Sony CDX-GT10M Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Car Receiver
  5. CDX-GT10M - Car Audio
  6. Service manual
Sony CDX-GT10M Service Manual

Sony CDX-GT10M Service Manual

Fm/am compact disc players
Hide thumbs Also See for CDX-GT10M:
Table of Contents

Advertisement

Quick Links

QQ
3 7 63 1515 0
SERVICE MANUAL
Ver. 1.2 2006. 09
• The tuner and CD sections have no adjustments.
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
TE
L 13942296513
CD Player section
Signal-to-noise ratio:
120 dB
Frequency response:
10 – 20,000 Hz
Wow and flutter:
Below measurable limit
Tuner section
FM
Tuning range:
87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)
FM tuning interval:
50 kHz/200 kHz switchable
Antenna terminal:
External antenna connector
Intermediate frequency: 10.7 MHz/450 kHz
Usable sensitivity:
9 dBf
Selectivity:
75 dB at 400 kHz
Signal-to-noise ratio:
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz:
0.5 % (stereo), 0.3 % (mono)
Separation:
35 dB at 1 kHz
Frequency response:
30 – 15,000 Hz
AM
Tuning range:
531 – 1,602 kHz (at 9 kHz step)
530 – 1,710 kHz (at 10 kHz step)
AM tuning interval:
9 kHz/10 kHz switchable
Antenna terminal:
External antenna connector
Intermediate frequency: 10.7 MHz/450 kHz
Sensitivity:
30 µV
www
.
Sony Corporation
9-887-163-03
2006I04-1
eVehicle Division
© 2006. 09
Published by Sony Techno Create Corporation
http://www.xiaoyu163.com
x
ao
u163
y
i
http://www.xiaoyu163.com
CDX-GT10M
2 9
8
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
Q Q
3
6 7
1 3
1 5
Power amplifier section
Outputs:
Speaker impedance:
Maximum power output: 52 W × 4 (at 4 ohms)
General
Outputs:
Inputs:
Tone controls:
Power requirements:
Dimensions:
Mounting dimensions:
Mass:
Supplied accessories:
Design and specifications are subject to change
without notice.
FM/AM COMPACT DISC PLAYER
co
.
9 4
2 8
US Model
Canadian Model
CDX-GT10W/GT100/
GT150/GT150S
MG-611XE-186//Q
KSS1000E
0 5
8
2 9
9 4
2 8
Speaker outputs (sure seal connectors)
4 – 8 ohms
Audio outputs terminal (sub/rear switchable)
Power antenna relay control terminal
Power amplifier control terminal
Antenna input terminal
AUX input jack (stereo mini jack)
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
12 V DC car battery (negative ground)
Approx. 178 × 50 × 179 mm
× 2 × 7
(7
in) (w/h/d)
1/8
1/8
Approx. 182 × 53 × 161 mm
× 2
× 6
(7
in) (w/h/d)
1/4
1/8
3/8
Approx. 1.2 kg (2 lb 11 oz)
Parts for installation and connections (1 set)
m
9 9
9 9
1

Advertisement

Table of Contents
loading

Related Manuals for Sony CDX-GT10M

Summary of Contents for Sony CDX-GT10M

  • Page 1 9 kHz/10 kHz switchable without notice. Antenna terminal: External antenna connector Intermediate frequency: 10.7 MHz/450 kHz Sensitivity: 30 µV FM/AM COMPACT DISC PLAYER u163 Sony Corporation 9-887-163-03 2006I04-1 eVehicle Division © 2006. 09 Published by Sony Techno Create Corporation http://www.xiaoyu163.com...
  • Page 2 REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL IN SUPPLEMENTS PUBLISHED BY SONY. OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3 CDX-GT10M 3 7 63 1515 0 Notes on CD-DA/CD-R/CD-RW UNLEADED SOLDER • CD playback: Boards requiring use of unleaded solder are printed with the lead You can play CD-DA and CD-R/CD-RW for audio use. free mark (LF) indicating the solder contains no lead.

