Motorola TalkAbout MH230 User Manual

MH230_EN.qxd:T5025_R 3/1/12 4:33 PM Page 1
Body-Worn Operation
To maintain compliances with FCC/Health Canada RF exposure
®
guidelines if you wear a radio on your body when transmitting
always place the radio in a Motorola-supplied or approved clip
holder, holster, case or body harness for this product. Use of non-
Two-Way Radio
Motorola-approved accessories may exceed FCC/Health Canada RF
exposure guidelines.
User's Guide
If you do not use one of the Motorola-supplied or approved body-
worn accessories and are not using the radio held in the normal
use position, ensure the radio and its antenna are at least 1 inch
(2.5 cm) from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or
without an accessory cable, position the radio and its antenna at
least one inch (2.5 cm) from the body.
Approved Accessories
• 53724: Remote Speaker with Push-to-Talk Microphone
• 53725: Headset with Swivel Boom Microphone
• 53727: Earbud with Push-to-Talk Microphone
• 53728: Flexible Ear Receiver
• 56320: Earpiece with Boom Microphone
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to
electromagnetic interference (EMI) if inadequately shielded,
designed or otherwise configured for electromagnetic compatibility.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
KEM-ML36000-13 MH230
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
interference that may cause undesired operation.
For More Information
IC Canada
For further information, you may contact Motorola Solutions, Inc.
The term "IC:" before the equipment certification number only
as follows:
signifies that the Industry Canada technical specifications were met.
USA and Canada: Call 1-800-638-5119, send e-mail to
Facilities
giant@callcenter.com or visit www.motorolasolutions.com/talkabout.
To avoid electromagnetic interference and/or compatibility conflicts,
Uruguay: Call 00-04-01-78-70-11.
turn off your radio in any facility where posted notices instruct you
Panama: Call 507-340-0293.
to do so. Hospitals or health care facilities may be using equipment
that is sensitive to external RF energy.
Aircraft
Safety and General Information
When instructed to do so, turn off your radio when onboard an
Important Information on Safe and Efficient Operation
aircraft. Any use of a radio must be in accordance with applicable
regulations per airline crew instructions.
Read This Information Before Using Your Radio.
Medical Devices – Pacemakers
The information provided in this document supersedes the general
The Advanced Medical Technology Association recommends that
safety information in user guides published prior to December 1, 2002.
a minimum separation of 6 inches (15 cm) be maintained between a
Transmit and Receive Procedure handheld wireless radio and a pacemaker. These recommendations
are consistent with the independent research by and
Your two-way radio contains a transmitter and a receiver. To control
recommendations of the U.S. Food and Drug Administration.
your exposure and ensure compliance with the general population/
uncontrolled environment exposure limits, always adhere to the
People with pacemakers should:
following procedure:
• ALWAYS keep the radio more than 6 inches (15 cm) from their
• Transmit no more than 50% of the time.
pacemaker when the radio is turned ON.
• To receive calls, release the PTT button.
• Not carry the radio in the breast pocket.
• To transmit (talk), press the Push to Talk (PTT) button.
• Use the ear opposite the pacemaker to minimize the potential
Transmitting 50% of the time, or less, is important because the radio for interference.
generates measurable RF energy exposure only when transmitting
• Turn the radio OFF immediately if there is any reason to suspect
(in terms of measuring standards compliance).
that interference is taking place.
Exposure to Radio Frequency Energy
Medical Devices – Hearing Aids
Your Motorola two-way radio complies with the following RF energy
Some digital wireless radios may interfere with some hearing aids.
exposure standards and guidelines:
In the event of such interference, you may want to consult your
hearing aid manufacturer to discuss alternatives.
• United States Federal Communications Commission, Code of
Federal Regulations; 47CFR part 2 sub-part J.
Medical Devices – Other
• American National Standards Institute (ANSI)/Institute of
If you use any other personal medical device, consult the
Electrical and Electronic Engineers (IEEE) C95. 1-1992. manufacturer of your device to determine if it is adequately
shielded from RF energy. Your physician may be able to assist you
• Institute of Electrical and Electronics Engineers (IEEE) C95.
in obtaining this information.
1-1999 Edition.
