Advertisement
Internal \
exhaust
duct
dryel
rear
Y
6. [Insert elbow
end of duct pieces
through
the side opening.
Reach
through
the access
panel
openlng
and
attach
elbow
to the Internal
exhaust
duct.
Check
the length
of
stralght
duct
extending
out the
side of the cabinet.
If duct extends
too far to make
the exhaust
duct
connection,
mark a line around
the
stralght
duct
one Inch out from the
cabinet.
Remove
the duct and elbow
and cut the straight
pipe to the
length
needed.
Reinsert the duct
pieces.
Use duct
tape
to connect
the elbow
to the internal
exhaust
due
Repeat
for the other dryer.
>7. llnsert the plasttc cover
Into the rea
exha-ust opening.
8. jRe place
the access
panels.
9. \Use duct tape
to seal all joints.
To connect
exhaust
duct
through
the bottom
of the
lower dryer only -
Note: You must use a threesection
elbow
to connect
exhaust
duct
through
the bottom
of the tower
dryer.
I..\ Check
that the legs extend
one
inch from the bottom
of the dryer.
2.
i Remove
the lower dryer access
panel
by releasing
the two locking
clips with a small, flat-blade
screwdrtter.
The clips are located
four inches in from each
side of-the
access
panel.
Uft access
panel
off the bottom
clips and set aside.
Page 8
3.1 Remove
duct tape
from In .ernal
exhaust
duct and the straight
duct.
4.j
Remove
the screw from the I duct
clip tit
attaches
the straight
duct to
the back of the cabinet.
Dep Bss the
clip and remove
the straight c uct
using a twisting
motion
througl i the
rear exhaust
openlng.
5.1 Measure
from the large en( 1 of the
straight
duct and mark at four
inches.
Cut the stralght duct to that
6.j Reach
through
the rear ezd xlust
opening
and depress center
c tf tabs
on one of the side, plcxtic
opt ning
covers.. Remove
the cover.
7.1 With a Phillips screwdriver,
reach
through
the rear exhaust
oper ling
and remove
the screw that al taches
me cover
to the dryer base.
Carefully
remove
the cover ar d screw
through
the rear exhaust
oper ring.
floor Damage
Slide dryers onto cardbaal
d or
hardboard
before moving
across tloor.
Failure to do so mq.causc!
damage
to floor covering.
I
1
8.\, Move dryers into operatinc
pdsltion.
Reach through
the 2 access
opening
and mark the exhau: t
opening
location
on the floor. Move
dryers out of the operating
pc sition.
9.: Cut opening
through
the fl oar.
::
I
: I --
4Aont
of dryer
10. :Push the four inch, stralght duct
through
the rear exhaust
opening
and onto the Internal
duct as far
as it will go.
I
.
ol!
*front
d dryer
7 1. j Insert
me
elbow
through
the
rear exhaust
opening.
Ins& elbow
into the bottom
exhaust
openina.
+ tront
of dryer
12.'Slide the straight
du
elbow
approximatety
one inch.
Use duct tape to seal both joints.
.
sc,ew h&d
x-
(fastens against
edge of cabinet)
iili~rt
the
bottom
exhaust
-cover
through
the side exhaust
opening.
Put me
cover
over
me
rear exhaust
opening
with the
tab pointing
down
to bottom
of dryer.
Insert screw through
the hoie In the
cover
that Is on the &tslde
of the
cabinet.
Ttghten screw.
14jReptace
the side exhaust
cover.
15. (Move the dryers into operating
position.
Check
that the elbow
Is
through
the bottom
exhaust
opening.
Replace
the access
panel.
763onnect
the elbqy
toe-must
d&t.
Then connect
exhaust
duct
to exhaust
hood or maln exhaust.
Use
duct tape to seal all Joints.
Advertisement
