SPECIFICATIONS Camera Power consumption (during shooting with the LCD screen on) [System] 0.95 W Image device 9.10 mm (1/1.8 type) color Operating temperature CCD, Primary color filter 0 to 40°C (32 to 104°F) Total pixel number of camera Storage temperature Approx.
Page 3
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
TABLE OF CONTENTS Section Title Page SERVICE NOTE 1-1. Description on Self-diagnosis Display ···························· 1-1 1-2. Process After Fixing Flash Error ····································· 1-1 1-3. Method for Copying or Erasing the Data in Internal Memory ··········································································· 1-2 1-4. Precaution on Replacing the SY-154 Board ···················· 1-3 DISASSEMBLY 2-1.
1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY Self-diagnosis display • C: ss: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss: ss Contact your Sony dealer or local authorized Sony service facility.
Page 6
1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note 1: When replacing the SY-154 board, erase the data in internal memory of the board before replacement. Note 2: When replacing the SY-154 board or the IC202 on the SY-154 board, execute formatting and initialize the internal memory after replacement.
1-4. PRECAUTION ON REPLACING THE SY-154 BOARD VIDEO OUT Default Data Check When you replace to the repairing board, the written data of repairing board also might be changed to original setting because of broadcast system (NTSC/PAL). When the data has changed because of board replacing etc., check the default data of VIDEO OUT if destination code is right. If not, rewrite to the right value.
2. DISASSEMBLY NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt Do not insert the cable insufficiently nor crookedly. which comes off at the point. (Be careful or some •...
2-1-2. LCD PANEL SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Control Switch Block (1-1 to 1-2) 2 LCD Block (2-1 to 2-8) 2-2 (#3) 1 Control Switch Block 1-1 (#3) 2-3 (Claw) 2-4 (Claw) 2 LCD Block DSC-W100_L2...
2-1-3. CABINET (TOP) SECTION EXPLODED VIEW Follow the disassembly in the numerical order given. 1 Cabinet (Top) Block (1-1 to 1-8) 2 Capacitor Holder Block (2-1 to 2-4) 3 Lens Block (3-1 to 3-4) 1 Cabinet (Top) Block 1-7 (Open) 1-1 (Boss) 1-4 (Claw) 1-3 (Adhesive sheet)
Page 12
2-1-4. BT HOLDER SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 SY-154 Board (1-1 to 1-4) 2 DC-105 Flexible Board (2-1 to 2-13) (Slide in the direction of arrow) 2 DC-105 Flexible Board 2-5 (Boss) 2-1 (Boss) 2-3 (Claw) 2-7 (Claw)
2-2. EXCHANGE METHOD OF BARRIER ASSY Service parts Part Number Part Name Quantity 3-091-427-01 Ring (A), Ornamental X-3954-476-1 Barrier Assy 3-086-156-31 Tapping screw (P2) Tools used Torque driver Soldering iron Weight about 60g Adhesive (Super X) (Note) Note: Use adhesive (Super X) or an equivalent article. Don’t use what becomes white after drying like a quick-drying glue.
Page 14
2-2-2. REMOVE OLD BARRIER ASSY 1 Remove two screws. * Discard the removed screws. 2 Remove the Barrier Assy. * Discard the removed Barrier Assy. * After removing the Barrier Assy, if the “G1 Dust-Proof Ring” was removed, it must be returned to the home position. In returning the ring, adjust the location of a projection to the lens direction.
Page 15
2-2-4. ADHERE THE ORNAMENTAL RING A Apply an adhesive to four recesses on the top surface of the Barrier Assy. * Do not apply too much adhesive. (Make quantity of adhesives into the quantity in which a groove hides.) Meeting a “notch” of the Ornamental Ring A with a “projection” of the group-1 frame, push the Ornamental Ring A into the group-1 frame. * The projection of the spring for preventing static electricity must be tilted.
Page 16
HELP Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. Boss of DC flexible support Claw of main frame DC-105 flexible board DSC-W100_L2 HELP...
3-3. POWER BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. DC-105 FLEXIBLE SY-154 BOARD ST-146 FLEXIBLE BOARD J001 BOARD T002 CN701 CN704 DC IN FB003 D002 F001 L001 ACV_UNREG...
4-2. SCHEMATIC DIAGRAMS Link Link ST-146 FLEXIBLE BOARD (FLASH DRIVE) CD-628 FLEXIBLE BOARD (CCD IMAGER) MC-162 FLEXIBLE BOARD SW-479 BOARD (LCD, CONTROL SWITCH) (MULTI CONNECTOR) RL-064 FLEXIBLE BOARD FP-427 FLEXIBLE BOARD (CONTROL SWITCH) DC-105 FLEXIBLE BOARD CONTROL SWITCH BLOCK (SW60610) (BATTERY IN, DC IN) COMMON NOTE FOR SCHEMATIC DIAGRAMS DSC-W100_L2...
Page 23
4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection • All capacitors are in µF unless otherwise noted. pF : µ Pattern box µF.
Page 24
CD-628 FLEXIBLE BOARD Note: CD-628 flexible complete board and IC001 are not supplied, but they are included in CCD IMAGER CCD block assy. Note: Voltage of IC001, IC002 and Q002 can not be measured, because they are mounted by the side of lens. XX MARK:NO MOUNT CL001 LND045...
Page 25
Schematic diagrams of the SY-154 board are not shown. Pages from 4-6 to 4-12 are not shown. DSC-W100_L2...