  • Page 4: Table Of Contents

    CDX-GT10M 3 7 63 1515 0 TABLE OF CONTENTS 1. GENERAL Location of controls and basic operations ....... 5 Connections ................6 2. DISASSEMBLY 2-1. Sub Panel Assy ..............8 2-2. CD Mechanism Block ............8 2-3. Main Board ................. 9 2-4.

  • Page 5: General

    CDX-GT10M SECTION 1 GENERAL 3 7 63 1515 0 This section is extracted from instruction manual. Location of controls and basic operations Main unit CDX-GT10M J SOURCE button Refer to the pages listed for details. To power on; change the source (Radio/CD/ A OFF button AUX).

  • Page 6: Connections

    CDX-GT10M 3 7 63 1515 0 • CONNECTIONS RCA pin cord (not supplied) AUDIO OUT can be switched to SUB or REAR. For details, see the supplied Operating Instructions. Cordon à broche RCA (non fourni) AUDIO OUT peut être commuté sur SUB ou REAR.

  • Page 7: Disassembly

    CDX-GT10M SECTION 2 DISASSEMBLY 3 7 63 1515 0 Note : This set can be disassemble according to the following sequence. 2-1. SUB PANEL ASSY (Page 8) 2-2. CD MECHANISM BLOCK (Page 8) 2-10. SERVO BOARD 2-4. CHASSIS (T) SUB ASSY 2-3.

  • Page 8: Sub Panel Assy

    CDX-GT10M 3 7 63 1515 0 Note : Follow the disassembly procedure in the numerical order given. 2-1. SUB PANEL ASSY 3 two claws 2 two claws 1 two screws (+PTT 2.6 × 6) 4 sub panel assy L 13942296513 2-2.

  • Page 9: Main Board

    CDX-GT10M 3 7 63 1515 0 2-3. MAIN BOARD 1 three screws (+BTT 2.6 × 5) 2 two screws (+PTT 2.6 × 8) 3 MAIN board L 13942296513 2-4. CHASSIS (T) SUB ASSY 4 claw 2 two screws (+P 1.7 × 2.2) 1 two screws (+P 1.7 ×...

  • Page 10: Roller Arm Assy

    CDX-GT10M 3 7 63 1515 0 2-5. ROLLER ARM ASSY 3 washer (1.1-2.5) 5 roller arm assy 4 gear (RA1) 2 spring (RAR) 1 spring (RAL) L 13942296513 2-6. CHASSIS (OP) ASSY qa chassis (OP) assy 0 coil spring (damper)

  • Page 11: Optical Pick-Up

    CDX-GT10M 3 7 63 1515 0 2-7. OPTICAL PICK-UP 2 chucking arm sub assy 5 claw 1 tension coil spring (CHKG) 7 optical pick-up 6 main shaft 4 rack (SL) 3 screw (+B 1.4 × 5) L 13942296513 2-8. SL MOTOR ASSY (M902) 1 screw (+P 1.4 ×...

  • Page 12: Le Motor Assy (M903)

    CDX-GT10M 3 7 63 1515 0 2-9. LE MOTOR ASSY (M903) 8 screw 0 gear (LE) assy (+M 1.7 × 2.5) 9 bearing (LEB-N) 2 washer qa screw (+M 1.7 × 2.5) qf two toothed lock screws 3 gear (LE1) (+M 1.4 )

  • Page 13: Diagrams

    CDX-GT10M SECTION 3 3 7 6 3 1 5 1 5 0 DIAGRAMS 3-1. BLOCK DIAGRAM — CD SECTION — • R-ch is omitted due to same as L-ch. • Siganal Path : CD DETECTOR MAIN 77 AGCI AGCO...

  • Page 14: Block Diagram - Main Section

    CDX-GT10M 3 7 6 3 1 5 1 5 0 3-2. BLOCK DIAGRAM — MAIN SECTION — ELECTRONIC VOLUME IC401 CD-L 9 CD LCH J330 SECTION OUT SUB-L AUDIO OUT R-CH 8 CD RCH (Page 13) OUT SUB-R R-CH...