• International Commission on Non-Ionizing Radiation Protection
Safety and General Use While Driving
(ICNIRP) 1998. Check the laws and regulations regarding the use of radios in the
area where you drive, and always obey them. If you do use your
• Ministry of Health (Canada) Safety Code 6. Limits of Human
radio while driving, please:
Exposure to Radiofrequency Electromagnetic Fields in the
Frequency Range from 3 KHz to 300 GHz, 1999.
• Give full attention to driving and to the road.
• Australian Communications Authority Radiocommunications
• Use hands-free operation, if available.
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
• Pull off the road and park before making or answering a call if
• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
driving conditions so require.
• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
The use of a two-way radio while engaged in activities requiring
To ensure optimal radio performance and make sure human concentration may cause distraction or otherwise impair your ability
exposure to radio frequency electromagnetic energy is within the to safely participate in such activities. Always use technology safely.
guidelines set forth in the above standards, always adhere to the
Do not place a portable radio in the area over an air bag or in the
following procedures.
air bag deployment area. Air bags inflate with great force. If a
portable radio is placed in the air bag deployment area and the air
Portable Radio Operation and EME Exposure
bag inflates, the radio may be propelled with great force and cause
Antenna Care
serious injury to occupants of the vehicle.
Use only the supplied or an approved replacement antenna.
Potentially Explosive Atmospheres
Unauthorized antennas, modifications, or attachments could
Turn off your radio prior to entering any area with a potentially
damage the radio and may violate FCC regulations.
explosive atmosphere. Only radio types that are especially qualified
Do NOT hold the antenna when the radio is "IN USE." Holding the
should be used in such areas as "Intrinsically Safe." Do not remove,
antenna affects its effective range.
install or charge batteries in such areas. Sparks in a potentially Channels and Frequencies
explosive atmosphere can cause an explosion or fire resulting in
bodily injury or even death.
Channel Frequency
Note: The areas with potentially explosive atmospheres referred to
1 462.5625 MHz
above include fueling areas such as below decks on boats, fuel or
chemical transfer or storage facilities, areas where the air contains
2 462.5875 MHz
chemicals or particles (such as grain, dust or metal powders) and
any other area where you would normally be advised to turn off your
3 462.6125 MHz
vehicle engine. Areas with potentially explosive atmospheres are
often—but not always—posted.
4 462.6375 MHz
Blasting Caps and Areas
5 462.6625 MHz
To avoid possible interference with blasting operations, turn off your
radio when you are near electrical blasting caps, in a blasting area,
6 462.6875 MHz
or in areas posted "Turn off two-way radios." Obey all signs and
instructions.
7 462.7125 MHz
Operational Cautions
8 467.5625 MHz
Antennas
Do not use any portable radio that has a damaged antenna. If a
9 467.5875 MHz
damaged antenna comes into contact with your skin, a minor burn
can result.
10 467.6125 MHz
Batteries
11 467.6375 MHz
All batteries can cause property damage and/or bodily injury such as
burns if a conductive material—like jewelry, keys or beaded chains—
touch exposed terminals. The conductive material may complete an
Uruguay
electrical circuit (short circuit) and become quite hot. Exercise care in
Use of GMRS frequencies is subject to the Rules and
handling any charged battery, particularly when placing it inside a
Regulations of the Regulatory Unit Communications Services
pocket, purse or other container with metal objects.
(URSEC). URSEC requires that all operators using GMRS
Exercise care when removing NiMH or AAA batteries. Do not use
frequencies obtain a permit before operating their equipment.
sharp or conductive tools to remove either of these batteries.
The authorization shall depend on the channel availability at the
time the authorization is requested. To obtain a permit from
Battery Charger Safety Instructions:
URSEC, consult your local URSEC office for more information:
Save these Instructions
www.ursec.gub.uy.
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a
Panama
sharp blow, or has been dropped or damaged in any way.
The Republic of Panama does not require authorization to use
3. Never alter the AC cord or plug provided with the unit. If the
FRS/GMRS radio equipment frequencies.
plug will not fit the outlet, have the proper outlet installed by a
qualified electrician. An improper condition can result in a risk
USA
of electric shock.