Page 27
• Refer to page 4-3 for mark 0. ST-146 FLEXIBLE BOARD FLASH DRIVE T002 D002 L001 FT02P80TP 2.2uH XX MARK:NO MOUNT NO MARK:REC/PB MODE LND019 XE_H C007 145uF 330V R001 CHARGING LND017 CAPACITOR TRIGGER D004 LND018 DOR5352 FLASH C002 SELF-TIMER/ TRIGGER_GND UNIT AF ILLUMINATOR...
Page 28
• Refer to page 4-3 for mark 0. MC-162 FLEXIBLE BOARD DC-105 FLEXIBLE BOARD Note: CN-001(multi connector) is not supplied, but this is included in MC-162 flexible complete board. MULTI CONNECTOR BATTERY IN, DC IN CN001 28P XX MARK:NO MOUNT XX MARK:NO MOUNT (MULTI CONNECTOR) To AV/USB Multi Cable...
4-3. PRINTED WIRING BOARDS Link Link CD-628 FLEXIBLE BOARD MC-162 FLEXIBLE BOARD SW-479 BOARD RL-064 FLEXIBLE BOARD ST-146 FLEXIBLE BOARD DC-105 FLEXIBLE BOARD COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION DSC-W100_L2...
Page 30
4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers’...
Page 31
CD-628 (2 layers) : Uses unleaded solder. Note: CD-628 flexible complete board and IC001 are not supplied, CD-628 FLEXIBLE BOARD but they are included in CCD block assy. LND045 LND044 LND043 LND042 LND041 LND040 LND039 LND038 C007 LND037 LND036 LND035 LND034 LND033 LND032...
Page 32
Printed wiring boards of the SY-154 board are not shown. Page 4-20 is not shown. DSC-W100_L2...
NOTE NOTE 5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown. EXPLODED VIEWS EXPLODED VIEWS Link Link CABINET SECTION LCD PANEL SECTION CABINET (TOP) SECTION BT HOLDER SECTION LENS BLOCK SECTION ELECTRICAL PARTS LIST...
Page 39
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST NOTE: • -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number, the original one. please include the board name. •...
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1. EXPLODED VIEWS 5-1-1. CABINET SECTION ns: not supplied LCD Panel Section (See page 5-3) #26 (SILVER) #27 (BLACK) #20 (SILVER) #21 (BLACK) #20 (SILVER) #20 (SILVER) #21 (BLACK) #21 (BLACK) #20 (SILVER) #21 (BLACK)
Page 41
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-2. LCD PANEL SECTION LCD901 D901 Cabinet (Top) Section (See page 5-4) Ref. No. Part No. Description Ref. No. Part No. Description 1-479-668-11 CONTROL SW BLOCK (SW60610) (SILVER) D901 1-479-623-11 BLOCK, LIGHT GUIDE PLATE (2.5) 1-479-668-21 CONTROL SW BLOCK (SW60610) (BLACK) * 52...
Page 42
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY 5-1-3. CABINET (TOP) SECTION ns: not supplied (including RL-064 flexible board) BT001 SP901 (Size: 5mm x 5mm) BT Holder Section (See page 5-5) : BT001 (BATTERY, LITHIUM SECONDARY) Board on the mount position. (See page 4-23.) Lens Block Section (See page 5-6)
Page 43
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-4. BT HOLDER SECTION ns: not supplied BT901 E (Middle east, Gulf) - 1 5 MIC901 * Refer to the table of page 5-1 about language of SY-154 board. •...
Page 44
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST HARDWARE LIST 5-1-5. LENS BLOCK SECTION ns: not supplied - 1 4 (including IC001 (CCD imager) and CD-628 flexible complete board) (Note 1, 2) (Note 3) (Note 3) (Note 3) Note 1: CCD block assembly is including CD-628 flexible complete board.
CD-628 DC-105 MC-162 RL-064 ST-146 5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description A-1178-700-A CCD BLOCK ASSY (Note 1) < LINE FILTER > (Not supplied) CD-628 FLEXIBLE BOARD, COMPLETE LF001 1-456-583-21 COMMON MODE CHOKE COIL ******************************* (CD-628 flexible complete board and IC001 are not supplied, but they are included in CCD block assy.)
Checking supplied accessories. Other accessories 2-674-774-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (AEP, UK, E, HK, AUS, JE) 2-674-774-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (AEP) Battery Charger Battery Charger 2-674-774-31 INSTRUCTION (READ THIS FIRST) BC-CSG BC-CSG (SPANISH, PORTUGUESE) (AEP, E, JE) 0 1-479-583-21 0 1-479-583-31 2-674-774-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH)
Page 48
HARDWARE LIST (1/2) #1: M1.7 X 2.5 #2: M1.7 X 4.0 #3: M1.7 X 2.5 #4: M1.4 X 2.5 (Tapping) (Black) (Black) (Red) (Dark Silver) 2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81 #5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping) (Black) (Silver)
Page 49
HARDWARE LIST (2/2) #21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping) (Black) (Silver) (Black) (Black) 2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11 #25: M1.7 X 3.0 #26: M1.4 X 2.0 #27: M1.4 X 2.0 #28: M1.4 X 4.0 (Tapping) (Black) (Silver)
Page 50
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)] Toolbar Printing a text Reversing the screens displayed once • To reverse the previous screens (operation) one by one, click 1. Click the Print button 2.