  • Page 15: Block Diagram - Display Section

    CDX-GT10M 3 7 6 3 1 5 1 5 0 3-3. BLOCK DIAGRAM — DISPLAY SECTION — • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING SYSTEM CONTROL LCD DRIVER IC501 (3/3) IC901 BOARDS AND SCHEMATIC DIAGRAMS.

  • Page 16: Printed Wiring Boards - Cd Mechanism Section

    CDX-GT10M 3 7 6 3 1 5 1 5 0 3-5. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 15 for Circuit Boards Location. : Uses unleaded solder. (Page 18) 1 3 9 4 2 2 9 6 5 1 3...

  • Page 17: Schematic Diagram - Cd Mechanism Section

    CDX-GT10M 3 7 6 3 1 5 1 5 0 • Refer to page 24 for Waveforms. • Refer to page 27 for IC Pin Description. 3-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 24 for IC Block Diagrams.

  • Page 18: Printed Wiring Board - Main Section

    CDX-GT10M 3-7. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 15 for Circuit Boards Location. 3 7 6 3 1 5 1 5 0 : Uses unleaded solder. J330 JC795 CN601 C484 C474 C775 C774 JW144...

  • Page 19: Schematic Diagram - Main Section (1/3)

    CDX-GT10M 3 7 6 3 1 5 1 5 0 3-8. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 25 for IC Block Diagrams. J330 C484 C474 IC B/D IC401 C401 FB411 FB410 C411 C410 C435...

  • Page 20: Schematic Diagram - Main Section (2/3)

    CDX-GT10M 3 7 6 3 1 5 1 5 0 3-9. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 26 for IC Block Diagrams. JC795 C775 C765 C764 C774 IC B/D C751 D751 D752 C750 D753...

  • Page 21: Schematic Diagram - Main Section (3/3)

    CDX-GT10M • Refer to page 29 for IC Pin Description. 3 7 6 3 1 5 1 5 0 3-10. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 24 for Waveforms. (Page 19) (Page 20) (Page 17)

  • Page 22: Printed Wiring Boards - Key Section

    CDX-GT10M 3 7 6 3 1 5 1 5 0 3-11. PRINTED WIRING BOARDS — KEY SECTION — • Refer to page 15 for Circuit Boards Location. : Uses unleaded solder. LSW902 LSW901 LED908 LED943 R963 S908 R962 LCD901...