Use of GMRS frequencies is subject to the Rules and
4. To reduce the risk of damage to the cord or plug, pull the plug
Regulations of the Federal Communications Commission (FCC).
rather than the cord when disconnecting the charger from the
The FCC requires that all operators using GMRS frequencies
AC receptacle.
obtain a radio license before operating their equipment. To
5. To reduce the risk of electric shock, unplug the charger from the
obtain the FCC forms, please visit the FCC's Web site at
outlet before attempting any maintenance or cleaning.
wireless.fcc.gov/uls/index.htm?job=home to source form 605
6. Use of an attachment not recommended or sold by Motorola
and 159, which include all the instructions you will need.
may result in a risk of fire, electric shock or personal injury.
7. Make sure the cord is located so it will not be stepped on,
If you wish to have the document faxed or mailed, or if you
tripped over or subjected to damage or stress.
have questions, please use the following contact information:
8. An extension cord should not be used unless absolutely
necessary. Use of an improper extension cord could result in a
For a fax:
risk of a fire and/or electric shock. If an extension cord must be
Contact the
used, make sure that:
Fax-0n-Demand
• The pins on the plug of the extension cord are the same system
number, size and shape as those on the plug of the charger.
1-202-418-0177
• The extension cord is properly wired and in good electrical
condition.
• The extension cord size is 18 AWG for lengths up to 100 feet,
Canada
and 16 AWG for lengths up to 150 feet.
No license is required in Canada for GMRS use.
9. The supply cord of the AC adaptor cannot be replaced. If the
cord is damaged, call customer service at the appropriate
number listed in the Warranty section.
Changes or modifications, not expressly approved by Motorola, may
void the user's authority granted by the local regulatory agency to
operate this radio and should not be made. To comply with local
regulatory requirements, transmitter adjustments should be made
only by or under the supervision of a person certified as technically
qualified to perform transmitter maintenance and repairs in the
Volume
private land mobile and fixed services as certified by an
organization representative of the user of those services.
Replacement of any transmitter component (crystal, semiconductor,
etc.) not authorized by the local agency's equipment authorization
for this radio could violate local government regulatory rules.
Push to Talk
Note:
• Use of this outside the country where it was intended to be
distributed is subject to government regulations and may be
prohibited. Call Tone
Licensing Information
Speaker
Your Motorola radio has 22 operating channels. The FRS channels
operate within the range of free use frequencies and do not require
authorization from your local regulatory body.
Mini-USB
The GMRS channels may require authorization from your local
Charging Port
regulatory body.
Display Screen Guide
Description Channel Frequency Description
GMRS 12 467.6625 MHz FRS
Numbers
GMRS 13 467.6875 MHz FRS
for Channel,
Call Tone
GMRS 14 467.7125 MHz FRS
Numbers
GMRS 15 462.5500 MHz GMRS
for Codes
GMRS 16 462.5750 MHz GMRS
- Battery Meter
GMRS 17 462.6000 MHz GMRS
- Channel Power
GMRS 18 462.6250 MHz GMRS
Indicator (see
Menu Options)
FRS 19 462.6500 MHz GMRS
- Lock
FRS 20 462.6750 MHz GMRS
FRS 21 462.7000 MHz GMRS
- Talk Confirmation
Tone (Roger Beep)
FRS 22 462.7250 MHz GMRS
- Noise Filtering
Getting Started
Installing the Batteries
Each radio uses 1 NiMH rechargeable battery pack or 3 AAA
alkaline batteries and beeps when the batteries are low.
Installing NiMH Rechargeable Battery Pack
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery cover latch
up and remove the cover.
3. Remove the battery pack from the clear plastic bag. (Do not
disassemble or unwrap the battery pack.)
4. Insert the NiMH battery pack with the diagram facing you.
5. Reposition the battery cover and press down to secure.
Installing the Three AAA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery cover latch
up and remove the cover.
3. Insert the three AAA alkaline batteries with + and - polarity as
shown inside.
4. Reposition the battery cover and press down to secure.
Radio Battery Meter
For mail service: If you have
The radio battery icon shows the radio battery charge level, from
Call the FCC questions about
full to empty . When the radio has one segment left, the
Forms Hotline the FCC License:
Call the FCC radio chirps periodically or after releasing
Removing the NiMH Battery Pack
1-800-418-FORM 1-888-CALL-FCC
(3676) (225-5322) 1. Turn the radio off.
