395 R 396 R 413 R 418 R 434 R 435 R 436 R 450 R 612 R 621 R 622 R 628 R 629 R 645 R 646 R 649 R 650 R 690...
Page 59
R 179 R 180 R 181 R 182 R 183 R 185 R 186 R 187 R 188 R 189 R 219 R 234 R 265 R 266 R 268 R 269 R 270 R 271 R 170 D1H83304A024 RESISTOR ARRAY R 175 ERJ2RKF4750X RESISTOR, 1/16W, 475Ω...
Page 60
R 389 R 458 R 258 ERJ2GEJ473X RESISTOR, 1/16W, 47KΩ R 261 R 263 R 264 R 299 R 303 R 348 R 368 R 407 R 408 R 455 R 623 R 661 R 687 R 773 R 272 ERJ2GEJ472X RESISTOR, 1/16W, 4.7KΩ...
Page 61
R 350 ERJ2GEJ221X RESISTOR, 1/16W, 220Ω R 794 R 380 ERJ2RKF3901X RESISTOR, 1/16W, 3.9KΩ R 385 ERJ2RHD103X RESISTOR, 1/16W, 10KΩ R 608 R 611 R 403 ERJ6GEYJ221V RESISTOR, 1/10W,220 Ω R 415 ERJ2RHD132X RESISTOR, 1/16W, 1.3KΩ R 768 R 423 R 424 R 452 ERJ2GEJ470X...
Page 62
R 640 ERA3YEB303V RESISTOR, 1/16W, 30KΩ R 644 ERJ2GEJ684X RESISTOR, 1/16W, 680KΩ R 748 ERJ2RKD114X RESISTOR, 1/16W, 110KΩ R 648 ERJ2GEJ225X RESISTOR, 1/16W, 2.2MΩ R 658 ERJ6GEYJ561V RESISTOR, 1/10W, 560Ω R 759 D1BDR0680001 RESISTOR, 1/8W, 0.068Ω R 760 R 659 ERJ6GEYJ222V RESISTOR, 1/10W, 2.2KΩ...
Page 63
G5BYC0000010 TRANCE H0J143500058 OSCILLATOR, 14.318MHz H0J327200115 OSCILLATOR, 32.768KHz H0J250500025 OSCILLATOR, 25MHz H2D800400015 OSCILLATOR, 8MHz H0J300500011 OSCILLATOR, 30MHz ZA 1 DRHM0099ZA SPACER ZA 2 ZA 3 LED/POWER PCB C 910 F1H1H104A783 CAPACITOR, 50V, 0.1µF C 913 F1H1H101A737 CAPACITOR, 50V, 100pF C 914 CN 910 K1MN30B00137 CONNECTOR...