  • Page 23: Schematic Diagram - Key Section

    CDX-GT10M 3 7 6 3 1 5 1 5 0 3-12. SCHEMATIC DIAGRAM — KEY SECTION — R981 LSW902(2/2) LED919 LED914 LED908 LED941 R996 R982 R931 R995 LED952 LSW909(2/2) LED916 LED943 R932 R941 R933 R942 LED918 LED913 R961 R963...
  • Page 24 CDX-GT10M Ver. 1.1 3 7 6 3 1 5 1 5 0 • WAVEFORMS • IC BLOCK DIAGRAMS — SERVO BOARD — (CD PLAY) — MAIN BOARD — IC2 BA5966FP-FE2 (SERVO Board) IC1 wd (XTAL) IC501 i; (XIN) OPIN4+ LDCTL 0.7 Vp-p...
  • Page 25 CDX-GT10M 3 7 63 1515 0 IC401 BD3806AFS-E2 (MAIN Board (1/3)) FADER FADER FADER FADER (0~-58, (0~-58, (0~-58, (0~-58, C BUS -∞dB) -∞dB) -∞dB) -∞dB) GAIN+ATT LOGIC (+10~-29, -∞dB) 2ND ORDER LPF fc:OFF,80,120,160Hz 2ND ORDER Q: 0.707 BASS fo:60,70,80,100,120,140,160,200Hz...
  • Page 26 CDX-GT10M 3 7 63 1515 0 IC750 TDA8588BJ/N2/R1 (MAIN Board (2/3)) OUT-FL- C BUS OUT-FL+ OUT-RL- PGND3 OUT-RL+ IN-RL IN-FL S-GND PROTECTION/ DIAGNOSTIC IN-FR IN-RR BEEP OUT-RR+ PGND2 OUT-RR- OUT-FR+ STANDBY/ MUTE OUT-FR- CHIP DETECT/ PGND1 DIAGNOSTIC BATTERY TEMPERATURE...
  • Page 27 CDX-GT10M 3 7 63 1515 0 • IC PIN DESCRIPTIONS IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name Pin Description Laser diode ON/OFF control signal output (L: laser OFF, H: laser ON) Dimmer monitor input from optical pick-up laser diode.
  • Page 28 CDX-GT10M 3 7 63 1515 0 Pin No. Pin Name Pin Description LRCK Not used. (Connect to LRCKIN in this set.) DVDD — Power supply pin (+3.3 V) Focus servo drive PWM signal output (+) FD– Focus servo drive PWM signal output (–) Tracking servo drive PWM signal output (+) TD–...
  • Page 29 CDX-GT10M 3 7 63 1515 0 IC501 MB90488BPF-G-186E1 (SYSTEM CONTROL) (MAIN BOARD (3/3)) Pin No. Pin Name Pin Description AREASEL2 Destination setting pin AREASEL1 Destination setting pin AREASEL0 Destination setting pin COL SW Illumination color select signal input BEEP...
  • Page 30 DAVN RDS data block synchronized detect signal input Not used in this set. Not used. (Open) UNISI SONY bus data signal input Not used in this set. UNISO SONY bus data signal output Not used in this set. (Open) UNISCK SONY bus clock signal output Not used in this set.

  • Page 31: Exploded Views

    CDX-GT10M SECTION 4 EXPLODED VIEWS 3 7 63 1515 0 NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied.

  • Page 32: Front Panel Section

    Part No. Description Remark X-2109-441-1 BUTTON ASSY (S) A-1183-175-A PANEL ASSY, FRONT 3-251-320-11 EMBLEM (NO. 2.5), SONY 2-652-792-11 PANEL, FRONT BACK X-2109-232-1 PANEL SUB ASSY, FRONT 3-250-543-71 SCREW (+B P-TITE M2) X-2109-442-1 KNOB (VOL) (SV) ASSY X-2055-358-1 CASE ASSY (for FRONT PANEL)

  • Page 33: Cd Mechanism Section (1) (Mg-611Xe-186//Q)

    CDX-GT10M 3 7 63 1515 0 4-3. CD MECHANISM SECTION (1) (MG-611XE-186//Q) not supplied (SENSOR board) not supplied not supplied not supplied not supplied L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3372-444-C CHASSIS (T) SUB ASSY...

  • Page 34: Cd Mechanism Section (2) (Mg-611Xe-186//Q)

    CDX-GT10M 3 7 63 1515 0 4-4. CD MECHANISM SECTION (2) (MG-611XE-186//Q) (including M901) M902 not supplied not supplied supplied L 13942296513 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1075-644-A CHASSIS (OP) COMPLETE ASSY A-3372-446-A LEVER (SL) SUB ASSY 3-316-938-91 SCREW (B1.4X5), TAPPING...

  • Page 35: Cd Mechanism Section (3) (Mg-611Xe-186//Q)

    CDX-GT10M 3 7 63 1515 0 4-5. CD MECHANISM SECTION (3) (MG-611XE-186//Q) M903 L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-348-993-01 WASHER 2-186-696-02 BRACKET (LEM-N) 2-186-699-01 GEAR (RA1) 3-345-648-91 SCREW (M1.4), TOOTHED LOCK...