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
3. Remove the NiMH battery pack by pulling the ribbon attached to
the battery.
4. Reposition the battery cover and press down to secure.
Control Buttons
Removing the Three AAA Batteries
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
3. Gently remove each battery by easing each battery out individually.
4. Reposition the battery cover and press down to secure.
Menu/Lock
Notes
• Exercise care when removing NiMH or AAA batteries. Do not
use sharp or conductive tools to remove either of these batteries.
• Remove the batteries before storing your radio for extended
periods of time. Batteries corrode over time and may cause
permanent damage to your radio.
Accessory Jack
Using the Battery Charger
The battery charger provides drop-in charging convenience for
Scan/Monitor
NiMH batteries and can be placed on any flat surface, such as a
desk or workbench. Charge the NiMH battery overnight (at least
16 hours) before using it for the first time. After the initial charge,
an empty battery is fully charged within 14 hours.
1. Follow the steps above to install a NiMH Battery Pack.
2. Plug the AC power supply cord into the jack on the desk stand.
Scroll/Weather
3. Plug the AC power supply into a standard wall outlet.
4. With a radio facing forward, slide it into one of the charging
pockets.
Microphone
5. When charging in the battery charger, the red light on the
charger base will glow continuously.
Using the mini-USB Charging Connector
The mini-USB charging connector is a handy port that allows you to
conveniently charge your NiMH battery pack. This is an alternative
to charging your NiMH battery pack in the Battery Charger desk
stand using the AC wall adaptor and especially useful when used
while traveling.
Available mini-USB charging options: (Optional Accessories)
1. Wall travel charger
On/Off for each 2. Vehicle charger
-
feature
3. Mini-USB computer cable
If using a computer, the computer must be turned on.
- Scan
This and other accessories (sold separately) are available for
your radio. For more information, visit our Web site at
- Call Tone, www.motorolasolutions.com/talkabout or shop.giantintl.com.
Keypad Tone
1. Plug your mini-USB cable or charger into a power source as is
appropriate for your accessory.
- Weather Alert
2. Plug the cable into the mini-USB port on the bottom of your radio.
3. An empty battery will be fully charged in 14 hours.
- Hands-Free Use
4. The LED indicator light on the radio will glow to indicate that the
Without
battery is charging.
Accessories
Notes
• The light will remain red after the NiMH battery pack is fully
- Hands-Free Use charged.
With Accessories
• When moving between hot and cold temperatures, do not
charge the NiMH battery pack until the battery temperature
acclimates (usually about 20 minutes).
• For optimal battery life, remove the radio from the charger within
16 hours. Do not store the radio while connected to the charger.
• If the radio is kept on while charging, the charging time will be
extended.
• Even though the charger is connected, you may not be able to
transmit a message if the battery is completely empty
Allow time for the battery to charge to 1 bar before
attempting to transmit a message.
Attaching and Removing the Belt Clip
1. Attach belt clip to pocket or belt strap.
2. Align the belt clip post with the hole in the back of the radio.
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to
release the catch.
2. Pull the belt clip away from the back of the radio.
Turning your Radio On and Off
Turn clockwise to turn the radio on and counterclockwise to
turn the radio off.
1. In the ON position, the radio chirps and briefly shows all feature
icons available on the radio.
2. The display screen then shows the current channel, code and
all features that are enabled.
Setting the Volume
(Low Battery Alert).
Press and hold for three seconds while rotating until you
reach a comfortable listening level.
1. Rotate clockwise to increase the volume.
2. Rotate counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
Talking and Listening
To communicate, all radios in your group must be set to the same
channel and Interference Eliminator Code.
1. To talk, press and hold .
2. When you are finished talking, release .
For maximum clarity, hold the radio two to three inches away from
your mouth and speak directly into the microphone. Do not cover
the microphone while talking.
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet apart.
Monitor Button
Pressing and holding for three seconds allows you to listen to
the volume level of the radio when you are not receiving. This allows
you to adjust the volume, if necessary. You can also press
check for activity on the current channel before you talk.
Push to Talk Timeout Timer
To prevent accidental transmissions and save battery life, the radio
emits a continuous warning tone and stops transmitting if you
press for 60 continuous seconds.
Continued on back
.
to
MH230