  • Page 36: Cd Mechanism Section (4) (Mg-611Xe-186//Q)

    CDX-GT10M 3 7 63 1515 0 4-6. CD MECHANISM SECTION (4) (MG-611XE-186//Q) L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-186-700-01 GEAR (CHK1) 2-630-962-01 WASHER (SLIT) 3-344-223-01 WASHER 2-590-545-31 GEAR (LE2-M) 3-259-470-12 GEAR (LE1)

  • Page 37: Electrical Parts List

    CDX-GT10M SECTION 5 JACK ELECTRICAL PARTS LIST 3 7 63 1515 0 NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
  • Page 38 CDX-GT10M MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R918 1-216-837-11 METAL CHIP 1/10W A-1183-933-A MAIN BOARD, COMPLETE R921 1-216-041-00 RES-CHIP 1/10W ********************* R922 1-216-041-00 RES-CHIP 1/10W R923 1-216-041-00 RES-CHIP 1/10W 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT...
  • Page 39 CDX-GT10M MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C514 1-162-964-11 CERAMIC CHIP 0.001uF D760 6-500-522-01 DIODE 10EDB40-TA1B2 C516 1-216-864-11 SHORT CHIP D761 6-500-522-01 DIODE 10EDB40-TA1B2 C519 1-107-826-11 CERAMIC CHIP 0.1uF...
  • Page 40 CDX-GT10M MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark L501 1-216-295-11 SHORT CHIP R510 1-216-821-11 METAL CHIP 1/10W L601 1-456-617-11 COIL, CHOKE R511 1-216-821-11 METAL CHIP 1/10W R512 1-216-821-11 METAL CHIP 1/10W <...
  • Page 41 CDX-GT10M MAIN SENSOR SERVO 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R632 1-216-841-11 METAL CHIP 1/10W 1-162-970-11 CERAMIC CHIP 0.01uF R633 1-216-841-11 METAL CHIP 1/10W 1-107-826-11 CERAMIC CHIP 0.1uF...
  • Page 42 CDX-GT10M SERVO 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > MISCELLANEOUS *************** 8-729-904-87 TRANSISTOR 2SB1197K-R 1-776-206-21 CORD (WITH CONNECTOR) (POWER) < RESISTOR > 1-780-199-11 CONDUCTIVE BOARD, CONNECTION...
  • Page 43 CDX-GT10M 3 7 63 1515 0 US Model Canadian Model SERVICE MANUAL Ver. 1.2 2006. 09 SUPPLEMENT-1 File this supplement with the service manual. Subject : Change of key board. When performing service and inspection, check the suffix of the part number of the key board.
  • Page 44 CDX-GT10M 3 7 63 1515 0 • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For schematic diagrams.
  • Page 45 CDX-GT10M 3 7 6 3 1 5 1 5 0 • PRINTED WIRING BOARD — KEY SECTION — : Uses unleaded solder. LSW902 LSW901 R942 LED943 LED951 LED908 R963 R962 S908 LCD901 LIQUID CRYSTAL DISPLAY PANEL R961 LSW910 LSW909...
  • Page 46 CDX-GT10M 3 7 6 3 1 5 1 5 0 • SCHEMATIC DIAGRAM — KEY SECTION — R981 LED919 LED914 LED908 LSW902(2/2) LED941 R996 R982 R931 R995 LED952 LSW909(2/2) LED916 LED943 R932 R941 R933 R942 LED918 LED913 R961 R963...
  • Page 47 CDX-GT10M JACK 3 7 63 1515 0 • ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
  • Page 48 CDX-GT10M 3 7 63 1515 0 Ref. No. Part No. Description Remark R923 1-216-041-00 RES-CHIP 1/10W R924 1-216-041-00 RES-CHIP 1/10W R931 1-216-031-00 RES-CHIP 1/10W R932 1-216-031-00 RES-CHIP 1/10W R933 1-216-031-00 RES-CHIP 1/10W R934 1-216-051-00 RES-CHIP 1.2K 1/10W R941 1-216-033-00 RES-CHIP...
  • Page 49 CDX-GT10M 3 7 63 1515 0 MEMO L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 50 CDX-GT10M 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.

This manual is also suitable for:

Cdx-gt10wGt100Gt150sGt150

Table of Contents